-
product
Professional Cable Tester
1EA560
Multifuncional tester with LCD display enables to show wire maps and combination of pairs and their lenghts. It also measure the lenght until the broken line / cable. It is suitable for CAT5, CAT5E, and CAT6 cables. With special interface is also suitable for testing of coaxial and telephone cables. It has special unit for testing of cable ends in the other room.
-
product
Line / Hood Test Equipment
The units will test any length, class, or style of hose in today's market.
-
product
Primary Injection Test Equipment
High current injection units for primary testing of over current relays and circuit breakers.
-
product
High-Voltage Test Device
PGK 150 / 5 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK H. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 150 kV output voltage with positive or negative polarity* AC voltage testing - up to 110 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
product
SIMRC - RS232 to I2C Converter PCB
1080-001
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
product
AC Fuel Flow Signal Generator
TA-100
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
product
Specialty Test Systems
The innovative products of D&V Electronics lead to cutting edge advancements – applied technology that will drive future transportation. Our specialty testing products are the cumulative result of our technological advancements that drive innovation, further our industry and enhance the quality of our customers’ products. From compact electric motor testing units to full electrical testing systems, we have the solution to always be TESTING THE FUTURE®.
-
product
Unit Testing & Mocking Solution for .NET
Isolate
Part of Typemock Isolator,The Complete Unit Testing & Mocking Solution for .NET From mocking to coverage to automated test suggestions
-
product
Electricians' Accessories
A selection of voltage detectors, proving units, test leads, certificate books and a DVD, which make it that bit safer and easier to get the job done.
-
product
Compressed Air Testing
Parker's compressed air testing units provide a cost-effective means of quickly evaluating compressed air for the presence of microbes. The units are lightweight, ergonomically designed for ease of use, and supported by Parker's global sales and service network.
-
product
ABex Rear Module for Utility Power Supply
ABex RM-UTILITY
The ABex RM -Utility is a rear module for the ABex-System. It provides 5 galvanically isolated fixed supply voltages for TUA (Test Unit Adapter) and cabinet supply. It features an over current protection and a software-controlled power enable.
-
product
High Temperature Humidity Analyzer
CI-IN19
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
CI-IN19 humidity analyzer uses vast-contrast humidity sensor as testing unit. It’s an intelligent analyzer at the core of micro-processor and made of detector part & display part. It’s use to measure the relative humidity in air and vapor mixed gas between o to 200℃. - See more at: http://en.ci-ele.com/fb01357d-94e6-2795-f3d2-ea8d5b3a3d31/f7847efb-fece-c4be-5376-3bd0f9a8eeba.shtml#sthash.KCqpmhCp.dpuf
-
product
Coil Analyzers
SAT Series
The Coil Analyzers SAT30A and SAT40A are powerful, lightweight units ideal for testing of circuit breakers. Substation battery is not connected or available. The SAT series instruments are intended to supply circuit breaker coils and spring charging motors. They spring charging motors (SAT40A – AC and DC) as a part of commissioning and maintenance testing.
-
product
Proven Testing Solutions for Critical Software
V&V Services
*Unit and integration testing*System and acceptance testing*DO-178 process definition and optimization*Test automation*Timing analysis and optimization*On-target problem solving*Third-party software verification*Assurance services
-
product
Multiport JTAG Tester
XJQuad
XJQuad is a 4-port version of the XJLink2 USB-to-JTAG controller targeted at PCB manufacturers. It is supplied with XJRunner software for running XJDeveloper test systems. With a range of special features it is particularly suitable for concurrent/parallel testing on the production line. Each of the four ports has a high-speed interface which can be connected to up to four JTAG chains on each Unit Under Test (UUT).
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
Jandel Test Unit
HM21
The Jandel HM21 Test Unit has six constant current settings between 100nA and 10mA, and can be used to measure voltages from 0.01mV to 1250mV.
-
product
Testers for Aerospace and Railway
Testers for the realization of a network with base unit and distributed test point units (TPUs).
-
product
C and C++ Testing, Static Analysis, Code Review
C++test
Parasoft C++test is a complete C/C++ developer's quality suite for static code analysis, code review, automated unit and component testing, coverage analysis, and regression testing ? on the desktop under leading IDEs and in batch processes. Available for common enterprise and embedded environments.
-
product
Automated Regression Testing
VectorCAST/Manage
VectorCAST/Manage is an extension of the VectorCAST family of unit and integration testing tools, answering all problems associated with manual testing and providing confidence in final results.
-
product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Digital and Analog Test Sets
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
product
JTAG 3rd Party Controller Support
Corelis offers support for a variety of devices and instruments from third-parties in an effort to provide existing test platforms comprehensive JTAG test execution with Corelis ScanExpress software products. Supported instruments include National Instruments PXI-655x HSDIO and Teradyne Di-Series modules. Corelis also provides support for JTAG testing with FTDI FT2232 ICs embedded on a unit under test (UUT).
-
product
Parametric Test Fixture
U2941A
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
product
Quality Control
Sandwich Box
Housed in a ruggedized box, the VQC Sandwich Box is a field-proven acquisition unit for testing all aspects of vibrator performance, providing real time display of accelerometer and reference signals during the sweep.
-
product
Universal relay test set and commissioning tool
CMC 356
The CMC 356 is the universal solution for testing all generations and types of protection relays. Its powerful six current sources (three-phase mode: up to 64 A / 860 VA per channel) with a great dynamic range, make the unit capable of testing even high-burden electromechanical relays with very high power demands.
-
product
BIP Tester
BIP TESTER is a measuring device designed for users that already have a unit injector test bench, but their lack reliable BIP measurement.
-
product
SpaceWire Isolator
134
The SpaceWire Isolator is an isolation unit for ground test and integration applications, providing galvanic isolation for two SpaceWire links. Isolation is tested to 60 V with components rated to 100 V and 2500 V max transient voltage.
-
product
Fiber Optical Monitoring Alarm System
FOMA
FOMA (Fiber Optical Monitoring Alarm System) is integrated RTU (Remote Test Unit) 、Center Monitoring Server and its management software to achieve integrated operation、remote management、unattended monitor、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record.
-
product
XCITE 1100 Field Test Series
The Xcite 1100 Field Test Series uses the same Exciter Heads and Master Controller as the 1100 Laboratory Series but replaces the 5 GPM 3-Phase Hydraulic Power Supply with a field portable 1.2 GPM Single Phase Power Supply. While providing the same 3000 PSI pressure, the field test unit is switch selectable from 110 V (20 A) to 220 V (10 A) single phase power.
