Cables
See Also: Cable Assemblies, Cable
-
Product
ITA, I2 Micro ICon, 120/12 Position Hybrid
410130104
ITA
The i2 Micro iCon ITA is capable of holding up to 120 QuadraPaddle contacts and up to 12 Micro Power or Micro Coax contacts. Its sleek, 0.8” footprint increases the horizontal stackability. The 30 degree U-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 0.77 in. The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
-
Product
37-Pin D-Type Female Straight PCB HV
40-963-037-SF-HV
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
PMC-ExtendIO-II
-
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
Product
Cable Assembly with 2.4mm Male Connectors
Y1740A
-
The Y1740A is a flexible cable with excellent phase stability. This cable is recommended for accurate S-parameter measurements using the following Keysight vector network analyzers: Streamline Series VNA, M983xA/M980xA Series PXIe VNA, or M981xAS series PXIe Vector Component Analyzer (VCA).
-
Product
Cable Testers
CableJoG 256
-
The CableJoG 256 can test up to 256 individual connections of all manufacturers of connectors. This simple test instrument stores up to 12 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection
-
Product
Terminal Board With 100-Pin SCSI-II Connector For General Purpose Servo & Stepper
DIN-825-4P0
Terminal Board
- Supports specific servos & steppers by cable selecting- On-board connector type: 100-pin SCSI-II- Dimensions: 300 mm x 107 mm x 44 mm (W x L x H)
-
Product
ATE & Test Systems
-
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
Product
SparkFun Breakout
FT231X
-
Introducing the SparkFun FT231X Breakout board, complete with the full UART hardware handshake feature! The pin-out of this board matches the FTDI cable to work with official Arduino and cloned Arduino boards. It can also be used for general serial applications.
-
Product
78-Pin D-Type Male Straight PCB Mount
40-963-078-SM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
34945EXT Distribution Board, For One 87204x/206x Or 87606B Switch And Two N181x Switches
Y1152A
Distribution Board
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
Product
Low PIM Cable Assemblies
-
Manufactured using industry standard low PIM cables terminated with RF Industries or other brands of connectors. Assembled in the United States for quick delivery. Jumpers are assembled from a wide variety of in-stock connectors and cables to meet system requirements for flexibility, low loss, low PIM, in-door/out-door, fire rating and electric performance.
-
Product
Taper System, CCD Beam Imaging Camera
TaperCamD series
-
355 to 1150 nm, standard CCD detectorHyperCal Dynamic Noise and Baseline Correction software (Pat. Pending)CTE Comet Tail Elimination for > 900 nm (Pat. Pending)Port-powered USB 2.0; flexible 3 m cable, no power brick14-bit ADC, 4 MB image buffer & on-board microprocessorWindow-free sensors standard for no fringing25,000:1 electronic auto-shutter, 40 s to 1000 ms1,000:1 SNR (30/60 dB Optical/Electrical)
-
Product
50 Ohm MMCX to MMCX Cable Assembly
40-977-571-0.5m
RF Cable Assembly
This 0.5m long MMCX cable assembly is part of the range of RF cables. Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
26-Pin MS-M RF Connector Housing, Female
40-969-526-F
-
These components allow users or their designated cable assembly suppliers to create their own cabling solutions for use with the Souriau MS-M RF connection solution.
-
Product
Connectors
-
We feature high performance coaxial connectors, including smp bullets. Also edge launch 2.92mm & 2.4mm connectors. & We've just started offering connectors that can be used to make cable assemblies. SMA Conectors are available for cables, and we also have sma connectors -thread in style.
-
Product
Cable Fault Meter
-
A cable fault meter can locate open power cables, either live or dead (without current), with voltages up to 300 V. A cable fault meter can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power from the cable which is being tested. Many cable fault meter devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
Product
PXI 2A Multiplexer, 2-Bank, 64-Channel 1-Pole
40-614-010
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends
A068SMR-T-5A100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
PXI SPST Power Relay: 20-ch, 5A, 300W
M9135A
SPST Switch
The M9135A is a general purpose switch with 20 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module is ideal for switching heavy loads or power supplies including voltages mains or DC current. The heavy-duty armature relays are rated for up to 5A and 300W, enough for inductive or capacitive loads. Choose from the heavy-duty power connector or an unterminated power cable.
-
Product
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" Depth
410112664
Enclosure
Enclosure, G18, Hinged Cover, 3 Cable Clamps, 7" DepthIncludes hinged cover, handles and 3 cable clamps- allow a max. cable bundle of 1.59 sq. inches per clamp. ITA strain relief plates. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Position Sensors
-
Position sensors are made of a specially-manufactured and calibrated measuring cable and a highly accurate graduated drum. They are very easy to install and are ready for use in a very short time.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 8 20-Pin Ribbon Cable Connectors
540160010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 8 20-Pin Ribbon Cable Connectors
-
Product
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth
410112712
Enclosure
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth Includes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With the cable clamps open- stiffener bar can be removed allowing installation or removal of cables without unplugging patchcords from the assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Enlarge Environmental Chamber
REXMED REC-450
-
MOD. REC-450, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,644 Watts, 12,433 BTU/hr, 3,140 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Cable, Power over Camera Link (PoCL), MDR to SDR, 5M
199745-05
-
26-Pin MDR/SDR Camera Cable - The PoCL Cable provides a Power over Camera Link (PoCL) cable assembly. This cable carries power as well as signal communication for PoCL applications between compatible cameras and frame grabbers. The PoCL Cable is available in 26-Pin Mini Delta Ribbon (MDR) male to 26-Pin MDR male, or 26-Pin MDR male to 26-Pin Shrunk Delta Ribbon (SDR) male variations.
-
Product
Pressure Based Waves
5218
-
Measure pressure based Waves with the Aanderaa Wave Sensors- compact fully integrated sensors for measuring wave and tide conditionsThe 5218 wave sensor is designed to be mounted on the Aanderaa SeaGuard top-end plate or connected to SmartGuard using AiCaP CANbus or in other measurement systems using the RS-232 interface.The 5218R wave sensor sensor is designed for use with long cables by means of RS-422 full duplex interface.Both wave sensors are based on a silicon piezoresistive pressure sensor. The pressure measurements are sampled and temperature compensated by an advanced Digital Signal Processor.The wave sensor application areas are in fixed installations, either deployed in a seabed installation in shallow waters, or mounted onto a fixed structure in the upper water column.
-
Product
USB Extension Cable
152166-02
USB Cable
USB Extension Cable - The USB Extension Cable is available in various lengths to help you extend the length of a USB Cable. This cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use the USB Extension … Cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
Product
USB Cable
143556-02
USB Cable
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 10A, 0.5m
A020GFR-F-0C050
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
