Variable Optical Attenuators
Adjust the power of an optical signal.
-
Product
Electrical and Optical & Bit-Error-Rate Testers (BERTs)
OptoBERT™
-
The OptoBERT family of BERTs offers the best value in the industry for bit-error-ratio testing of optical and electrical components, subsystems and systems. OptoBERT family of products covers data rates from 100 Mb/s to 28.05 Gb/s.
-
Product
Fiber Optic Network Simulators
SIM-2FON-25
-
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types. This product is ideal for latency testing, product development and training and educational needs.
-
Product
PXI Optical FPGA Board
PXIe-8324-DSP
-
The Conduant PXIe-8324-DSP FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations.
-
Product
Optical Detector
LG-9200
-
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
Product
Optical Profilers
-
Finally, measurements of surface roughness and topography can be made for a price that's less than that of a stylus profilometer. The Profilm3D has sub-nanometer vertical resolution, which surpasses optical profilometers that cost 3x as much. It does so by using the same state-of-the-art measurement technologies as the most sensitive optical profilers available: vertical-scanning interferometry (VSI) and phase-shifting interferometry (PSI).
-
Product
Optical Parametric Amplifier
-
AVUS is an Optical Parametric Amplifier (OPA) that provides widely tunable high energy pulses and high repetition rates (up to 1 MHz). AVUS offers highest average output power on the market and is designed for 1 µm fs pump lasers.
-
Product
Optical Measurement Methods and Characterization Services
-
The Fraunhofer IOF develops optical measurement methods and systems to customer requirements. Key areas include the characterization of optical and non-optical surfaces, coatings, components and systems in the micro and sub-nano range as well as 3D shape acquisition.
-
Product
Optical Power Meters
-
Artifex Engineering GmbH & Co. KG
The OPM series of optical power meters (OPM) employs photodiodes for the measurement and monitoring of optical power from the UV to near IR.
-
Product
Attenuator Modules
-
The Analog Devices portfolio of wideband digital attenuators and voltage variable attenuators (VVAs) modules helps meet designers’ diverse needs. Low cost, high accuracy control, and small package options provide solutions for RF and IF applications, including the space, communications, and military industries.
-
Product
Optical Components & Transmission Simulation Software
VPIphotonics Design Suite
-
VPIphotonics Design Suite™ embeds expert knowledge from our component and transmission design tools in one shared, flexible software environment to support requirements in design, analysis and optimization providing you with the most powerful numerical algorithms tailored for your applications.
-
Product
TS Optical Transmitter / TS Optical Receiver
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
A 4-way TS optical transmitter can long distance transfer 4-way MTS(multi programs transfer stream) from 4 difference multiplexer output in same optical fiber, then At optical receiving terminal, A TS optical receiver will change the optical signal to 4-way independent standard TS output。
-
Product
Fiber Optic Terminus
ARINC 801
-
The ARINC 801 fiber optic terminus is the next generation of high density, butt joint interconnect technology. With its standard 1.25 mm ferrule and sleeve, the ARINC 801 terminus is designed for both multimode and single-mode applications. For the pull-proof design, the cable jacket is crimped on an external body and a floating mechanism avoids any loss of performance when pulling on the cable. This feature allows for the use of the connector without a backshell. Standard connector formats include MIL-DTL-38999 type, MIL-DTL-83527 type, ARINC 600 and ARINC 781.
-
Product
High-Power InGaAs Optical Head
81626C
-
The new 81626C high-power optical head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81626C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
Optical Time Domain Reflectometers
-
An optical time domain reflectometer (OTDR) is a precision instrument used to locate events or faults along a fiber link, typically within an optical communications network. The OTDR launches a series of high speed optical pulses into the fiber to be measured. Various events on the fiber generates a Rayleigh back scatter that returns to the OTDR and the strength of the return pulses are measured and integrated as a function of time, and plotted as a function of fiber length. The horizontal axis is the distance and the vertical axis is the loss.
-
Product
Dual Attenuator
V859
-
The Model V859 is a passive dual section attenuator housed in a 1-unit VME module; the module does not require any power supply since it is made up of resistive cells
-
Product
Fiber Optic Visual Fault Finder
VFF5
-
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
Product
High Power Optical Head With Integrating Sphere
81628C
-
The 81628C High-Power Optical Head features an integrated sphere that enables it to handle power levels up to +40 dBm (with heat sink), across 800 nm to 1700 nm wavelength range. It provides the highest accuracy at high power within the family.
-
Product
Optical Access
-
CXR offers a choice of conversion and optical transport Ethernet or TDM streams, and CWDM optical multiplexing.
-
Product
Mini Optical Spectrum Analyzer
-
Shenzhen Golight Technology Co.,Ltd
Mini OSA is based on MEMS tunable filter and high precision photoelectric control unit and detection unit. Its measurement precision is superior to the traditional OSA in C-band and O-band. And built-in USB communication interface is easy for system integration and SDK.
-
Product
Optical Spectrum Analyzer
ID OSA
-
This instrument is a versatile Optical Spectrum Analyzer (OSA) based on a coherent detection principle provides picometer class spectral resolution across the C-Band (1528.5 – 1567.5nm).
-
Product
Indoor Mini Optical Receiver
SR1020
-
Hangzhou Softel Optic Co., Ltd.
Designed for FTTH(Fiber To The Home) networks ●Excellent linearity and flatness●Wide range of optical input power ●Single-mode fiber high return loss ●Using GaAs amplifier active devices ●Ultra low noise technology ●Smaller size and easier install ●Red-LED for power indication ●Color-LED for optical power indication●Double color LED for optical power indication (Non-lighted: optical power<-10dBm, Green:-10dBm
+3dBm) -
Product
90-Degree Optical Hybrid
-
Six-port hybrid devices have been used for microwave and millimeter-wave detection systems since the mid-1990s and are a key component for coherent receivers. In principle, the six-port device consists of linear dividers and combiners interconnected in such a way that four different vectorial additions of a reference signal (LO) and the signal to be detected are obtained. The levels of the four output signals are detected by balanced receivers. By applying suitable baseband signal processing algorithms, the amplitude and phase of the unknown signal can be determined.
-
Product
Fiber Optics
-
The Neoptix product line includes fiber optic temperature sensors for transformer windings temperature monitoring and for laboratory, industrial, and medical applications.
-
-
Product
Optical Device
-
Optical devices are products that use the optical characteristics (birefringence) of quartz crystals. Murata Manufacturing uses high-precision synthetic quartz crystals grown using our proprietary technology to manufacture high-grade products.
-
Product
DC Bias Attenuators
-
a fixed DC Bias attenuator from Pasternack. This 10dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
-
Product
Fiber Optic Sensors
-
Leuze electronic GmbH + Co. KG
Plastic fiber optics are suitable for universal applications with low space requirements for object detection. Glass fiber optics are used in demanding environmental conditions with high temperatures and are resistant to chemicals. For radiation through foils or applications with high light power, they offer further advantages through the especially low damping. The flexible fiber optics with various head shapes can be integrated in nearly any system design. The detection range is dependent on the fiber optics and amplifiers used. Fiber optics can be used with the throughbeam principle or with scanning function. As a fiber array with multiple light beams, they can be used to detect especially small objects.
-
Product
Single Mode Fiber Optic Rotary Joints
-
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
Product
Coaxial Programmable Attenuators
-
Coaxial attenuators are constructed with passivated stainless steel for durable use in both engineering labs and production line environments. These coaxial attenuators are designed and manufactured for low VSWR, low insertion loss and high attenuation value accuracy. The standard offering covers the frequency range of DC to 110 GHz and includes various interface options from 2.4 mm to 1 mm connector types as well as both male and female interfaces. The power handling of standard models is 0.5 to 1 watt continuous wave (CW). Higher power handling levels and different attenuation values and connector types from those listed below can also be requested.
-
Product
1310nm Direct Modulated Fiber Optical Transmitter
ONT-8600AS
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai 1310nm direct modulation fiber optical transmitter, adopts high linearity DFB laser of famous brand in the world, and builds-in perfect pre-distortion adjustment circuit and laser APC, ATC closed loop control circuit. All the operating parameters of fiber optical transmitter are controlled by microprocessor, and the LCD screen on the front panel can display relative operating status and the fault information.
