-
Product
Multi Output Buffer Unit
MS 1632
-
The Multi Output Buffer Unit is used for driving singe input to 32 outputs. This unit drives an analog input to two different 16 set of outputs through two 50 Pin standard D Type connector. The unit works on standard 230V AC.
-
Product
ESI(Electronics Systems Integration Unit)
MS 2004
-
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Data Acquisition Unit
-
The Teledyne Test Tools T3DAQ1-16 is a 16 channel Data Acquisition System incorporating the latest 4.3 inch (10.92 cm) dual-display technology which can be configured to show Data Histograms, Data fluctuation Trends, Bar Graph, Statistics or the traditional Number mode, all in an easy-to-use interface.
-
Product
Load Monitoring Units (LMUs)
-
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
Product
Programmable Logic Unit PLUS
V2495
-
The V2495 can be controlled and programmed “on the fly” via the VME Bus or directly through the Mini-USB connector on the front panel. A Software tool is provided for free to easily upload the custom Firmware on the User FPGA.
-
Product
Interface Units
-
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
Product
Control Units
-
For integration into a larger system or for automated measurements, the gain control unit for automated systems lets you control the settings of the intensifier attachment. The control unit uses standard TTL and analog signals for communication, allowing the user to switch the intensifier on or off, alter the gain and the anode current limit of the image intensifier without the need of software integration.
-
Product
16 Channel, Single Slot, Bench Data Acquisition Unit with 6.5 Digit DMM
T3DAQ1-16
-
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes. Includes Spring Tip, tip protector, and standard accessories package.
-
Product
Vibration Control, Monitoring and Diagnostics System for Hydraulic Units
-
Stationary system for vibration control, monitoring and diagnostics of hydraulic units is used for constant technological and safety control, diagnostics of vibrational and mechanical parameters of hydraulic units and auxiliary equipment of hydroelectric power stations in accordance with the applicable requirements.
-
Product
6U VME COTS System, Sensor Interface Unit
SIU6
Sensor Interface Unit
NAI's SIU6 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU6 leverages NAI field-proven, 6U VME boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
Product
Load Support Unit
LSU220A
-
The LSU220A is a general purpose load support unit designed to act as a permanent power supply to maintain backup battery systems whilst alternative sources of power are either impractical or unavailable, such as running diesel engines during maintenance programs.
-
Product
Pneumatic Units
-
Astronics PGA’s Pneumatic Unit enables you to provide a complete set of comforts in your upscale airplane seats. Adjustable firmness levels plus massage features ensure passengers feel pampered while enjoying the amenities of the flight.
-
Product
Data Acquisition Unit CATCH
MS 1523
-
CATCH is a web based locomotive monitoring system. This system provides locomotive data on Internet. Locomotive data are automatically download and organized at one place. The downloaded data can be viewed from anywhere through the Internet. By this flexibility the decision taking authority can get into an action immediately.
-
Product
Gateways & Remote Terminal Units (RTUs)
-
Linux-based Gateways and RTUs offer edge communication for remote maintenance, acquiring data and trasmitting to higher-level management systems.
-
Product
Tow Doctor™ Trailer Side Test Unit
50928
-
Hopkins Manufacturing Corporation
Specifically designed so that one person can make sure a trailer has been wired properly and all functions are working. Plug the Tow Doctor™ into the trailer connector and the power cord into a battery source and cycle through the trailer lighting functions. Includes 7 Blade, 6 Round and 4 Flat test connectors and durable carrying case.
-
Product
RFID Evaluation Units
-
- Wide range of interfaces for RFID evaluation units- Robust antennas and ID tags with long writing / reading distance
-
Product
Data Retrival and Analyzer Unit
MS 1200
-
*Retrieves the Data from Magnetic / Solid State Recorders (Supports JAGUAR, AN32, IJT, ALH Platforms)*RS232/RS422/Bi-Phase/USB interface with PC AT*Presents Error Messages and Test Reports*Replay, Analysis and printout of selected parameters*Calibration facility for ADR and DAU*Portable System for Snag Analysis of Aircraft*Reports in Tabular/Graphical formats*Used to check serviceability of ADR, DAU without removing from aircraft
-
Product
Phasor Measurement Unit Calibration System
6135A/PMUCAL
-
The 6135A/PMUCAL system is the only fully automated and traceable PMU calibration system available today. It fully complies to the IEEE C37.118.1™-2011 and section 7 of IEEE C37.242:2013 standards for PMU operation and verification.
-
Product
Emergency Power Supply Unit (EPSU) (8) 5-15R 1U/0U V/H
EPS-815-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Portable Strain Gage Welding and Soldering Unit
700
-
A battery-operated capacitive discharge spot welder for attaching and wiring weldable strain gages and temperature sensors.
-
Product
Dry Contact Control Unit
ZET 7161
-
The ZET 7161 is a three-channel control dry contact unit.
-
Product
Source / Measure Unit (SMU) Modules, N6700 Power System
System
The Keysight N6780 family of source/measure units (SMUs) provide advanced features and precise control and measurements of voltage and current down to the microampere and nanoampere regions. They provide stable, glitch-free output voltage and current during high-speed load changes, fast output modulation, and high-speed measurements of both voltage and current simultaneous.
-
Product
PXI Source Measure Unit
Source Measure Unit
PXI Source Measure Units (SMUs) combine high-precision source and measure capability with features designed to reduce test time and increase flexibility. These features include high channel density for building parallel SMU test systems, deterministic hardware sequencing for minimizing software overhead, and high-speed update and sample rates for quickly changing setpoints and acquiring data. Additionally, the flexible sampling rate and streaming capability of PXI SMUs allows you to use the instrument as a digitizer to capture transient behavior, and the digital control loop gives you the ability to adjust the transient response of the instrument. The ability to change the transient behavior of the SMU, called SourceAdapt, reduces SMU settling time and minimizes overshoot and oscillations, even with highly capacitive loads.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - United Kingdom 240VAC
781630-06
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Programmable AC&DC Power Supply Unit
PADS
-
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
Product
Battery Loading Unit
BLUe
-
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
-
Product
Tow Doctor™ Vehicle Side Test Unit
50918
-
Hopkins Manufacturing Corporation
Specifically designed so that one person can make sure a vehicle has been wired properly and all functions are working. Plug the Tow Doctor™ into the vehicle towing connector, carry the display unit to the cab of vehicle and cycle through the vehicle lighting functions. Includes 7 Blade, 6 Round and 4 Flat adapters and durable carrying case.
-
Product
Nose Wheel Steering Unit And Steering Collar
-
Nose Wheel Steering Unit and Steering Collar for the V-22 Osprey.
-
Product
Front Panels for Plug-In-Units | IEC
-
Front panels for plug-in-units according to IEC | with or without EMC protection | aluminum 2.5 mm | clear anodised
