PCI-X
an extended PCI bus with signaling speeds up to 4.3 gigabytes per second of bandwidth.
See Also: PCI extended, PCI
-
product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
PCI-X Carrier For AMC Modules
PCI102
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
product
32/64b 33/66 MHz PCI-x to PMC-x Adapter
8098a
The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot while providing a migration path for PCI-X board suppliers to port their products to a PMC-X form factor.
-
product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X-FC4 Simulyzer
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
product
Test & Simulation Interface for PCI-X
PCI-X-C1760
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI-X
-
product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Multifunction Analog I/O Card
LPCI-AIO16A
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
product
Multiprotocol Serial Card
LPCI-COM-8SM
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis. The cards are 6.6 inches in length and 2.21 inches seated height and may be installed in any 3.3 or 5-volt PCI or PCI-X expansion slot.
-
product
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter
4044
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter. The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot. It provides a migration path for PCI-X board suppliers to port their products to a PMC-X form factor. As the PMCX equivalent board is developed, software development and migration can proceed with the original PCI-X board operating in a PMC-X environment.
-
product
Virtex-5 FPGA with Plug-in I/O
PMC-VFX
Acromag’s PMC-VFX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules.
-
product
Virtex-5 FPGA with Plug-in I/O
PMC-VSX
Acromag’s PMC-VSX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules. The result is a powerful and flexible I/O processor module that is capable of executing your custom instruction sets and algorithms.
-
product
PCI Extender Card for cPCI Systems
DP-cPCI-7497
The DP-cPCI-7497 is highly flexible PCI Extender card, which can be used to extend PCI / PCI-X bus from one system to another system over an optical fiber medium upto 500m distance. A PCI-X to PCI-e Bridge is used to convert the PCI / PCI-X protocol to x4 PCI Express protocol operating at 2.5Gbps.The PCI-X to PCI-e Bridge is connected to four optical transceivers (x4 PCI- e link) which can transmit optical signals upto 2.5Gbps speed.A x4 copper medium connection option in lieu of optical transceivers is also available.
-
product
1 PICMG® CPU, 1 PCI-E® x16,1 PCI-X™, 2 PCI™ Slots Backplane
EBP-5E1
- Segment: 1- Slots:1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-X™, 2 PCI™- Support ATX power supplies- Dimension: 153 mm x 330 mm
-
product
AMC For PCIe Bus Expansion
AMC113
AMC113 is VadaTech second generation PCIe expansion module. The AMC113 is a high-speed 20Gbps bridge from the host PCIe bus to VadaTech’s other carrier and Rear Transition Module (RTM) products such as the ATC104/114/118/117/119, ART114, μTCA chassis, etc. The different carriers host different I/O modules such as PMC/PrPMC, AMC, PCI-X and PCIe edge modules. This concept allows any of the available I/O modules in these standard form factors to be integrated quickly and easily into an AdvancedTCA or μTCA subsystem.The AMC113 allows expansion among multiple μTCA chassis or
-
product
PCIe Adapter for PMC
PCIe4LBPCI
Now you can use your PCI with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. PCIe4LBPCI ( PCIe Bridge PCI 1 position) adapter / carrier converter card provides the ability to install one PCI card into a standard PCIe (Express) 4 lane slot. Suitable for PCI or PCI-X operation with the PCI; 32 bit or 64 bit data and PCI (25, 33, 50, 66) or PCI-X (50,66,100,133) MHz. clock. Auto selected or switch programmable speeds. The bridge can operate with 1, 2, 3 or 4 lanes active, and can be installed into slots with more than 4 lanes if desired.
-
product
6U Dual 64/100 PMC VME Carrier
V2PMC2
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Spartan-6 FPGA Modules with Plug-In I/O
PMC-SLX
Acromag’s cost-effective PMC-SLX modules feature a user-configurable Xilinx® Spartan®-6 FPGA enhanced with high-speed memory and a high-throughput PCI-X interface. Field I/O interfaces to the PMC FPGA via the rear J4/P4 connector and/or with optional front mezzanine AXM plug-in I/O modules. The result is a powerful and flexible I/O processor module that is capable of executing custom instruction sets and algorithms.
-
product
Network Interface Card
PMC-GBIT-DT2BP
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
AFDX® / ARINC 664 Test And Simulation PCIe Module
PCIe-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
XMC Module Carrier PCI Express x 8
SK4-WALTZ
SK4-WALTZ is a bidirectional 8-lane PCI Express® Gen3 redriver, for optimum high speed signal integrity, and should be installed into a fat pipe peripheral slot of a CompactPCI® Serial backplane.
-
product
PCI To PCI Express Board
MS 1718
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
PCI and PCI-X Bus Analyzer / Exerciser
PCI850
The PCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
Digital Input/Output and Counter/Timer Card
PCI-DIO-96C3
This is a 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length 5V PCI-bus (or PCI-X bus) slot in X86 type PC’s.
-
product
32/64-Bit 33/66 MHz PCI-X-to-PMC-X Adapter
4068
The Technobox, Inc. P/N 4068 PCI-X-to-PMC-X Adapter permits operation of a standard 32- or 64-bit PCI-X card in a PMC-X slot. It provides a migration path for PCI-X board suppliers to port their products to a PMC-X form factor. As the PMCX equivalent board is developed, software development and migration can proceed with the original PCI-X board operating in a PMC-X environment.
-
product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X FC4 Simulyzer
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. With a simple firmware/software upgrade, a single function board can become a full function board without having to purchase new hardware.
