Audio Amplifiers
This topic is for test equipment that is designed for the testing of audio amplifiers.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Driver Amplifiers
-
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
Product
Low Noise Amplifier
-
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
RF Amplifiers up to 500 MHz
-
Narrow and Broad band RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAsFET in Class A and Class A/B topologies for AM, FM, VHF, and UHF bands with output power ranging from 0dbm to 60dbm.
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3PCI
-
The AAF-3PCI is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier PCI bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
Product
Audio Level Analyzer
BK3011C
-
In keeping with our goal of constant improvement, we have upgraded our BK3011 MEMS mic tester! The BK3011C is more modular, easier to connect and with the new Test Shop upgrade, easier to use. But the basic features are still the same. Then BK3011C enables you to check mic characteristices over a frequency range using a stable, constant SPL sweep. It still produces both graphs and numerical data but now will automatically classify both PASSing and FAILing DUT's so you can keep track of quality issues and trends.
-
Product
mAEStro Digital Audio Re-Clocking Distribution Amplifier
-
The mAEStro ADA-100 receives AES/EBU (AES3) or S/PDIF digital audio and provides four re-clocked digital audio outputs. It automatically detects sample rates from 32kHz to 96kHz with low-jitter clock recovery. The outputs are completely regenerated using a jitter-free clock that is locked to the source input. The rugged self-contained metal enclosure has a number of mounting options from desktop, to rear side-rail rack mounting, to ganged front-side or rear-side rack mounting.
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
Four Quadrant Power Amplifier For Simulation Applicaton
PAV30000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Measuring Amplifiers
-
Smart force measurement with a parameterizable measurement amplifier.
-
Product
Ultra-low Noise High Voltage Amplifier
WMA-200
-
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
-
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
Product
Portable Power Amplifier
PAV120Bip
-
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
Product
Digital Quad-channel High-Frequency Lock-In Amplifier -
eLockIn 205
-
Being the top model eLockIn series, the eLockIn205/2 offers a very fast TCP/IP connection, ultra-fast DAC outputs of the measured signals and all signals supplied at BNC connectors.
-
Product
SOA & Raman Amplifier
-
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
Product
Operational Amplifier
Op Amp Series
-
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
Product
The SoundCheck Amplifier
SCAmp Audio Test Amplifier
-
SC Amp is the world’s only dedicated audio test amplifier. Specifically designed for the audio test market, it incorporates several features unique to the needs of audio test and measurement, and unnecessary features found in regular audio amplifiers have been eliminated to keep production line operation simple and error-proof.
-
Product
High Speed High Voltage Amplifier
WMA-300
-
The WMA-300 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-300 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications. Two WMA-300 amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
EDFA Amplifier
-
A line of Gain Flattening Erbium-Doped Fiber Amplifiers are designed for in-line amplification of DWDM networks. When a standard EDFA is used to amplify multi-channel DWDM signals, the output power level of various channels will vary according to the gain profile of the erbium fiber. This gain variation can be as great as 6 dB in magnitude. The EDFA-GB-R is unique in its dual-stage amplification and internal Gain Flattening Filter (GFF) to compensate the erbium fiber gain variation.
-
Product
3-5 Watt Power Amplifiers
CCM1095 and CCM2096
-
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.
-
Product
Low Noise Amplifiers
-
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
-
Product
Amplifiers
-
Elbit Systems of America’s secure networks and communication solutions provide warfighters secured and reliable radio communications for most operational applications. Our teams work hard to deliver a number of scalable options from extremely rugged to standard industrial or commercial specifications. Our family of Single-Channel and Dual-Channel Modular Power Amplifiers operates with current and next-gen radios and offer lightweight, compact solutions on most platforms. The modular design simplifies maintenance, provides customer flexibility, and accelerates the fielding of new capabilities.
-
Product
DSP Dual Phase Lock-In Amplifier
SR850
-
Stanford Research Systems, Inc.
The SR850 is a digital lock-in amplifier based on an innovative DSP (Digital Signal Processing) architecture. The SR850 boasts a number of significant performance advantages over traditional lock-in amplifiers?higher dynamic reserve, lower drift, lower distortion, and dramatically higher phase resolution.
-
Product
Audio Test Tone Generator
Tone Plug
-
The TONE PLUG offers five user selectable sine wave test tones at frequencies of 100, 250, 400, 1K and 10KHz. An additional 5 special function test signals are also provided.
-
Product
4-Channel Strain Gage Amplifier Module for the SCS-800 Signal Conditioning System
SCS-824 Series
-
The SCS-824 series provides 4 channels of strain gageinputs for the SCS-800 signal conditioning system. TheSCS-824 series interfaces all strain gage types, fromsingle-element quarter bridges to 4-element full bridges
-
Product
GaAs pHEMT MMIC Power Amplifier, DC - 28 GHz
HMC994APM5E
-
The HMC994APM 5E is a GaAs pHEMT MMIC Distributed Wideband Power Amplifier which operates between DC and 28 GHz. The amplifier provides 15 dB of gain, +29 dBm of saturated output power, and 25% PAE from a +10V supply. With up to +38 dBm Output IP 3 the HMC994APM 5E is ideal for high linearity applications in military and space as well as test equipment where high order modulations are used. The HMC994APM 5E exhibits a positive gain slope from 2 to 20 GHz making it ideal for EW , ECM, and test equipment applications. The HMC994APM5E amplifier I/Os are internally matched to 50 Ohms and is packaged in a leadless QFN 5x5 mm surface mount package.
-
Product
High Voltage Linear Amplifier
A800X
-
This unit is a version of A800 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A800X functionally identical with A800 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
