Voltage Current Sources
See Also: Current Sources, Voltage Sources
-
Product
C Series Current Output Module
Input/Output Module
The C Series Current Output Module features up to eight channels of simultaneous analog output. You can choose between enclosed and non-enclosed modules. Additionally, the C Series Current Output Module has built-in open-loop detection. This detection generates an interrupt in software when an open loop is detected, zeros outputs to ensure safety, and avoids driving actuators at system power-on. The C Series Current Output Module requires an external power supply and includes a channel-to-earth ground double isolation barrier for safety and noise immunity.The C Series Current Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Single-point Current Meter
-
The SEAGUARD® is the core module used in small and medium sized underwater observatories. Whether used as a multipurpose instrument, or as a hub for strings in the water column, the SeaGuard manages connected sensors and the real-time communication of data and meta-data to shore. In autonomous configurations, long battery life is achieved with aggressive power routines keeping the full system at the lowest power levels possible.
-
Product
Precision Current Shunt
-
Has five precision selectable Ultra stable Current Shunts which ranges from 0.0001 to 1Ω. The Shunt T/C is less than 10ppm, and the internal current meter will measure from 1μA to 1000Amps.
-
Product
High AC Current Capacitors
-
HK Film Capacitors offer a selection of High AC Current Capacitors ( continuous duty) with Temperature up to +105C
-
Product
Laser Source
-
Is an Amplified Spontaneous Emission (ASE) based broadband light source, designed for general laboratory applications. It is a reliable and cost-effective unit that can be ordered with multi channel options. The LD operating temperature and drive current are precisely monitored by a micro-controller to ensure constant output power and emission wavelength stability. With compact size configuration, it’s also suitable for OEM integration, User can control the ASE source output power level by adjusting the drive current along with remote status monitoring, contact Optilab for more information.
-
Product
Bluetooth Recording Current Meter
RCM Blue
-
A self-recording dedicated current meter with Bluetooth for communications and data retrieval - now with the possibility to integrate a pressure sensor!The RCM Blue is a self-recording Current Meter which also measures water temperature in salt or fresh water, and a battery container with battery capacity up to 70Ah. .The Doppler Current Sensor is an upgraded version of the proven SeaGuard ZPulse sensor. The RCM Blue instrument configuration and data retrieval is done via Bluetooth which eliminates the need to open the pressure case for repeated deployments.RCM Blue has now been upgraded with the possibility to integrate a pressure sensor with a 0,01% accuracy. This simplifies your work significantly as you will know exactly where you are in the water column.
-
Product
Voltage Control Attenuator
-
Voltage variable attenuator offering infinite attenuation precision and broadband performance
-
Product
High Voltage Test Set
Hi-Pot Series
-
SCOPE introduces a high voltage test set, these high voltage testing sets comes with Power frequency AC high voltage /DC high Voltage test /AC-DC high Voltage test set for testing transformers, motors, insulators, cables etc. Further, these testing sets are capable of giving continuously variable HIGH VOLTAGE from zero to maximum rated output voltage. Wide range of up to 100 kV is available in user selectable combinations.
-
Product
0-600A Current Data Logger
VA601-A2
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Multi-function record meter is a new record meter designed for the actual demand of various industrial site, which integr.
-
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-800B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Light source
UVM-MP
-
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
Product
Voltage Indicators
-
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
Product
High Voltage Breakdown Tester
Model HV-55
-
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 5 Kilo Volt DC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Gradually.
-
Product
Tunable Deuterium and Tungsten-Halogen Light Sources
-
Deuterium and Tungsten-Halogen tunable light sources are convenient and affordable solutions for your laboratory experiments. Their optimized optical design, delivers efficient and power stabilized broadband optical power with variable aperture and selectable bandwidth with wavelength ranging from 180 nm up to 2 micron depending on your choice of the lamp.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Surge Voltage Generator
SSG 3000
-
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
Product
Battery Voltage Recorder
BVR Series
-
Battery voltage recorders from BVR series are designed to serve as a support tool for cell voltage measurement during battery capacity testing.During capacity testing, cell voltage, temperature, inter-cell connection voltage, and specific gravity should be measured in order to determine failling cells in the string that should be replaced.Furthermore, IEEE standards for stationary batteries applications stipulate periodical measurement of overall string voltage, as well as cell voltage and temperature.The BVR Series is the perfect tool for that purpose. All measurements are automatically saved in device’s internal memory. Additionally, DV-B Win software helps the user to download all measured results. Furthermore, the user can create test reports and export them to various formats.BVR series includes two models: BVR11 and BVR22. These are rechargeable handheld devices intended for performing monthly battery inspections and support tools during capacity testing. The list of the applications of these instruments includes:Efficient supplement to BLU series of battery load units during battery discharge testingMonthly inspections of large battery banksAmbient temperature measurementCurrent measurement using current clampsUSB and Bluetooth communication with PCSimultaneous string voltage and current measurement to analyze a discharge test processThe BVR22 model provides Bluetooth communication with an external density meter, for transferring electrolyte specific gravity and temperature readings.
-
Product
Impulse Current Measuring Shunts
ICMS
-
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
Product
High Voltage Relays
-
Sensata | GIGAVAC brings you decades of experience in DC and RF applications of high voltage relays. With a variety of voltages from 2- 100kV, we will spend the time to guide you through all of the possible selections and tradeoffs. You can then make an informed decision based on performance and price. Our online Application Notes available 24/365 help explain the finer points surrounding High Voltage Relays.
-
Product
Visible Laser Source
VLS35
-
The KD Optics VLS-35 is a pocket sized, visible source used for testing fibre optic cable installations. The unit is pocket sized with a long battery life from a PP3 battery, making it ideal for local fault finding and continuity checking of fibres.
-
Product
AC Voltage Tester
-
AllWin Instrument Science and Technology Co., Ltd.
1. AC voltage tester2. TFT LCD3. PLC,RS232C,RS485 interface4. MCU control technology
-
Product
JFET Voltage Preamplifier
SIM910
-
Stanford Research Systems, Inc.
The SIM910 and SIM911 are low-noise, programmable preamplifiers which are ideal for a wide range of small signal applications. The primary differences between the two models are their input impedance and input noise.
-
Product
Current Differential and Overcurrent Relay
SEL-387
-
Schweitzer Engineering Laboratories, Inc.
Protect and control any two-, three-, or four-winding power transformer with the SEL-387, which provides thermal and through-fault monitoring, and with SELogic Control Equations, can detect breaker failure.
-
Product
Monochromatic, Fiber-Coupled LED Light Sources
-
LED light sources in the LS-MC1 series provide a constantly growing selection – currently amounting to over 20 – of narrow band single wavelength LEDs with a bandwidth of 15-50 nm FWHM, allowing precise work in a defined wavelength range. As a result of optimized optical coupling into the optical fiber – as with all of our light sources – with our LS-MC1 series we have achieved the highest possible luminance. The advantage of directly emitting monochromatic LEDs is their very high level of efficiency, because the entire radiated output is in the useful wavelength range.
-
Product
Current Transformers
-
The Institute of Electrical and Electronic Engineers defines a current transformer (IEEE Std C57.13) as “a transformer intended to reproduce in its secondary circuit, in a definite and known proportion, the current of its primary circuit with the phase relations substantially preserved”. Its primary winding is connected in series with the conductor carrying the current to be measured or to be controlled and its secondary winding is connected to the measuring, protection or control devices. Osborne designs and manufactures current transformers which are used for instrumentation applications, others which are used for power system synchronizing applications and others which are used in protection circuit application. They have been designed to meet specified current ratios, burden impedance and transformation errors.
-
Product
Voltage Detectors
-
Non-contact voltage detectors can quickly detect live AC voltage. These handy devices are great for electricians to safety and quickly check the status of electrical wires.
-
Product
Source Code Review
-
If code is legacy and massy and application is not performing well enough ,want to optimize your application internal structure.
-
