-
product
Portable Solar Reflectometer
CONDOR
Condor is a portable reflectometer designed for field measurement of reflectivity in the solar field in less than 10 seconds with a high accuracy and precision. It can be applied to both flat and curved reflecting surfaces of up to 4 mm thickness.
-
product
Sound Level Meter & Real-time Analyzer
824
The Larson Davis System 824 combines advanced sound level meter and real-time analyzer capabilities into a rugged, user-friendly, ergonomic package. The base unit is an Integrating Sound Level Meter (ISM) that meets Type 1 Standards and offers simultaneous measurement of sound pressure levels using fast, slow, and impulse detectors, for A, C, and flat frequency weightings. This feature, termed ANY LEVEL™ measures 48 sound pressure parameters at once with a linear, 105 dB range. With firmware enhancements, the base unit expands as needed to accommodate multiple data processing requirements
-
product
Solvent Resistance Tester
NRJ-100
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.10-2008Used to detect the solvent resistance performance of enameled round wires and flat wires with nominal conductor diameter above 0.250mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Pencil push unit would automatically lay down pencil and move ahead, lift pencil and automatically return to initial position;Used in combination with JRK-60 solvent thermostatic controller;Automatic pencil sharper can sharpen pencil tip to be 60° symmetrical to its axis;
-
product
Pyranometer
SR15-A1
Hukseflux Thermal Sensors B.V.
SR15-A1 is a high-accuracy solar radiation sensor. It is” First Class” according to the ISO 9060:1990 standard and “Spectrally Flat Class B” in the 2018 revision. With its on-board heater, it is compliant in its standard configuration with the requirements for “Class B” PV monitoring systems of the new IEC 61724-1:2017 standard. SR15-A1 measures the solar radiation received by a plane surface from a 180 o field of view angle.
-
product
VOA DWDM with EDFA With VOA, EDFA Dense Wavelength Division Multiplexer
DWDA-1000 (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDA-1000 series is integrated by DWDM, VOA and EDFA module in a 1RU or 3D rack. Each channel of DWDM with a high-resolution factor electronic control adjustable optical attenuator will adjust and equilibrium the power. The insertion loss, power loss because of the channel equilibrium of DWDM will be amplified and compensation by the build-in gain flatness EDFA. Compact and simple device structure, thereby reducing the connections between devices to improve the index and reliability of the system. Can be used in DWDM system power equilibrium, optical add and drop multiplexed (OADW) flexible and expediently.
-
product
Non-contact Inline Sheet Resistance Measurement Module For Flat Panel Display
NC-600
*Non-stop and non-contact sheet resistance measuring of thin film on glass runs through on conveyer*1 to 10 number of probe by sizes of glass is attachable*Glass collision prevention function*Continuous test data report to the host computer
-
product
RC68-68, Ribbon Cable, 68 D-Type to 68 VHDCI Offset, .5 Meter
187252-0R5
68-Pin Female to 68-Pin Female, 1 Ribbon Connection Ribbon Cable - The R68F-68F Cable, sometimes referred to as the R68-68 or RC68-68, is a flat ribbon cable that connects to 68-pin NI data acquisition or digital I/O devices. The R68F-68F Cable is offered in different lengths and with D-SUB or VHDCI front end connectors.
-
product
(125×150×20mm) C-Band DWDM Line EDFA Module
WLA4200-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WLA4200-FM05 series is a gain flatness line EDFA Module which is specifically designed for C-Band 44 channels optic transmission system. It adopts the most excellent optical performance, the most advanced electronic control technology and the most complete software functionalities; it is featured with wide working wavelength range, low noise and excellent gain flatness. WLA4200-FM05 is mainly installed in middle of transmission line, replacing the traditional relay, to compensate the optical power loss in the line and extend the optical signal transmission distance
-
product
Semiconductor Metrology Systems
MTI Instruments'' semiconductor wafer metrology tools consist of a complete line of wafer measurement systems for virtually any material including Silicon wafer (Si), Gallium Arsenide wafer (GaAs), Germanium wafer (Ge) and Indium Phosphide wafer (InP). From manual to semi-automated wafer inspection systems, the Proforma line of wafer metrology inspection tools is ideal for wafer thickness, wafer bow, wafer warp, resistivity, site and global flatness measurement. Our proprietary push/pull capacitance probes provide outstanding accuracy throughout their large measurement range, allowing measurement of highly warped wafers and stacked wafers. MTII''s solar metrology tools include off line manual systems for wafer thickness and Total Thickness Variation (TTV), as well as, in-process measurement systems capable of measuring wafer thickness, TTV and wafer bow at the speed of 5 wafers/second.
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
ITC Style VXI Module Shield Kits
* Box design for C-size ITC style PC Boards with 11 slots on their sides.* Pre-machined flat front panel with ejector handle cutouts.* Side shields include 0.375 inch wide vent slot on top and bottom sides for maximum cooling.* Shroudless design fits all VXI chassis.* Each kit includes side shields, front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.* Complimentary layout support includes PCB design template and CAD layout files.
-
product
Compact Infrared Thermometer With Laser Targeting
PIRT25
Unique Flat SurfaceMini-Modern Housing DesignSimple One-Handed OperationLaser TargetingLCD With BacklightCelsius or Fahrenheit ModesLaser On/Off SwitchAutomatic Power OffDisplay Hold FunctionMax/Min FunctionTemperature Range: -50 to 380 Celsius, -58 to 716 FahrenheitTemperature Resolution: 0.1Emissivity: Fixed at 0.95Optical Resolution: 8:1 Distance to Spot Size RatioBasic Accuracy: +2% of Reading or +2 C / +4 FResponse Time: <1 Sec.Diode Laser: Output <1mW @ 630-630nm, Class 11 LaserSpectral Response: 6-14umPower Supply: 9V BatteryDimensions: 7.09' H x 3.94' W x 1.81' DWeight: 5.6 oz.
-
product
Laser Head
5517D
The Keysight 5517D is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
High Current / High Voltage Pulsers
DEI Division
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
product
FPD Tester Model
27014
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
-
product
Test Connector Components
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
product
10 dB V-Band Waveguide Directional Coupler for Test Labs
SWD-5038531040H-15-SB
ModelSWD-5038531040H-15-SB is a V band, three-port waveguide directional coupler that delivers a 10 dB nominal coupling level and 30dB minimum directivity across the full waveguide band from 50to 85GHz. The three-port coupler uses a traditional multi-holeand split block design to achieve a flat coupling level, high directivity, and low insertion loss. The interfaces of the coupler are WR-15waveguides with UG-385/Uflanges. Custom coupling levels are available under different model numbers.
-
product
H.V. Probe Meter
PD-40AM
Standard Electric Works Co., Ltd
● Measures positive polarity DC voltages up to 40kV.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.
-
product
Directional Couplers
Virginia Diodes offers a broad range of millimeter-wave directional couplers for various applications. VDI directional couplers offer low insertion loss, coupling flatness and high directivity. Custom directional couplers may be available upon request. Contact VDI for more information.
-
product
Cross Hatch Adhesion Tester
1542
The Elcometer 1542 Cross Hatch Adhesion Tester is ideal for measuring the cross hatch adhesion of coatings up to 250µm (9.8mils) on flat surfaces and test panels.
-
product
Pressure Switches
INELTA Sensorsysteme GmbH & Co. KG
The mechanical pressure switch is available in steel or brass housing design and offers this special features:* robust and low cost* different adjustable rangesup to 50 bar* different pressure fittings* switched voltage up to 48 VDC* kind of contact: norm open, norm closedn flat connector 6,3 x 0,8 mm* cycles of pressure up to 106
-
product
Benchtop Amplifiers
Benchtop, broadband driver amplifiers are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a high output power and a superior gain flatness and low noise performance. The standard offering focuses on general purpose applications and covers the frequency range of 1 to 110 GHz. However, custom designs are also offered to meet any user’s specific needs.
-
product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
product
DH Series PT Browser Tip, 16 GHz BW, 3.5 Vpp Range
DH-PT
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Subminiature USB Cameras 5 Mpix Or 18 Mpix
*Smallest dimensions: 15 x 15 x 8 mm, 5 grams*5 Mpix,*New model with 18 Mpix*Minimal power consumption (under 1 Watt) beneficial for UAV / UAS*USB flat ribbon flex cables ideal for Embedded vision systems*GenICam/GenTL, C/C++, Python, .NET*Windows, macOS, Linux, ARM - NVIDIA Jetson TX2 and AGX Xavier*Board level available for OEM and customization
-
product
20 GHz Differential Probe with ProLink Interface
DH20-PL
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Gear Teeth Hardness Tester
PHT-1740
This dedicated unit is designed to test gear teeth and other difficult to access applications. The 1740 is an economically priced hardness tester that is loaded with the same features found on the base 1700 version. The 1740 hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This instrument comes complete with a dedicated DL impact device, calibrated test block and rugged carry case.
-
product
Multi-phase Carbon and Water Determination
RC612
The RC612 quantifies the carbon and water present in various organic and inorganic samples, and identifies the source of several types of carbon content. The large diameter reaction tube supports moisture analysis on a variety of sample types including powders, flat strips, or sections of tubes.
-
product
Satellite Optical Receiver
SSR-15CW
Hangzhou Softel Optic Co., Ltd.
*Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using high linear PD*Output connected to 5 IN series satellite multiswitch*Build-in optical AGC function*Red-LED for power indication*Smaller size and easier installation
-
product
FLAT Antennas
CTG recently developed a new paradigm in linearly-polarized antennas called the Flat Lens Antenna Technology or ‘FLAT’. These antennas have directivities similar to conventional dual-ridge antennas, but in a much lighter and “flatter” package. They can be used as a direct replacement for conventional horns for a wide variety of applications. They are made using composites technology so are also rugged and are ideal for both indoor and out-door applications.
