Analog Output Modules
-
Product
Analog Output Device
Analog Output Module
The Analog Output Device helps you create applications such as stimulus-response, power supply control, deterministic control, and sensor/signal simulation. The Analog Output Device supports various output resolutions, channel counts, and other onboard features, so you can replace several kinds of instruments in your system, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.The Analog Output Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PCI-6704, 16‑Bit, 32‑Channel, Static Analog Output Device
777306-01
Analog Output Module
The PCI‑6704 is a static analog output device that you can use for software‑timed voltage and current output applications.
-
Product
8-CH 12-Bit Isolated Analog Output Cards
PCI-6308 Series
Analog Output Module
- Supports a 32-bit 5 V PCI bus- Isolated 8-CH 12-bit voltage output- 2500 VRMS optical isolation- Jumper selectable bipolar and unipolar output ranges- 4-CH isolated DI and 4-CH isolated DO- Current output version available on PCI-6308A
-
Product
12-Bit, 4-Ch Isolated Analog Output Universal PCI Card
PCI-1720U
Analog Output Card
4 12-bit D/A output channelsMultiple output ranges2,500 VDC isolation between the outputs and the PCI busKeeps the output settings and values after system resetOne DB37 connector for easy wiringUniversal PCI and BoardID™ switch
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCI-7256
Analog Output Module
- Supports a 32-bit 3.3 V or 5 V PCI bus- 16-CH latching SPDT relay outputs- Power saving on relay actuation- Output status unchanged when power-off- On-board LED indicators for relay status
-
Product
32-CH Discrete Output Modules with U Profile
HSL-DO32-UD
Digital Output Module
*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps
-
Product
NI-9485, 8-Channel, SSR Relay, 60 VDC/30 Vrms, 750 mA C Series Relay Output Module
779600-02
Relay Output Module
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
Product
8-CH 24-Bit High-Resolution Dynamic Signal Acquisition Module
PCIe-9529
Analog Input Module
The ADLINK PCIe/PXIe-9529 is a high-performance, high density, 8-CH analog input dynamic signal acquisition module. The PCIe/PXIe-9529 features eight 24-bit simultaneously sampling analog input channels. The 24-bit sigma-delta ADC provides a sampling rate of 192 kS/s at high resolution, making it ideal for higher dynamic range signal measurement. All channels are sampled simultaneously and accept input range up to ±10V, and the analog inputs support software-selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors. The module is especially designed to meet the requirements of vibration analysis and audio testing.
-
Product
96-CH 12-Bit 3 MS/s High-Density Analog Input PCI Express Card
DAQe-2208
Analog Input Module
ADLINK DAQe-2208 is an high-density and high-performance analog input card. The device can sample up to 96 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 48 AI channels in order to achieve maximum noise elimination.
-
Product
High-Density 128-CH Isolated DIO/DI/DO PCI Cards
PCI-7442/7443/7444
Analog Input Module
Responding to the industry"s need for high-density digital input/output modules, the ADLINK PCI-7442/7443/7444 DIO card series delivers up to 128 opto-isolated channels for a wide range of demanding PCI-based applications. The PCI-7442/7443/7444 series comes with 64 (PCI-7442) or 128 (PCI-7443) opto-isolated digital inputs and 64 (PCI-7442) or 128 (PCI-7444) opto-isolated digital outputs. With a 1250 VRMS (excluding cables) channel-to-system isolation protection, these cards are shielded from damage caused by accidental contact with external voltage while promoting simple ground connections. All input channels are identical non-polarity with each line isolated and suited to collect digital inputs even at high-noise environments. Featuring a Change-of-State (COS) interrupt function, the PCI-7442/PCI-7443 instantly generates an interrupt request to the PCI controller when it detects a sharp change in the logical state of any of its digital inputs.
-
Product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783362-01
Analog Input Module
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
Product
32-Ch Isolated Digital Output EtherCAT Remote I/O Module
AMAX-4834
Digital Output Module
Suitable for EtherCAT networks32-ch digital output with 2,500 VDC isolationWide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)Quick removable European type connectorLED indicators for I/O statusSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo Rotary switches for up to 256 slave IDs
-
Product
PXIe-4499, 204.8 kS/s, 114 dB, 4 Gains, AC/DC-Coupled, 16-Input PXI Sound and Vibration Module
781370-01
Analog Input Module
204.8 kS/s, 114 dB, 4 Gains, AC/DC-Coupled, 16-Input PXI Sound and Vibration Module - The PXIe‑4499 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4499 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4499 delivers simultaneous sample on all channels. In addition, the PXIe‑4499 includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gains, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
Product
32-CH Isolated DIO PCI Cards
PCI-7230/33/34
Analog Input Module
ADLINK"s PCI-723X series are 32-CH isolated input and/or output cards which provide a 2,500 V optical isolation protection. The wide input range of the PCI-7230 and PCI-7233 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The PCI-7230 and PCI-7234 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automation applications. The PCI-7234P provides current-source output capability. The PCI-7230 and PCI-7233 also provide two interrupt sources on digital input channels. The PCI-7233 also features a change-of-state (COS) function that generates an interrupt when any digital input changes its state.
-
Product
4-Ch Isolated Relay Output With IRIG-B Card
ECU-P1761
Relay Output Module
specialized interface module that combines four independent, electrically separated (isolated) relay contact outputs for switching external devices with a dedicated input/output port for receiving or transmitting IRIG-B serialized time codes.
-
Product
32-CH Sourcing Type Digital Ouput EtherCAT Module
EPS-2032
Digital Output Module
*32-CH sourcing type digital output*Quick removable European type connector*Slave module healthy monitoring*Wide operation temperature range*: -20°C - 60°CCompact size: 100 (L) x 100 (H) mm
-
Product
PXIe-4481, 24-Bit, 6-Channel, 1.25 MS/s/ch PXI Analog Input Module
784278-01
Analog Input Module
24-Bit, 6-Channel, 1.25 MS/s/ch PXI Analog Input Module—The PXIe‑4481 is an analog input module for higher bandwidth voltage measurements. The module offers analog and digital filtering for accurate frequency domain measurements. You also can select from four gain settings to configure your input range. For measuring sudden changes, such as high speed blast and pressure events, the PXIe-4481 can sample up to 20 MS/s per channel in time domain mode. The included NI-DAQmx driver simplifies hardware configuration and measurement.
-
Product
PXI 64-Channel Digital Output Module
40-412A-021
Digital Output Module
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
PXIe-4480, 1.25 MS/s, 3.4 Hz AC/DC-Coupled, 6-Input PXI Sound and Vibration Module
784277-01
Analog Input Module
1.25 MS/s, 3.4 Hz AC/DC-Coupled, 6-Input PXI Sound and Vibration Module—The PXIe‑4480 is designed for high-bandwidth audio, acoustic, and vibration measurements. It provides six channels of dynamic signal acquisition, and you can use one of four gain settings to configure your input range. The PXIe‑4480 also includes software-configurable AC/DC coupling, charge measurement, voltage excitation, IEPE excitation, and TEDS support, making it ideal for measuring acoustic transducers, pressure sensors, and hydrophones. Common applications include audio test; noise, vibration, and harshness (NVH) analysis; and underwater acoustic measurements. For measuring sudden changes, such as high speed blast and pressure events, the PXIe-4480 can sample up to 20 MS/s per channel in time-domain mode.
-
Product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
782999-01
Relay Output Module
The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
Product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Analog Input Module
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
Product
96-pin DIN Male to 96-pin DIN Female, 60 VC Shielded Analog Cable
157350-01
Analog Cable
SH-96-96-2, Cable for PXIE-4302, PXIE-4303, and PXIE-4339 to Rackmount Terminal Blocks, 1 Meter
-
Product
PXI Analog Input Module
Analog Input Module
PXI Analog Input Modules feature multiple analog-to-digital converters (ADCs) as well as built-in signal conditioning. Sample rates range from 5 kS/s/ch to 2 MS/s/ch. You can choose from modules that offer up to 28 bits of resolution and up to 32 simultaneous channels. PXI Analog Input Modules offer different types of isolation and filtering, so you can choose options that meet specific application needs. The modules promote increased accuracy, high data throughput, and are ideal for scalable measurement systems with low and high channel counts.
-
Product
PXIe-4163, 24-Channel, ±24 V, 50 mA PXI Source Measure Unit
784483-01
Analog Input Module
PXIe, 24-Channel, ±24 V, 50 mA PXI Source Measure Unit—The PXIe-4163 is a high-density source measure unit (SMU). It features 4-quadrant operation with a current resolution of 100 pA and the ability to sample up to 100 kS/s. The module also offers the ability to maximize stability and measurement accuracy with SourceAdapt, which allows you to custom-tune the transient response to match the characteristics of any load. The PXI-4163 is ideal for a broad range of mixed-signal integrated circuits (ICs) in semiconductor production test.
-
Product
PXIe-4357, 20-Channel, 24-Bit PXI Temperature Input Module
782118-01
Analog Input Module
20-Channel, 24-Bit PXI Temperature Input Module—The NI PXIe‑4357 input module provides integrated data acquisition and signal conditioning for 2‑, 3‑, or 4‑wire resistance temperature detector (RTD) measurements. It offers both high-speed and high-resolution modes. It provides per channel software-programmable configurations and automatically scale measured data into engineering units.
-
Product
32-CH Sinking Type Digital Ouput EtherCAT Module
EPS-2132
Digital Output Module
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
32-CH 12-Bit 100 kS/s Isolated Analog Input Card
PCI-9113A
Analog Input Module
ADLINK PCI-9113A is a 32-CH, 12-bit, 100 kS/s isolated analog input card. The PCI-9113A provides analog inputs with 3 programmable input ranges for both bipolar and unipolar inputs. The 32-CH single-ended analog inputs can be converted to 16-CH differential analog inputs, which improve the noise rejection in harsh industrial environments. The analog inputs are isolated from the PC's system ground. This feature not only protects the PC from being damaged from surges on the signal lines, but also eliminates ground loops and common-mode problems commonly seen in industrial measurement applications. The PCI-9113A provides custom circuit area for input signal conditioning. Either signal attenuation or filtering can be applied on per channel basis. With all the features, ADLINK PCI-9113A delivers cost-effective and reliable data acquisition capabilities for ATE, sensor monitoring, data logging, power transmission, and a broad variety of industrial measurement applications.
-
Product
96-CH High-Driving DIO Card
PCI-7396
Analog Input Module
The PCI-7396 is 96-bit parallel digital input/output (DIO) cards designed for industrial applications. The PCI-7396 emulates four 8255 Programmable Peripheral Interface (PPI) chips. Each PPI offers three 8-bit DIO ports which can be accessed simultaneously. The total 12/6 ports can be configured as input or output independently.
-
Product
Relay Output Board
VME-2232A
Relay Output Module
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
Product
PXIe-4464, 204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module
783087-02
Analog Input Module
204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and Vibration Module—The PXI‑4464 delivers simultaneous sampling on all channels. In addition, the PXI‑4464 includes built-in antialiasing filters that automatically adjust to your sampling rate, six software-selectable input gains ranges, and TEDS smart sensor support for error-free setup. The IEPE excitation circuit can deliver current for high-power sensors and strong data integrity over long sensor cable runs.
