PMC Modules
-
Product
PXI 12-Slot BRIC Matrix, 264x8 2-Pole (12 sub-cards)
40-562B-322-264X8
Matrix Switch Module
The 40-562B-322-264X8 is a high density BRIC12 matrix module with a size of 264x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
PXI 4 Slot BRIC 150x8 1-Pole (5 sub-cards)
40-561A-021-150X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI High Density 32x64 2A Matrix with BIRST
60-552-023
Matrix Switch Module
It is constructed from 8x64 sub-assemblies, permitting the matrix to be supplied in a variety of sizes from a single 16 x 64 to 64 X 64 and dual 8x64 to 32x64. Larger configurations can be easily achieved by utilizing the Loop thru connections on either the X or Y bus, for instance, four 64x64 units can be linked to create a 128x128 matrix.
-
Product
Signal/Micro Power/Micro Coax, Module, ITA, i2 MX, TriPaddle, 9/9 Position
510144004
ITA Module
Signal/Micro Power/Micro Coax, Module, ITA, i2 MX, TriPaddle, 9/9 Position.
-
Product
PXI 10 Banks of 16 Channel 1 Pole MUX
40-615-022-10/16/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
PXI 4 Slot BRIC 33x16 1-Pole (3 sub-cards)
40-562A-021-33X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI Optical Switching - 32:1 Multiplexer Plugin Module
65-281-315
Multiplexer Module
The 65-281-315 32:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
8-Slot BRIC, 210x12, 1 Pole, PXI Matrix (5 Sub-cards)
40-559-801-210x12
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
8-Ch SPST 12A-250VAC 24VDC Mux
H62004700
Multiplexer Module
This module is ideal for switching up to 12A. Composed by eight relays organized in two trees of four with two relays (One in each tree) with NC contact available. The module is shielded in order to reduce the radiated interference in high current switchings.
-
Product
PXI Solid State Multiplexer, 30 Amp, Single 6-Channel
40-667A-012
Multiplexer Module
The 40-667A-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, SMB
40-835A-001
Multiplexer Module
The 40-835A-001 (PXI) and 42-835A-001 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-110
Programmable Resistor Module
The 40-254-110 (PXI) and 42-254-110 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 31Ω with 0.125Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
NI-5792, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782511-01
RF Adapter Module
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
Product
PXI BRIC4 FIBO Matrix Dual 62x4 2pin brkout
40-592A-012
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Failsafe
40-785C-571-T
Multiplexer Module
The 40-785C-571-T (PXI) and 42-785C-571-T (PXIe) are single failsafe SP6T 67 GHz with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 8-Bank 26.5GHz SMA
60-801-308
Multiplexer Module
The 60-801-308 is a 6-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 773kΩ
50-297-143
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Very High Density Mux 24 Ch 8 Pole
40-670A-022-24/8
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, SC/PC Connectors
42-860A-222
Switch Module
The 40/42-860A-222 is a PXI/PXIe dual insert/bypass switch with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
LXI Microwave Multiplexer, SP4T, 13-Bank, 50GHz, 50Ω, SMA-2.4
60-803-613
Multiplexer Module
Our 60-803-613 is a 13 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 9-Channel, 1-Pole
40-321-104-HI
Multiplexer Module
The 40-321-104-HI (PXI) and 42-321-104-HI (PXIe) are single 9-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI 12-Slot BRIC Matrix, 15x32 1-Pole (3 sub-cards)
40-562B-321-15X32
Matrix Switch Module
The 40-562B-321-15X32 is a high density BRIC12 matrix module with a size of 15x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI MUX 4 Bank 0f 16 Channel 1 Pole
40-610-021-4/16/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
PCI High Voltage MUX
50-350-001
Multiplexer Module
The 50-350-001 is a Short PCI Card designed as a high voltage multiplexer for use in a Submarine Cable Testing Application. It is designed to allow the dynamic connection of various test instruments to 1 of 16 test points. The multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.
-
Product
4-Ch DPDT 10A-250VAC 24VDC Multiplexer
H62004900
Multiplexer Module
Up to 10A 250Vac 10mOhm Measurement Shunt Controlled via YAV90304 Form F
-
Product
NI-9207, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781068-02
Current Input Module
500 S/s, 16-Channel C Series Voltage and Current Input Module - The NI‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-01
Signal Module
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
Mini Coax, Module, ITA, 90 Series, 19 Position
510108111
ITA Module
Primary mating module 510104120. (May mate with other Receiver modules, as well.)
-
Product
PXI 8-Slot BRIC Matrix, 60x32 1-Pole (12 sub-cards)
40-562B-121-60X32
Matrix Switch Module
The 40-562B-121-60X32 is a high density BRIC8 matrix module with a size of 60x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
