PCB Adapters
-
Product
PCB TA01, 5 mV/g, IEPE, Accelerometer, Triaxial Vibration Sensor
780990-01
-
5 mV/g, IEPE, Accelerometer, Triaxial Vibration Sensor - The PCB TA01 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB TA01 features a sensitivity range of 5 mV/g.
-
Product
Supply Adapters
AP Series
-
*Overflow Relative Noise Temperature and Return Loss Measurement within all Frequency Range*Ultrawide Frequency Range*Small Size*4 Design Structures with Different Connector Types
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 305gf
K100-C150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Passive XMC-to-PCI Express Adapter
6067
-
The Technobox, Inc. P/N 6067 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 6067 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O. JTAG signals are brought out to headers allowing users the option of connecting the two JTAG ports.
-
Product
Reverse GPIB Cable Adapter
182768-01
GPIB Cable
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Male or Female GPIB (IEEE 488) Adapter - The GPIB Adapter connects GPIB cables to other accessories. NI offers it in Type XA, XE, and XF.
-
-
Product
DDR4 Pro 288-Pin DIMM Adapter
INN-8686-18-PRO
-
Your best option if you need to test a large volume of memory! The RAMCHECK LX DDR4 Pro 288-pin DIMM Adapter (p/n INN-8686-18-PRO) gives RAMCHECK LX users the power to test 288-pin DDR4 modules, including unbuffered (UDIMM), load-reduced (LR-DIMM) and registered modules (RDIMM), both ECC and non-ECC, that comply with JEDEC standards. It includes the DDR4 Series adapter and DDR4 Pro DIMM test head.
-
-
Product
NF-SF 50 N-Female to SMA-Female Adapter
-
NF-SF 50 Adapter, N-Female to SMA-Female, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
Product
PCB Handling
-
High performance handling solutions from 6TL, to achieve the best speed and performance for the test automation.
-
Product
Tap Adapter
-
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
Product
78-Pin D-Type Male Straight PCB Mount
40-963-078-SM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
VXI Plug & Play Adapter Plate, 8U, (also fits Racal 7U Chassis)
310113248
Adapter Plate
Used to mount 9025 VXI single tier receiver (Part # 310104127) to the VXI chassis. Flanges must be purchased from the manufacturer.
-
Product
4U Grille Adapter
AD-7
-
Used to install 19” panel width blowers, fan and grille/filter assemblies in 24” panel width enclosures.
-
Product
USB CAN Interface Adapter
COMMDongle
-
Designed for use with VISUALCONNX and other third-party software, COMMDongle products initially support one or more CAN communications buses.
-
Product
OEM 1-Channel Fiber Optic Signal Conditioner PCB Module
FOTEMP1-OEM-MNT
-
The FOTEMP1-OEM-MNT is a small form factor PCB interface module designed for low cost insertion of high precision GaAs-based fiber optic temperature sensor technology into OEM applications where common electrical temperature sensors and thermocouples cannot be used. The OEM interface product is compatible with all TS series fiber optic temperature probes. The sensors are entirely non-metallic and electrically passive, providing immunity to EMI, RFI, MR, microwaves and radiation is required.
-
Product
NI-5762, 250 MS/s, 16-Bit, 100 MHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
781749-01
Digitizer
The NI‑5762 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 250 MS/s with options for 100 MHz of analog bandwidth or an unfiltered path. You can use the NI‑5762 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
-
Product
Interface Adapter
DMX-10
-
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
Product
Adapter
ZET 430
-
*Aligns sensor output signal with the FFT spectrum analyzer input;*Sends the FFT spectrum analyzer generator signal to the sensor calibration input;*Provides power supply to the sensor from the integrated ±12 V power supply unit.
-
Product
37-Pin D-Type Female Straight PCB HV
40-963-037-SF-HV
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
CEI-2x10GBASE-T
Network Interface Controller
- Support up to two 10GbE BASE-T interfaces- Marvell AQR113C inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 305gf
K100-I126305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Adapter, 1.0 mm (m) to 1.85 mm (f), DC to 67 GHz
11921G
-
The Keysight 11921G precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
-
Product
78-Pin D-Type Male Right-Angle PCB
40-963-078-RM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
XMC-to-PCI Express Adapter
4823
-
The Technobox, Inc. P/N 4823 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 1x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
37-Pin D-Type Female Straight PCB Mount
40-963-037-SF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Banana-Triax Adapter For 4‑Wire (Kelvin) Connection
N1297B
-
The N1297 Series is a collection of banana-triax adapters for the Keysight B2900 Series precision source measure unit (SMU). It consists of both 2-wire as well as 4-wire connection requirements.
