Programmable Loads
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
High Power LED DC Electronic Load
33430G Series（1800W / 3600W）
Each 33430G Series has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, panel with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
product
Programmable Modbus Simulator
ModMultiSim
ModMultiSim is a programmable Modbus simulator that enables realistic simulation of multiple Modbus slaves in their environment. Connect your Modbus masters to ModMultiSim, instead of real Modbus slave devices, in order to test and configure the masters.
-
product
Open-Short-Load RF calibration kits
Open-Short-Load RF calibration kits from Fairview Microwave are available with Type N or 7/16 DIN connectors. Type N open-short-load RF calibration kits have male or female genders, 7/16 DIN open-short-load kits are male gender. Type N open-short-load (OSL) calibration kits for RF have a minimum frequency of 0 (DC) and a maximum frequency range between 4 GHz and 6 GHz. Type N open short load kits for calibration have a maximum power handling of between 1 Watt and 2 Watts.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
10 Gb/s Programmable Digital Delay Line
QPDDL10
The QPDDL10 series delay lines are four channel precision time delay generators for digital signals. Delays are controlled precisely in 5 ps increments at data rates up to 10 billion bits per second or clock rates exceeding 5 GHz. Each of the four channels is independently programmable.
-
product
110V / 90 Amp Load
EL12-110M
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 110V Rectifiers and Power Supplies with output Voltages in the range of 100V to 135V and is extremely cost effective.
-
product
DC Electronic Loads
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
NGI DC Electronic Loads
-
product
Miniature S-Beam Load Cell
500 Series
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
product
Robotic Sample Loading Systems
Below you can see examples of two systems using our robotic sample loading system. Many other automated microscopy systems are possible using our components.
-
product
Electronic Loads
Electronic loads are indispensable tools in several fields of electrochemistry, for example in the research of batteries and fuel cells. Using an additional external power supply you easily can extend an EL to a two-quadrant potentiostat you need e.g. in the field of electrolysis.
-
product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
product
AC Load Banks
XL500-XL600 Series
Mosebach Manufacturing Company
The XL500-XL600 Series load banks offer you a continuous load at various voltages in a compact, lightweight enclosure.
-
product
Load Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
Load Measurement Trainer comprises of strain gauge based load cell,loading arrangement to load in compression, weights and digital load indicator to read the load in Kg.
-
product
Dummy Load
Dummy load is capable of dissipating four times the legal limit 6 kW for 2 minutes and legal limit 1500 watts key down, forever. It covers the 160 meter to 6 meter bands (actually 1 Mhz-60 MHz continuously). It is a dry dummy load intended for testing amplifiers and station conditions. Two fans on the rear of the unit are automatically turned on when the internal temperature reaches 120°F/49°C . The unit runs off a universal AC supply. Simple to operate and use, the dummy load includes an RF sample output of -60 dBc.
-
product
Load Cell Junction Box
SY-JUNCTION-IP67
The SY-JUNCTION-IP67 load cell junction box is useful to parallel connection of load cells and take just one cable out to almost any indicator, either batch controller or a PLC.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 2Ω to 6.97kΩ
40-253-030
The 40-253-030 is a programmable resistor module with 1 channel which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Universal Programmers
Uprog
Uprog is universal device programmers family. It uses LPT parallel port or USB for communication with PC.Graphical interface of Uprog software is very confortable in usage for programming and testing tasks. Uprog programmers have 100% universal programming socket. They allow to put independly on any pin programming voltage (0-30V), power supply (1.8-8V), ground or clock, so this flexibility allow Uprog programmers to handle any device.
-
product
Programmable AC/DC Withstanding Volatge And Insulation Tester
RK-7122
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC withstanding volatge and insulation tester
-
product
6, 8 GHz, 4 Channel Programmable Attentuator
QPA8, PA8
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
product
Signal Converters & Load Cell Signal Converter
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
product
Air Core Line & Load Reactors
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
product
PXI Precision Resistor Module 9-Channel, 2 to 26.7k
40-297-032
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Unclamped Inductive Load Tester
ITC55300C
Model ITC55300C performs ruggedness testing of power MOSFETs, discretes and modules and IGBTs, discretes and modules. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
product
DC-14GHz Divide-by-8 to 511 Programmable Integer Divider
UXN14M9P
The UXN14M9P is a highly programmable integer divider covering all integer divide ratios between 8 and 511. The device features single-ended or differential inputs and outputs. Parallel control inputs are CMOS and LVTTL compatible for ease of system integration. The UXN14M9P is packaged in a 40-pin 6x6mm leadless plastic surface mount package.
-
product
Battery Load Bank
K-3980
Kongter Test & Measurement Co., Limited
Kongter offers a series of customized DC load banks with many different models for constant current battery discharge test and battery capacity test. They cover a wide voltage range from 12V to 480V nominal voltages with current up to 600A. They are widely applied in various industries. With its optional battery Data Acquisition Case (DAC), discharge values of EACH cell could be monitored in battery load bank and PC software simultaneously by using Kongter’s data view software.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-156
The 40-297A-156 (PXI) and the 42-297A-156 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 85.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Programmable Sensor Module With CAN Connection
PCAN GPS
The PCAN-GPS is a freely programmable sensor module for position and attitude determination. It has a satellite receiver, a magnetic field sensor, an accelerometer and a gyroscope. The recorded data can be transmitted on a CAN bus and logged on the internal memory card. The data is processed by a microcontroller from the NXP LPC4000 series.
-
product
Bench Electronic Loads
EL30000 Series
The Keysight EL30000 Series Bench electronic load with a built-in data logger provides new levels of test insights for your devices like power supplies, batteries, DC to DC converters, and more. View voltage and current trends to make real-time decisions, rather than waiting hours for a test to complete. At the heart of the EL30000 is a highly accurate measurement system that provides real-time updates to the large display. Keysight’s PathWave BenchVue software allows you to operate the electronic load remotely, execute test sequences, log data, and integrate with other test instruments. Single and dual-channel models are available with up to 600 W for measurements that require more power. Start your test with confidence and finish with results you trust.
-
product
Programmable Controllers
Panasonic Automotive & Industrial Systems Europe GmbH
The Panasonic product portfolio comprises both low-cost compact programmable controllers with little space requirement which are suitable for many basic tasks and high-end PLCs like the flagship FP7.A multitude of useful functions has been successfully integrated into the compact PLCs so that they offer many of the advantages of a modular high-end PLC such as analog control, network communication, and positioning control. All Panasonic PLCs offer an outstanding price-performance ratio.
