WiFi Detectors
Locate wireless internet signal.
-
Product
Accumulation Leak Detector
LDS3000 AQ
-
LDS3000 AQ is the first leak detector to use forming gas or helium in a simple accumulation chamber. Leak detector uses cost efficient forming gas or helium for accumulation leak testing. The LDS3000 AQ is very sensitive and can detect leaks down to the 10-5 mbar∙l/s range. It will detect fluid leaks as reliably as helium vacuum leak testing, but with cost nearly at the cost of air testing. The real differentiator: The leak detector uses the cost efficient forming gas or helium for accumulation leak testing.
-
Product
Thermal Traffic Detector
TrafiSense
-
TrafiSense is an integrated thermal sensor and detector for vehicle and bike detection. TrafiSense does not need light to operate, but uses the thermal energy emitted from vehicles and bicyclists. This enables the sensor to detect vehicles and bikes in the darkest of nights, over a long range and in the most difficult weather conditions. The result is reliable, 24/7 traffic detection for a wide range of applications.
-
Product
Voltage Detectors
JSC
-
The JSC family of devices provides a highly reliable way to determine if voltage is present downstream of the disconnector or circuit breaker knives during zero-energy shutdowns. They dramatically increase the safety of personnel performing maintenance on electrical equipment. When voltage is present downstream of the disconnector knives, one or more LEDs on the JSC-88A will remain illuminated. The JSC's compact design allows for direct installation on the disconnector door, starter, or control panel.
-
Product
Photo Detector Testing
-
With the rise of 5G technology and popularization mobile devices, more and more advanced photoelectric sensors are used in our daily lives. In order to be better applied to mobile devices, the photosensitive area of these advanced photodetector is getting smaller and smaller. However, these applications place higher and higher requirements on the light sensing performance of advanced photodetectors. In the process of shrinking the photosensitive area, it also brings the challenge of accurate measurement of quantum efficiency. Enlitech adopts the spatial light homogenizing technology and follows the ASTM standard “Irradiance Mode” test method, which is proven that it can accurately perform quantum efficiency and other key parameter measurements of advanced photodetectors.
-
Product
Toxic Gas Detector
SMC 4501-XX
-
The SMC 4501-XX Detector monitors toxic gases such as Hydrogen Sulfide, Carbon Monoxide, Oxygen Deficiency, Chlorine Dioxide, and others. Utilizing 2-wire loop-powered technology, the 4501-XX requires less wiring, leading to better protection from wiring errors.
-
Product
Active Bat Detectors
-
The all-in-one device designed for active bat detection and recording.
-
Product
Torque Detectors
RH series
-
High rigidity: highly accurate detection of torque fluctuation with high response. The RH series is a torque detector that can accurately detect torque fluctuations with high torsional rigidity about 4.5 times compared to the existing products.
-
Product
Schottky Mixer And Detector Diodes
-
Majority carrier diodes formed by plating a layer of metal on a layer of doped semiconductor, which forms a rectifying junction.
-
Product
Fixed Gas Detectors
DG7 Series
-
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
Product
Pole Detectors
-
The tip of the unit detects the field polarity. The magnet surface is placed parallel to the unit tip. Two 1.5V AA battery operated. Power ON Switch activates the sensors and gives visual indication in form of two LEDs placed on the arm of the unit.
-
-
Product
Probes, Cables & Detectors
-
Probe has a mica window that has a thickness of 1.8 to 2.0 mg/cm2. This allows detection of alpha radiation as low as 3.0 MeV when in close proximity to the window. Beta radiation in excess of 35 keV and X-ray or gamma radiation greater than 6 keV can also be deteched. The detector is provided with a BNC connector. It can be used with most count rate and survey meters which accept Geiger Mueller (GM) detectors operating at 900V DC.
-
Product
4DI/4DO 2.4G WiFi IoT Wireless I/O
WISE-4050
-
Supports IEEE 802.11 a/b/g/n (2.4GHz)Supported protocols: Modbus/TCP, TCP/IP, UDP, DHCP, HTTPs, MQTTStores 10,000+ data points locally with SNTP/RTC time sync and WDT auto connection recoverySupports RESTful web API in JSON format for IoT integrationWith UDP-based AES-128 encrypted wireless P2P, abnormal inputs can automatically trigger up to 16 WISE modules in the field
-
Product
High Speed Rotation Type Torque Detector
DD series
-
The DD series torque detector is the high-end equipment of the SS series to use in high speed measurement and large capacity measurement. It can be recommended to use in the heavy-duty application from DD-505 to DD-108. Double bearings provides three to five times the strength of our conventional torque detector under radial and thrust load, which enables direct coupling to automobile engines and saves the space as it makes a conventional intermediate bearing unnecessary. The oil drip lubricant (option) is necessary for the DD series.
-
Product
Single Gas Detectors
-
Designed to monitor the air for the presence of one specific hazardous gas.
-
Product
Dual Voltage Detector / Maintenance Tester
MicroPhase I
-
Hachmann Innovative Elektronik
MicroPhase I is an easily operated phase comparator, dual voltage detector and maintenance tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-testers warn against defect interfaces. The integrated "Universal Phase Comparator" compares two different interface signals, even if they are of different interface type or voltage. A unique error control avoids switching errors caused by erratic or unfeasible phase comparison.
-
Product
Carbon Dioxide (CO2) Gas Leak Detector
-
Carbon dioxide detectors detects the presence of CO2 molecules in the air based on the absorption of infrared light.
-
Product
ChromaPoint Detectors
E50
-
Sciences et Techniques Industrielles de la Lumière
E50 series is part of the STIL ChromaPoint detectors.All the optical fibers are passive components, graduated index silica fibers with a 50µm core, an E2000/APC connector for the connection with STIL controller and an FC/APC connector for the connection with STIL optical sensor head.
-
Product
Detector And FPA Testing
-
The FPA Test Set (FPATS) interface to the detectors under test (DUT’s) is via a custom pedestal plate which provides both a conductive heat path to both the individual DUT’s as well as the field of view limiting aperture plate. This custom pedestal plate protrudes through the customer provided DUT interface printed circuit board (PCB) and makes physical contact with the rear of the DUT packages and the aperture plate when the FPATS is in the closed position. The pedestal plate is mounted to the ambient source plate and its temperature is actively driven by this subsystem.
-
Product
Multi-spectrum Infrared Flame Detector
975MR
-
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
Product
Personal Safety Voltage Detector
286 SVD
-
Standard Electric Works Co., Ltd
● Compact, easy-to-wear and convenient to use.● Waterproof design, protection class : IP68.● Indoor and outdoor use.● Equipped with self-testing functions.● Able to sense all kinds of AC high voltage system.● Low power consumption.
-
Product
Wi-Fi Interception System
-
Wi-Fi networks have become very popular among the current generation as a secure means of communication and browsing. Interception of the Wi-Fi networks can enable the LEAs to collect information with immense intelligence value.
-
Product
Phantom Pharmaceutical Metal Detector
-
The Phantom Pharmaceutical metal detector provides the ideal solution for detection and rejection of the smallest contaminants in tablets and capsules. With its current GMP design and construction suited for FDA compliance, the system meets the stringent QA requirements of the pharmaceutical industry. A free IQ/OQ Validation package is included. Built with a rugged mirrored stainless steel exterior, contact parts are all removable for cleaning without the need for tools. This compact detector can be easily angled and height-adjusted to suit any press configuration. Plus, it’s the only detector that features an electrical powered lift.
-
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
-
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Hybrid Picosecond Photon Detectors
HPPD Series
-
technology.The HPPD is our latest development in TCSPC detector technology that combines the benefits of conventional PMT design (wide spectral response and large active area)with the advantages of solid state APD technology (good detection efficiency, negligible after-pulsing and exceptional temporal resolution). Hybrid detectors are becoming thefirst choice for FLIM and short lifetime determination.
-
Product
Phantom Pipeline Metal Detector
-
The Phantom IP69K certified Stainless Steel Pipeline system detects metal contamination in pumped liquids and pastes conveyed through its non-metallic pipe. The extra-rugged BSH casing enables the system to withstand the harshest production environments. Pipe material options include nylon, rubber, and Teflon wrapped pipe for higher pressure / temperature applications. The Diverter Valve reject system is typically used to divert contaminated product from the flow. A test ball insertion/retrieval kit is offered as an option with Pipeline systems, allowing for ease of manual testing.
-
-
Product
Remote Speed Test, Wi-Fi
-
Measure Wi-Fi performance — at key locations, 24×7. Remote Speed Test automatically runs network and app performance tests all day, every day. Just connect the Remote Speed Test sensor to your Wi-Fi and we’ll do the rest! Performance results collected by all your sensors are delivered conveniently to your smartphone. 802.11 b/g/n/ac 2.4 and 5.0 GHz
-
Product
Non-RMS Responding Power Detectors
-
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
