PCB Adapters
-
Product
External DC Bias Adapter
16200B
-
The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.
-
Product
Coax, Contact, Receiver, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102135
Contact Adapter (Receiver)
Primary mating contact 610102134. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination 3.5mm compatibleInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.15 + .01 (f) GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mΩ max. center conductor3 mΩ max. shieldCable Specifications 3.5mm compatible Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MΩ min.
-
Product
PMC to PCI Adapters
-
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
Product
3-Pin Power D-Type Connector, 40A, Female PCB Mount
40-963-003-RF
D-Sub PCB-Mount Connector
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
Flexible x1 PCI Express to MiniPCI Express Adapter
SKU-056-02
-
The Flexible x1 PCI Express to MiniPCI Express Adapter (Adapter) was designed to convert the x1 PCI Express bus into the MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion add-in board to the motherboard PCI Express connector.The Adapter includes a MiniPCI Express adapter board (downstream), x1 PCI Express host board and PCI Express flat cable.
-
Product
Test Port Adapter Set, 2.4 Mm To 3.5 Mm
85130F
-
The Keysight 85130F test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector designed for connecting to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. The set contains a 2.4 mm to PSC-3.5 mm male adapter and a 2.4 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 26 dB or better.
-
Product
Adapter, 1.0 mm (f) to 2.4 mm (f), DC to 50 GHz
11922B
-
The Keysight 11922B precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
-
Product
50-Pin D-Conn Female Straight PCB
40-963-050-SF
D-Sub PCB-Mount Connector
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
ProLink to ProBus2 Adapter
LPA-PBUS2
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range-Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 155gf
K100-C150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
PC Based Test Setup for LED PCB of Luminaire
-
The panel carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 40 seconds.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
-
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Test Adapter / Extender
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
Product
Differential Pressure Adapter w/ App Compatibility
DPA1
-
UEi Test & Measurement Instruments
The DPA1 measures positive, negative and differential pressure and is compatible with iOS® and Android™ mobile devices. Measurement units can be selected from the following scales: InH2O, mmH2O, psi, bar, mBar, kPa, InHg and mmHg. The mobile device screen will display a numeric reading. And is backed by a 1-year warranty.
-
Product
FlexRIO Adapter Module Development Kit for Modular I/O
780711-01
Module
FlexRIO Adapter Module Development Kit for FlexRIO—The FlexRIO Adapter Module Development Kit (MDK) for Modular I/O enables you to choose the specific converters, buffers, connectors, and other components so that you can build the exact analog and digital I/O you need into a custom adapter module for FlexRIO. NI recommends that you have custom printed circuit board (PCB) design and hardware description language (HDL) code development experience to use the FlexRIO Adapter MDK for Modular I/O.
-
Product
Single Rear Slot Universal Low-Profile PCI to Compact Flash Adapter
P312
-
To cater for the latest generation of Low Profile PCs that can only use Low Profile PCI add-in boards, Elan has created the P312. This model, from the P-Series range, features a Compact Flash Type II ejector and a circuit board that conforms to the MD1 profile specification. It will allow you to use any Compact Flash card such as IBM MicroDrives, Bluetooth cards, WLAN 802.11b cards, data acquisition cards, pager cards, GPS cards etc.
-
Product
PMC-to-PCI Express Adapter
4749
-
Our PMC-to-PCI Express Adapter 1X (64-Bit) (4749) permits the use of a single-wide PMC module in a 1X PCIe slot. The product features a PEX8114 bridge running in transparent mode.
-
Product
NI-5732, 80 MS/s, 14-Bit, 2-Channel Digitizer Adapter Module for FlexRIO
781658-02
Digitizer
The NI‑5732 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 80 MS/s. You can use the NI‑5732 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5732 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Desktop PCB Test System
BOARDWALKER 9627
Test System
Qmax Test Technologies Pvt. Ltd.
QT9627 is a cost effective entry level model Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test .Maximum Digital Test Speed 10MHz in the QT9627 .
-
Product
MultifunctionAsync Serial Communications Adapter
2628
-
The Multifunction RS422/RS485/Digital I/O board provides a collection of various interfaces on a single-wide PMC module. The two 16550 UARTs on the board provide asynchronous communication at bit rates to 115Kbaud. The 16550?s are mapped into host processor space so that standard drivers can be used with the board.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 305gf
K100-L150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Osprey PCI Qbus Adapter
9668
-
Dual-height card plugs into PDP-11 Qbus backplane. Fibrechannel cable plugs into Qbus logic connector on Osprey /TXP. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
Product
Coaxial Waveguide Adapter, Type-N (f), 8.2 to 12.4 GHz
X281A
-
The Keysight X281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
-
Product
MPI PCB Probe Systems
-
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
-
Product
2.92mm Adapters
-
Pasternack 2.92mm adapter category is mostly RoHS and REACH compliant. 2.92mm adapter components are part of a complete adapter product line from Pasternack. 2.92mm adapters in straight or right angle versions are in stock and ready for shipment.Our 2.92mm adapter series allow you to interface 2.92mm connectors with 1.85mm, 2.4mm, 2.92mm, 3.5mm, 7mm, Mini SMP, N or SSMA connectors. 2.92mm adapters are available in female to female, female to male, female to sexless, male to female, male to male or male to sexless gender combinations. The 2.92mm adapter category includes bulkhead, 4 hole panel or mountless configurations.Our ISO 9001:2008 registered facility ships 2.92mm adapter parts the same day from the broadest and deepest in stock inventory of RF and microwave parts. Exceptional customer service and technical support are on hand to help you.
-
Product
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions
510109598
Strain Relief
Strain Relief Plate, Receiver/ITA, SIM, PCB or wired solutions.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
-
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Adapter, 1.0 mm (f) to 1.85 mm (m), DC to 67 GHz
11921H
-
The Keysight 11921H precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
Flexible MiniPCI to PCI Express Adapter
SKU-037-XX
-
The Flexible MiniPCI to PCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a PCI Express bus. It allows you to connect a x1 PCI Express add-in board to a motherboard that has a standard 124-pin MiniPCI connector.The adapter includes a MiniPCI host board, x1 PCIe (x4 PCIe is optional) adapter board and a PCI Express flat cable.
