Parallel Digital I/O
Processes multiple bits or data paths simultaneously.
-
Product
Parallel Memory Test Solution
Magnum2
-
Teradyne’s Magnum 2 test system delivers high throughput and high parallel test efficiency for high performance non-volatile memories, static RAM memories and logic devices.
-
Product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
-
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
Product
PCI Express Digital I/O Boards
PEX-1002H
-
PCI Express, 32-ch, 12-bit, 44 kS/s High Gain Multi-function DAQ Board. Includes CA-4002 D-Sub connector
-
Product
PCI-6123, 8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O DeviceMultifunction I/O Device
779409-01
-
8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O Device - The PCI‑6123 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6123 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6123 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
Digital I/O Card w/CoS IRQ
PCIe-DIO-24HS
-
This product is a x1 lane PCI Express digital I/O board available in two models. The PCIe-DIO-24H is the basic DIO and the PCI-DIO-24HS features advanced change-of-state (COS) detection capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
Product
NI-5734, 120 MS/s, 16-Bit, 4-Channel Digitizer Adapter Module for FlexRIO
781659-04
-
The NI‑5734 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples four channels at 120 MS/s. You can use the NI‑5734 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5734 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
32-CH Discrete Output Module
HSL-DO32-M-N/HSL-DO32-M-P
-
Slave ID consumption: 2 consecutive from odd"N" type for NPN sinking type outputSwitch capacity: Single channel 500 mA; all channels 60 mA at 24VDCPhoto couple isolation voltage: 2500 VrmsResponse time: ON→OFF: 180µs, OFF→ON :1.2µsLED indicator: Power, Link and Output statusPower supply: +10V to +30 VDCOperating temperature: 0 to 60°C
-
Product
3U OpenVPX SOSA™-Aligned MFIO-Intensive Processing Board
68G6
-
The 68G6 is a SOSA™-Aligned 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. In addition to the standard expansion plane (EP) PCIe and control plane (CP) Ethernet control interfaces, the 68G6 facilitates convenient external access to supported NAI PCIe function modules through its 1 x1 PCIe interface, enabling seamless expansion of host SBC functions for enhanced project solutions, while also offering external access to supported NAI FMx modules via a SATA II interface. The 68G6 is on NAI’s certifiable product development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G6 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Configurable 3U OpenVPX Multifunction I/O Boards
-
NAI offers a variety of 3U VPX solutions, including rugged I/O Boards and SBCs - designed to be combined with our smart function modules - to create a COTS-based, high-density, multifunction I/O solution for most sense and response requirements.
-
Product
Digital Channel, 10 MΩ Input, ±25 V, 8 Channel
CX1152A
-
The CX1152A Digital Channel provides 8-channel digital trigger for the CX3300 Device Current Analyzer series, which is useful when a low power device with digital I/Os is evaluated. Only the CX3324A mainframe has the interface of this product. The input impedance of each channel is 10 MΩ in order to minimize the load current from the digital channel.
-
Product
Digital I/O Card w/CoS IRQ
mPCIe-DIO-24S
-
The mPCIe-DIO-24S is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
Digital to Synchro-Digital to Resolver Converters
ST-DRL ST-DSL ST Prefix
-
Computer Conversions Corporation
Terminations subject to converter module features where applicable.Plastic backplane mount track included, or may be mounted using spacers at mounting hole locations.
-
Product
PCI Express Digital I/O Cards
-
Sealevel PCI Express digital I/O cards are designed for computers with X1 PC Express slots and are compatible with any PCI Express slot. Digital I/O cards are currently available with optically isolated inputs and Reed relay outputs. Optically isolated inputs protect the PC from voltage spikes common to industrial environments while Reed relay outputs provide reliable, long-life switch closures suitable for low current applications.
-
Product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 1 Channel, 500 MHz Bandwidth
M4I.2210-X8
-
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
4-Ch High Speed Analog Input EtherCAT Slice IO Module
AMAX-5017H
-
Channels : 4 (Differential)Input Type : V, mAVoltage Range : ±10 V, 0 ~ 10 V, 0 ~ 20 mAInput Impedance : 800 kΩ, for voltage input, 500 Ω, for current inputResolution : 16-bit with ±0.1% for voltage input, 16-bit ±0.2% for current inputFSR accuracy : @25°CSample Rate : 10k sample/s (per channel)
-
Product
PXIe Digitizer: 500 MSa/s, 14 bit, 200 MHz
M3102A
-
The M3102A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
Product
Dynamic Digital I/O Instrumentation
-
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
Product
PXI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
779629-01
-
The PXI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Digital and Serial I/O
-
VadaTech’s wide range of ATCA Rear Transition Modules (RTMs) and MicroTCA I/O AMCs make it easier to integrate these standards-based building block systems into your network or application.
-
Product
6.5 and 7.5 Digit Multimeters
Truevolt Series
-
Truevolt digital multimeters (34460A, 34461A, 34465A, 34470A) enable you to get quick insights, measure low-power devices, and maintain calibrated measurements with Keysight’s new patented technology. Truevolt offers a full range of measurement capabilities with higher levels of accuracy, linearity, speed, and resolution.
-
Product
PXI-6284, 32 AI (18-Bit, 625 kS/s), 48 DIO, PXI Hybrid, Multifunction I/O Module
779122-01
-
32 AI (18-Bit, 625 kS/s), 48 DIO, PXI Multifunction I/O Module—The PXI‑6284 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2233-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXI Digital I/O And Prototyping Modules
-
Programmable Input Threshold and High-Side or Low-Side Drive Capability Available on Some ModulesOptically Isolated Input/Output for Interfacing to Electrically Noisy Environments Available on Some ModulesTTL Inputs and Outputs Suitable for Interfacing to External LogicOpen Collector/Drain Transistor Output Versions Suitable for Driving Internal or External Relay Coils
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-01
-
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Digital Multimeters
-
Digital Multimeters measure voltage, resistance, current, capacitance, inductance, and temperature. Some models also have an isolated digitizer mode. Use these products to test consumer electronics, fuel cells, aerospace production, and more.
-
Product
Digital Output
VME-2170A
-
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
Product
Digital Multimeters
T3DMM Series
-
Teledyne Test Tools new T3DMM series are dual display digital desktop multimeters that provide a rich and powerful feature set. The design is easy-to-use from the front-panel and computer-based control via USB or LAN. Each model is equipped with a 4.3 inch TFT-LCD true color screen with 480 * 272 resolution for easy viewing. The T3DMM series also features numerical data display, histograms, trend charts, bar charts and statistics, in addition to the built-in arithmetic functions including Measurement statistics.
-
Product
PCI Digital I/O Boards
PIO-D144U
-
Universal PCI, 144-channel OPTO-22 DIO board. Replacement unit for DIO-144.
-
Product
PCI Digital I/O Boards
PISO-P8R8
-
The PISO-P8R8 is an 8-channel isolated input/output interface board for the PCI-Bus computers.The PISO-P8R8 provides 8 electromechanical relay outputs and 8 optically isolated inputs, while PISO-P8SSR8AC and PISO-P8SSR8DC can be used in various applications including contact closure, external-voltage sensing,external-switch sensing and loading switching and designed for one 37-pin D-Sub connector.It can be installed in a 5V PCI slot and can support true "Plug & Play"
-
Product
Digital Module For Remote I/O
-
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
