Filter Results By:

Products

Applications

Manufacturers

Test Ranges

wide open to vast test areas.

See Also: Weapon, Antenna Test


Showing results: 2116 - 2130 of 2375 items found.

  • PCI Fault Insertion Switch Range for Differential Serial Interfaces

    50-200/201 - Pickering Interfaces Ltd.

    Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.

  • Battery Capacity Tester

    BLU-T Series - IBEKO Power AB

    Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conducted in an accurate, user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU-T battery load bank enables setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, the BLU-T units can be connected in parallel, or BXL-T additional load units can be linked.The instrument offers a high power-to-weight ratio. BLU-T series has models starting from 12,8 kg / 28.2 lbs and up to 19,2 kW of power.A user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Discharge parameters can be monitored in real-time during the capacity test. A 4,3-inch touch screen shows overall battery voltage, discharge current, discharge test time and capacity during the entire test. Also, the capacity tester is compatible with DV-B Win software. A user can view a detailed numerical and graphical presentation of key parameters, and create reports in various formats.Testing can be carried out without disconnecting the battery from the service.

  • Ground Grid Tester

    GGT Series - IBEKO Power AB

    The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.

  • Calibration

    Kiwa Dare

    Calibrations of electronic equipment is one of the activities that Kiwa Dare offers to its clients. these calibrations are under accreditation in the field of electrical quantities. Besides calibrations in the field of DC current, DC voltage and low frequency (test and measuring) equipment, Kiwa Dare is specialized in calibrating high frequency measuring equipment and in particular EMC equipment in a frequency range of (DC) 40 GHz. New the site validation calibrations whereby Kiwa Dare can calibrate shielded rooms (Faraday room) and anechoic chambers under accreditation.

  • QAM DVB Analyzer

    Wuhan Sunma Technology Co., Ltd.

    QAM Analyzer designed for both installation and maintenance of HFC system. Measure and display main parameters in DVB testing (channel power, MER, BER, Constellation Diagram), signal level on any frequency, amplitude of the carriers singly in the whole system range, and etc. The Analog, QAM and FM channel can be set and tested efficiently; it also supports HUM measurement, C/N measurement, voltmeter function, spectrum analysis and data logging. Also it is easy for user to obtain a report of test data via PC or printer through toolbox software.

  • Easy-to-assemble and Collapsible RF Test Enclosure With Fabric Shielding, ≥ 90 DB Isolation, 300 MHz - 18 GHz

    dbTENT - DVTest Inc.

    The dbTENT is an easy-to-assemble, store and transport high-performance RF test enclosure. Whether you need to make measurements in the field or in the lab, the dbTENT provides superior 90 dB of isolation over a wide frequency range thanks to its patented double layer conductive fabric design. Featuring an interchangeable customisable I/O panel, the dbTENT meets all your needs for non-permanent isolated testing. With a setup time of only minutes, the dbTENT will get you ready for testing instantly in a wide variety of environments.

  • Multifunction Electrical Installations Meter

    MPI-520 - Sonel S.A.

    The MPI-520 multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520 is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.Wide range of standard accessories enable to perform all necessary measurements and safety test. Highly professional portable multifunction meter with memory of measured parameters.

  • Performance Testing & Engineering Services

    ImpactQA

    At ImpactQA, Performance Testing & Engineering services are focused at providing end-to-end testing and reporting solutions to global clients. Our performance team makes use of a holistic approach to deliver quality software applications. We manage performance testing services for a broad range of applications such as web, mobile, client-server, and cloud systems. ImpactQA with its extensive performance test & engineering lab help clients launch trustworthy applications by conducting effective load testing supported by volume testing, stress testing, etc.

  • Industrial Electronics Testing for Smart Devices & More

    Circuit Check, Inc.

    As more and more devices are being designed with inherent intelligence and the ability to connect and communicate, the amount and complexity of electronic content is continuously increasing for our industrial customers. They need the ability to quickly and efficiently verify proper operation of these products as they flow off the production line. Circuit Check responds to these needs by offering a wide range of industrial electronics testing solutions from consulting to complete test system and software design. We also offer adaptable support solutions to ensure proper equipment operation throughout its life cycle.

  • 600A Digital Clamp Meter

    7128C - Peaceful Thriving Enterprise Co Ltd

    This is an auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC/DC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity, frequency and non contact voltage sensing. Sub switch included Function Select, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Hz/Duty Cycle, Illumination and Back-light.

  • Stability Chambers

    Tenney Environmental

    Lunaire Environmental is a leading manufacturer of steady state and shelf life testing chambers and walk-in rooms which provide constant climate testing and meet ICH guidelines. These steady state chambers and rooms are perfect for long-term material testing on packaged products in controlled temperature storage. Lunaire steady state climatic test chambers are also ideal for research facilities and laboratories because they simulate wide range of temperature, and temperature and humidity environments. Click here for an overview brochure on Tenney and Lunaire equipment offerings.

  • True Average Connected Power Sensors

    CPS2000 - Boonton Electronics

    CPS2000 True Average Connected Power Sensors provide USB, LAN and PoE capabilities to enable easy RF power measurement of modulated and CW signals from 50 MHZ to 8 GHz. Compatible with Windows and Linux systems, CPS2000 sensors include all the necessary drivers for programming through SCPI, IVI and LabVIEW. Connectivity and compatibility, combined with 60 dB dynamic range and 100 measurements per second, CPS2000 sensors are the ideal solution for lab, field, production test, ATE remote monitoring and embedded environments.

  • Spring Testers

    IMADA, Incorporated

    Imada offers manual or motorized spring testers in vertical or horizontal configurations.Lever-operated manual systems enable rapid compression and tension spring testing.Wheel-operated manual systems enable slower, more precise movement with the hand wheel.Motorized compression testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All spring testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.

  • System Amplifier

    SAM100 - Rohde & Schwarz GmbH & Co. KG

    The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals

  • Ruggedized PC104+ & PCIe/104 System

    Dragon - Excalibur Systems, Inc.

    Excalibur’s Dragon is an advanced, ruggedized PC104 and PC104+ system in an enclosed, modular casing. The system is appropriate for use in data acquisition, recording nd control for any combination of ARINC-429, MIL-STD-1553, Serial, Discrete or similar types of communication. The modular, stack through design of the PC104/PC104+ platform allows you to build a tailor-made configuration based on Excalibur’s extensive range of boards plus any 3rd party cards of the customer’s choosing. Our engineers will integrate and test all 3rd party cards to the customer’s specification.

Get Help