Trigger Modules
-
Product
PXIe-6674T, OCXO PXI Synchronization Module
781037-01
Timing and Synchronization Module
PXIe, OCXO PXI Synchronization Module—The PXIe‑6674T generates and routes clocks and triggers between devices in a PXI Express chassis as well as to other PXI and PXI Express chassis or third-party instrumentation. The PXIe‑6674T unlocks the advanced low-voltage differential signaling (LVDS) trigger signals PXIe‑DStarA, PXIe‑DStarB, and PXIe‑DStarC, on PXI Express while fully supporting the PXI trigger lines. The PXIe‑6674T can generate two types of clock signals: a highly stable 10 MHz clock based on an onboard precision oven-controlled crystal oscillator (OCXO) reference and a second clock from the direct digital synthesis (DDS) clock generation circuit.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
Voltage Input Module
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
Product
PXI 2 Slot BRIC 45x16 1-Pole (3 sub-cards)
40-561A-221-45X16
Matrix Switch Module
The 40-561A-221-45X16 is part of a range of high-density PXI BRIC matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
EN50155 Managed Ethernet Switch
EKI-9528E-8GMX
Ethernet Switch Module
M12 connector with ruggedized IP54 certified housing, Complies with EN50155 and EN50121-3-2 standards, Wide nominal power input range: 24 ~ 110VDC. Operating power input range: 16.8 ~ 137.5VDC, X-Ring Pro delivers rapid and predictable convergence, Leverages IXM technology to ease maintenance.
-
Product
PXI 12-Slot BRIC Matrix, 704x4 2-Pole (16 sub-cards)
40-562B-322-704X4
Matrix Switch Module
The 40-562B-322-704X4 is a high density BRIC12 matrix module with a size of 704x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 2A Multiplexer, 4-Bank, 16-Channel, 2-Pole
40-614C-007
Multiplexer Module
This 4-bank, 16-channel, 2 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 8 Slot BRIC 210x8 1-Pole (7 sub-cards)
40-561A-121-210X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
NI-9485, 8-Channel, SSR Relay, 60 VDC/30 Vrms, 750 mA C Series Relay Output Module
779600-02
Relay Output Module
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 50 GHz, 50 Ω, SMA-2.4, Terminated, Failsafe
42-785C-451-T
Multiplexer Module
The 40-785C-451-T (PXI) and 42-785C-451-T (PXIe) are single failsafe SP4T 50 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
783864-02
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-035
Programmable Resistor Module
The 40-254-035 (PXI) and 42-254-035 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 201kΩ with 4Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI Solid-State Matrix Module, 6x2, 10 A
40-553A-011
Matrix Switch Module
The 40-553A-011 is a high current 6x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each matrix switching path can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 8-Slot BRIC Matrix, 138x8, 1-Pole (3 sub-cards) Dual Bus
40-560B-121-138X8-M
Matrix Switch Module
The 40-560B-121-138x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
Product
PXI 20 Banks of 4 Channel 2 Pole MUX
40-615-022-20/4/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
8-Sites ISP & I2C/SPI Interface
YAV90ISP
Switch Module
Industrial Programmers Interface up to 8 targetsRelay BarrierDemultiplexer module up to 32 devicesCommunication Interfaces I2C and SPI
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 6.97kΩ
40-298-024
Programmable Resistor Module
The 40-298-024 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 8 Slot BRIC 90X16 1-Pole (6 sub-cards)
40-561A-121-90X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI Microwave Multiplexer, SP4T, 3-Bank, 26.5GHz, 50Ω, SMA, Terminated
60-803-303
Multiplexer Module
High performance RF multiplexer suitable for switching microwave signals up to 26.5GHz with automatic termination of unused signals
-
Product
PXI Prototyping Module, 1-Slot, 15-Pin D-Type
40-225A-601
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI 12-Slot BRIC Matrix, 165x16 1-Pole (15 sub-cards)
40-562B-321-165X16
Matrix Switch Module
The 40-562B-321-165X16 is a high density BRIC12 matrix module with a size of 165x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Electronic Calibration Module (ECal), 67 GHz, 1.85 Mm, 2-Port
N4694D
Electronic Calibration Module
The Keysight N4694D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4694D is a precision 2-port ECal module that supports 1.85 mm connectors up to 67 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4694D is included for securing your ECal module and accessories.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 472Ω
40-251-020
Programmable Resistor Module
The 40-251-020 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 8-slot BRIC Power Multiplexer, 6-Channel, 24-Pole (5 Sub-cards)
40-571A-103
Multiplexer Module
The 40-571A-103 is a 6-channel, 24-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-144
Precision Resistor Module
The 40-297A-144 (PXI) and the 42-297A-144 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 1.51 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 18GHz, 50Ω, SMA
40-784B-023
Multiplexer Module
The 40-784B-023 (PXI) and 42-784B-023 (PXIe) are triple SP6T 18GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI 4-Slot High Density 2A BRIC Matrix, 58x8 2-Pole (2 Sub-cards)
40-573-002-58X8
Matrix Switch Module
The 40-573-002-58x8 BRIC is part of a range of high density matrix modules able to switch up to 2 A at 240 VDC/250 VAC. They are available in 2, 4 or 8-slot sizes to suit most high performance matrix requirements, constructed using quality electromechanical relays for high switching confidence.
-
Product
PXI Dual SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-001
Switch Module
The 40-880A-001 is a dual SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
Product
PXI High-Density RF Multiplexer: 3 GHz, 1 x 16, 50 Ω
M9149A
Multiplexer Module
Route signals up to 3 GHz through a 1 x 16 RF switch multiplexer in a single PXI module.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, LC Connectors
42-852A-418
Multiplexer Module
The 40/42-852A-418 is a PXI/PXIe 8-channel multiplexer with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
