-
Product
Test Fixture Adapters for In-Circuit Test Fixtures
-
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
Product
Pneumatic and Hydraulic Characteristics Test
-
Pneumatic and hydraulic testing is performed to demonstrate operating pressure, pressure drop, volume and flow parameters, as well as performance characteristics, of fluid system components and assemblies.
-
Product
8-Pin Pneumatic Block | Receiver Side
-
8-pin pneumatic block | receiver side, Equipped with KSV-PK-3 (462011), Grid dimensions 10-11mm / 12-13mm, 4mm hose, Plastic: With socket contact with shut-off HAN compressed air socket (278256)
-
Product
Custom Test Fixtures
-
Cortek Test Solution’s design capabilities range from very basic to extremely sophisticated solutions. Developing custom test fixtures demands more engineering time as well as an in-depth knowledge of mechanical design, pcb test methods paired with precision machining. Our experienced engineers will evaluate your requirement and design innovative mechanical test fixtures to meet your application needs in both the R & D and production environments.
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
Product
In-Circuit Fixtures
-
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
-
Product
Automatic Fixture Removal
S96007B
-
Automatic fixture removal (AFR), is the easiest way to remove fixture effects from non-coaxial device measurements.
-
Product
Pneumatic Type
-
Concentric Technology Solutions, Inc.
The Pneumatic Operation series of shield boxes provides superior performance for efficient RF isolation test environment for testing mobile, WLAN and other small RF devices. Its pneumatic controls to open and close the lid can be controlled manually or with a remote control for semi-automatic operation.
-
Product
Vacuum Test Fixtures
Series 63
-
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
Product
Function Test Fixtures
-
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
Product
Custom Fixtures
-
The shock and vibration fixture model BW-SV-3X3X3 is designed to accept up to 24 each of the TO-3 packages on each of the 6 axes and mount to the vibration shaker model BW-100C and Shock Tester model BW-E5000. The fixture is made of white derlin and measures 3”x3”x3”and weighs approximately 13 ounces. The fixture includes a white derlin cube with a 2 ¼” bolt circle and 4 10-32 x 3” cap screws.
-
-
Product
Cable Continuity Test Fixture
1000CCT
-
The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
Product
13-Pin Pneumatic Coax Block
-
13-pin pneumatic coaxial block, receiver side.Pneumatics:- Fitted with KSV-PK-4 (VGRCB-13 tyre)- 6mm hoseCoax:- (VGRCB-13C)- Voltage 250VAC- Current 5A- Contact resistance 39mΩ- Impedance 50Ω- Line resources 3.7Ghz (-3db)- Absorption capacity 8.8pf- Inductance 42mH- Resistance 25,000 cycles- Network connection SMB- Max. Power loss *: 25W
-
Product
ME2PWG-B, Pneumatic Unit
101506
-
The ME2PWG-B is a cutting-edge pneumatic unit from the ME2 series that showcases remarkable versatility and efficiency. This interchangeable system consists of the ME2PWG basic unit and the ME2PWK exchangeable cassette, making it a robust choice for a variety of applications. It incorporates an innovative auto-open function that facilitates both manual operation and an optional fully automated auto-open-close feature, ideal for use in restricted or secure environments. With an impressive opening angle of 90°, users can easily transition between manual control and robotic automation, enhancing operational flexibility and speed.
-
Product
Customized Test Fixtures
-
Test fixture is a device designed to mount a device under test (DUT), equipment under test (EUT) and unit under test (UUT) in place and allow it to be tested by being subjected to controlled electronic test signals and procedures.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg
-
Product
Fabric Pneumatic Bursting Tester
TF142C
-
TESTEX Testing Equipment Systems Ltd.
Fabric Pneumatic Bursting Tester, to determine the bursting pressure of fabrics uses pneumatic test method, including knits, woven fabric, non-woven fabric, laminated fabric and other craft-made fabric.A test specimen is clamped over an expansive diaphragm by a circular clamping ring, increasing compressed air pressure is applied to the underside of the diaphragm, causing distension of the fabric until the test specimen bursts, the bursting strength and distension are determined.
-
Product
Magnetizing Fixtures
-
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
Product
Pneumatic Units
-
Astronics PGA’s Pneumatic Unit enables you to provide a complete set of comforts in your upscale airplane seats. Adjustable firmness levels plus massage features ensure passengers feel pampered while enjoying the amenities of the flight.
-
Product
Clamshell Type Mechanical Fixtures
Series 30
-
Semco’s GR Series 30 mechanical kits are an inexpensive solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility.
-
Product
Hand Held Test Fixtures
-
Manual, or semi-automated mechanical devices designed to secure a Device Under Test (DUT) and provide a stable interface for electrical testing, inspection, or programming.
-
Product
EBIRST 78-pin D-type Verification Fixture
93-006-101
Verification Fixture
The 93-006-101 78-pin D-type Verification Fixture is an accessory for the eBIRST range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces switching solutions. The tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
Product
Fixture Building Software
FixGenius
-
Tests show that FixGenius’ rule-based probe-mapping algorithms reduce pin deflection by up to 25% compared with traditional fixturing packages. FixGenius comes with a powerful Fixture Editor that allows the user to change the probe mapping. If a solution is mathematically possible, FixGenius’ algorithms will find it, and pick the one with least deflection. If the job simply cannot be done with one single fixture, FixGenius will fully automatically split the test into multiple fixtures or into fixture and flying probe test sets, with guaranteed test integrity.
-
Product
Latch-on Test Fixtures
-
Latch-on Test Fixtures provide a convenient way for production personnel to quickly and reliably make electrical connections to a product for programming or final test. These custom fixtures eliminate the need to hand-wire products in order to power them up and communicate with them. Typical applications for latch-on test fixtures are metering devices, control panels, and any type of controls that connect via terminal strips.
-
Product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
Product
Low Freq. Pneumatic Levelling Mounts
-
ACE has a range of low frequency pneumatic levelling mounts under the designations PLM and PAL: they keep high performance and precision machines isolated from vibrations, impacts and force peaks, e.g. from high performance and precision machines, at bay.
-
Product
Pneumatic Contacts
-
VPC offers a range of pneumatic contacts that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.
