Compliance Test
The assurance of device compliance with specifically defined requirements.
-
Product
Radar Altimeter Test Set
Core Technology
-
Eastern OptX core technology enables the conversion of microwave signals to optical signals (E/O), time delaying this signal then reconverting the light back to original microwave signal (O/E) with superior fidelity over traditional time delay methods. Products include Radar Target Simulation, Radar Altimeter Testing, Channel Simulation (Air Interface) and Multipath Creation.
-
Product
Microwave Testing
50A
-
The GGB Industries, Inc., MODEL 50A probe sets new standards in microwave probing performance. Using low loss coaxial techniques, the Model 50A achieves an insertion loss of less than 1.0 db and a return loss of greater than 18 db through 50 GHz.
-
Product
Turn-Key Test Solutions
-
Our Product line cover the very basic of safety test needs. We have products focus on single safety test like Hipot, Ground-Bond, Leakage-Curret and Insulation Resistance. Advanced models combining all the safety tests function together.
-
Product
Solar PV Testing Services
-
Atlas Material Testing Solutions
Can your product stand up to the harshest environmental conditions? Atlas Testing Services can provide manufacturers with the data they need to demonstrate long-term durability and to support warranty and performance claims while reducing the costs associated with aftermarket product failure.
-
Product
Bridge Decking Testing Equipment
-
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
Product
Gravity Test Handlers
-
Microtec offers a wide variation of customizable gravity handlers. The focus of our systems is based on the approach to provide 1 system for many different applications. By pursuing continuous improvements and setting the objective to provide our customers the most convincing test handlers, we are always driven to push our products and its features to the limits and exceed traditional boundaries.
-
Product
2.5mm Test Wire Test Probe Pin
CX-3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test wire test probe pin 1.Application: Used to verify the protection of persons against access to hazardous parts. Also used to verify the protection against access with a tool.
-
Product
Manual Testing
-
At UpDoer Technology, we're dedicated to providing you with quick and accurate test results. We offer a range of manual testing services to fulfill your needs and keep your projects on schedule and within budget. We follow a test-driven development approach to ensure quality at every moment of the software development cycle.
-
Product
Test Equipment
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Test Equipment, including handheld electrostatic fieldmeter, periodic verification system, charged plate monitor, contact voltmeter, and others.
-
Product
Bluetooth Tests
-
Devices that are equipped with Bluetooth® technology must, on the one hand, meet the respective country-specific regulatory test requirements, such as B. in accordance with FCC, ISED or CE, as well as test requirements of organizations such as the Bluetooth® SIG or the CTIA have to pass and meet in order to obtain market approval.
-
Product
E-Motor Testing
TITAN eDrive
-
The progressive electrification of the powertrains in the mobility sector makes it necessary to test the individual drive motor and its inverter on the test bench in addition to complete powertrain investigations. In addition, electrified drives are now being used in a wide variety of vehicles on land, water or in the air.
-
Product
LED Test Instruments
-
Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Torque Test Kit
G201A11-16
-
To determine whether components of child-related products can be removed by a certain torque force. A torque-measuring device is used in conjunction with a torque clamp to record the applied force. Any projection, part or assembly of a child-related products that a child can grasp with at least the thumb & forefinger or the teeth shall be subject to the torque test.
-
Product
Instrument Test Unit
-
Instrument Test Unit For Advanced Inertial Sensors (INTU) is used for testing and evaluation of Ring Laser Gyro (used in GSLV/PSLV launch vehicles), that detects the angular displacement during rotation. The INTU receives displacement signals from the sensor (RLG) to evaluate the sensor characteristics and also generates signals required towards initiating the action of the sensor.
-
Product
Coating Testing
-
Makes it possible to predict their durability and how they will be affected by the passage of time.
-
Product
Speaker/Receiver Unit Test Generator
BK2019
-
The BK2019 Generator is easy to operate, simple to set up, and you can fit it just about anywhere. This portable generator produces tones or sweeps and is technology you can whip out of your briefcase, plunk down on a table and start using. It's equally useful for either spot checking or for quality control. The setup is so easy that you can change DUT's in minutes.
-
Product
Sound Testing
SP series
-
Are ideal for on-site measurements in accordance with the noise at work legislation for industrial and office environments.
-
Product
Test Charts
iQ charts
-
Image Engineering GmbH & Co. KG
The basis of our test chart portfolio are the ESSER TEST CHARTS owned by Image Engineering and known worldwide for their high quality which we continually improve. Included in the extensive program are HDTV charts for broadcast, multipurpose charts as well as the UTT chart (Universal Test Target), the leading system for the standardized digitalization of archives, which is already being used by the Metropolitan Museum in New York.
-
Product
Agree Test Chambers
-
Agree test chamber are designed to perform specific temperature, humidity and vibration test to improve the quality and reliability of components. The Agree method of testing is an acronym for the Department of Defence Advisory Group Reliability of Electronics Equipments. This chamber also known as Temperature Humidity Vibration Test chamber and Stress Test Chamber
-
Product
Shore Durometer Test Stand
UI-FT31
-
Shore Durometer Test Stand is used to support the durometer presser foot surface parallel to the sample support table to better complete the test.
-
Product
Lens Test Equipment
-
ZEISS lenses for technical applications are key components in complex production processes (Machine Vision) as well as in optical metrology, medical applications, traffic enforcement, quality assurance, sports and many other applications. Here they prove their outstanding image performance and reliability. Due to the precise manual adjustment of the helical focusing mount our partners will gain much better results than with comparable lenses.
-
Product
Meter Test Board
MTB-3200
-
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
Product
Environmental Test Chamber
-
Test Chambers are used widely in temperature variation tests, cold resistance tests, and for low-temperature storage in the areas of aerospace and aviation, electronic instruments, electrical products, materials, parts, and components.
-
Product
Electrical Safety Testing
-
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
Product
Salt Spray Testing
-
Salt Spray testing (Also known as Salt Fog testing) is often used for testing the corrosion resistance of metallic products, or for testing the corrosion resistant coating applied to metallic products, in order to verify that they will function properly when exposed to salt corrosion. This specific type of testing is used as a means to accelerate the salt corrosion exposure in order to gather data on the long or short term effects of salt corrosion on the product or coating material.
-
Product
Android Testing Services
-
We now live in a digital world. A world where reality can be augmented, choices can be predicted and strangers can be befriended within seconds.
-
Product
SNMP Test Suite
SilverCreek
-
SilverCreek is the Authoritative SNMP Test Suite -- designed to test implementations of the Simple Network Management Protocol (SNMP agents) and standard and private MIBs (Management Information Bases). SilverCreek incorporates thousands of small, single function tests written in the Tcl scripting language to exercise one or a small number of parameters. The syntactic tests verify protocol compliance, error and exception handling, and boundary condition behavior. The functionality tests (semantic tests) verify performance, trap/alert/event/notification handling, counter accuracy, security, and many other implementation specific areas.
-
Product
Aviation Engine Test Cells
-
1.Design, manufacture and installation: ● Thrust stand components: thrust measurement system, adapter, superstructure etc. ● Facility subsystems: DAQ, supply systems (fuel, oil) etc.2.Civil construction works: site survey, building works etc.3.Contracting: ● Turn-key – MERA is able to supply a “turn-key” test cell including civil works, thrust stand, DAQ, all necessary facility subsystems, specialized software, throttle control level and etc. ● Joint – MERA is capable to supply specified items such as thrust stand with DAQ and software. The Customer is able to procure necessary items such as test nacelle directly from OEM. 4.Project management in accordance to EPC (Engineering, Procurement, Construction, FIDIC) 5.Certification in accordance to international and local standards and rules (SAE 5305) Engine types: PD-14, PS-90, RD-93, RD-33MK, AL-31FN
-
Product
Container & Package Testing
-
*Incline Impact. *Drop. *Cobb. *Static and Dynamic Compression. *Dart Puncture. *Environmental Conditioning. *Vertical Linear, Rotary Motion, Sinusoidal and Random Vibration. *Internal Pressure. *Vacuum
