-
product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
product
Measuring Display Unit Breakers
Mitsubishi Electric Automation, Inc
Measuring display units (MDU) are integrated with molded-case circuit breakers and earth leakage circuit breakers for measuring, displaying, and transmitting information on cable ways. This display unit closely monitors energy consumption by measuring current, voltage, power, electric energy, harmonic current, leakage current and power factor.
-
product
Attenuation Control Unit, DC to 18 GHz, 0 to 121 dB, 1-dB Steps
J7201B
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 5716
The ProDAQ 5716 is a 1U high rack-mountable signal conditioning box for standard 19 in. racks. It provides signal conditioning for up to 16 strain gage or ICP sensors. Either one ProDAQ 3416 16-Channel ADC Function Card or up to two ProDAQ 3424 8-Channel 24-bit Sigma-Delta ADC Function Cards can be connected to the unit.
-
product
Pulsed Source Measure Unit
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
-
product
Data Acquisition Unit
The Teledyne Test Tools T3DAQ1-16 is a 16 channel Data Acquisition System incorporating the latest 4.3 inch (10.92 cm) dual-display technology which can be configured to show Data Histograms, Data fluctuation Trends, Bar Graph, Statistics or the traditional Number mode, all in an easy-to-use interface.
-
product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
2U, 4U, and 6U Developmental RF Interface Units
1257A-D
The Astronics 1257A-D is a sixth-generation RFIU design. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features, including the ability to acquire all of the components you need to assemble your own unit in-house, reducing your design time.
-
product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Analog Measurement Unit
AMU05
The AMU05 (Analog Measurement Unit 05) is the core of all our test systems. It ensures that all the measurements are performed faster, more accurately and with even greater stability.
-
product
6U VME COTS System, Sensor Interface Unit
SIU6
NAI's SIU6 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU6 leverages NAI field-proven, 6U VME boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
product
Programmable AC&DC Power Supply Unit
PADS
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
product
Measuring Complex for Registration of Test Parameters of a Pumping Unit
Portable portable complex for measuring and recording parameters of factory testing of horizontal pumping units.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)
CMCSK-03-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Power Distribution Unit with Switchable Outputs, Soft Start & Integrated Ethernet Switch
PDU-200
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
product
Electronic Control Unit Functional Test
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
product
LXI Matrix Switching Unit
ProDAQ 6140
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
product
Piezo Unit Aging Tester
BK2028/BK2028A
We designed the BK2028 and BK2028A Piezo Unit Aging Testers for you to test your piezo electric vibration units for long term reliability. The BK2028 can test up to 50 units at a time, while the smaller BK2028A tests 20. Both models are easy to set up and can be stacked. They allow you to control the number of tests you you run so that you can run a large number of DUT's under exact conditions and make sure your piezo units will do what you expect them to do for the life of your products.
-
product
PXI Source/Measure Unit
Keysight PXI source/measure unit (SMU) offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. It delivers industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading for faster test time.
-
product
Precision Source / Measure Unit (1 Ch, 100 FA)
B2901B
The Keysight B2901B precision source / measure unit (SMU) is a 1-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current. It easily measures current versus voltage (I/V) with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
product
Battery Extra Load Units
BXL Series
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
product
Front Panels for Plug-In-Units | IEC
Front panels for plug-in-units according to IEC | with or without EMC protection | aluminum 2.5 mm | clear anodised
-
product
dBAlert Personal Noise Warning Unit
GA907
dBAlert! activates only when the noise exceeds a pre-set level, warning exposed workers that noise levels have become dangerous and to put on their ear-defenders.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - United Kingdom 240VAC
781630-06
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Manual Drive Unit
ATE MA350
Parallel contact stroke: 20 mm. Contact force max.: 300 N. Component on PCB: 58 mm. Pressure frame unit-opening angle: 66.Weight: 2,60 kg
-
product
Vibration Control, Monitoring and Diagnostics System for Hydraulic Units
Stationary system for vibration control, monitoring and diagnostics of hydraulic units is used for constant technological and safety control, diagnostics of vibrational and mechanical parameters of hydraulic units and auxiliary equipment of hydroelectric power stations in accordance with the applicable requirements.
-
product
INERTIAL MEASUREMENT UNIT
MS-IMU3050
Extreme performance in the industry's most compact package, the ITAR free and EAR99 MS-IMU3050 represents the next generation of cutting edge MEMS IMUs. With an ultra-durable and dimensionally stable MIC-6 alloy housing, MIL-A-8625 coating, and Mil-Standard interface connector, the MS-IMU3050 will endure the most demanding environments, giving long term stability and reliability in your application.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMCSK-04-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Energy-Conservation Unit For Servopulser Hydraulic Power Supply Unit
ECU1/ECU2 Series
Up to 50 % energy savings. Contributes to reduced CO2 emissions and lower running costs. The conventional hydraulic power supply unit for fatigue and endurance tests is always driven at full power to achieve the maximum test force and maximum velocity and the hydraulic power supply unit is selected in order to satisfy the maximum test performance. Therefore, depending on the test conditions, energy is excessively consumed. With the ECU Series the motor rotational speed and the supply pressure of the hydraulic power supply unit can be set in multiple stages, so energy savings of up to about 50% can be achieved depending on the test conditions and test circumstances. It is used in combination with the Servo Controller 4830. (The Servo Controller 4830 is provided separately.) * Appearance and specifications are subject to change without notice.
