Trigger Modules
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 925Ω
40-298-021
-
The 40-298-021 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 12-Slot BRIC Matrix, 90x32 1-Pole (18 sub-cards)
40-562B-321-90X32
-
The 40-562B-321-90X32 is a high density BRIC12 matrix module with a size of 90x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
EN50155 Managed PoE Ethernet Switch
EKI-9528E-8GMPX
-
M12 connector with ruggedized IP54 certified housing, Complies with EN50155 and EN50121-3-2 standards, 24 x PoE IEEE802.3af/at ports, Wide nominal power input range: 24 ~ 110VDC. Operating power input range: 16.8 ~ 137.5VDC, X-Ring Pro delivers rapid and predictable convergence.
-
Product
PXI 2A Multiplexer, 1-Bank, 8-Channel, 16-Pole
40-614B-019
-
This 1-bank, 8-channel, 16-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
-
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
Coax/20-26 GHz/ 75 Ohm HD, Module, Receiver, iCon Series, 18 Position
510160114
-
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161114. (May mate with other ITA modules, as well.)
-
Product
PXI/PXIe RF Multiplexer, Dual 6-Channel, Terminated, 8GHz, 50Ω, SMA
40-881B-002
-
The 40-881B-002 (PXI) and 42-881B-002 (PXIe) are dual 6 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. It is available as a single or dual MUX in one and two slots respectively.
-
Product
PXIe System Module: Single Port (x8), Gen 3
M9022A
-
The M9022A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The module can also be used with an M9037A PXIe embedded controller to interconnect two chassis in a multi-chassis system.
-
Product
NI-9212, 8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module
782975-01
-
8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module - The NI‑9212 offers channel‑to‑channel, isolated thermocouple input channels. The NI‑9212 channel‑to‑channel isolation protects channels from continuous voltages up to 250 Vrms and transient (withstand) voltages up to 1500 Vrms. You can use the NI‑9212 in a variety of applications that are not conducive for bank-isolated channels such as white goods testing, in-vehicle data logging, battery stack testing, as well as in various other noisy industrial environments.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm
50-293-013
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Triple SP4T Multiplexer 6GHz 50 SMA
40-784A-103
-
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 48-Pole
40-571-004
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Vacuum-Pneumatic, Module, Receiver, 90 Series, 1 Pos Vacuum, 2 Pos 3/8" ID Pneumatic
510104276
-
Primary mating module 510108264.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm - SPST
50-294-122
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Universal Counter/Timers
-
This line of high-precision universal counter/timers delivers the ultimate in reliability for your application.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 67GHz, 50Ω, SMA-1.85
40-785C-473-E
-
The 40-785C-473-E (PXI) and 42-785C-473-E (PXIe) are triple SP4T 67GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
16-Ch SPST 10A-277VAC High Current
YAV90086
-
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
PXI Resistor Module 4-Channel 1R to 63.7R
40-293-011
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Solid State MUX, 4 pole, 40 channel
40-680-404
-
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
-
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
PXI 8 Slot BRIC 352x4 2-pole (8 sub-cards)
40-562A-122-352X4
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 11.4MΩ
40-251-153
-
The 40-251-153 is a programmable resistor module with 1 channel which can be set between 3Ω and 11.4MΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 3x3 10GHz Matrix
40-787-518-3X3
-
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
-
Product
Single 32x6 1-Pole High-Density PXI Matrix Module
40-520-301
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm With SPDT
50-293-112
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 472Ω
40-298-120
-
The 40-298-120 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 6GHz, 50Ω, SMA
40-784B-001
-
The 40-784B-001 (PXI) and 42-784B-001 (PXIe) are single SP6T 6GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI 8 Slot BRIC 192x12 2A 1-Pole Matrix
40-597-106
-
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 1.51MΩ
40-251-150
-
The 40-251-150 is a programmable resistor module with 1 channel which can be set between 3Ω and 1.51MΩ with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 22 GHz, 50 Ω, SMA, Failsafe
42-788-131
-
The 40-788-131 (PXI) and 42-788-131 (PXIe) are single failsafe SP10T 22 GHz unterminated microwave multiplexers. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
