-
Product
Additional Products: 78 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
8-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - XMC
Model 71132
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Powerful Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight wideband DDCs (digital downconverters)- 64 multiband DDCs- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction cooled versions available
-
Product
E-Series Average Power Sensor
E9300B
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Signal Converters For Adapting Encoder Signals To The Interface
-
The signal converters from HEIDENHAIN improve compatibility with the subsequent electronics by adapting the encoder signals to the interface. Signals can be interpolated, and different designs can be selected for greater flexibility in the application.
-
Product
VTAC, Patchcord, Receiver , 18", VTAC to USB-C
7-142715757-018
VTAC Patchcord
VTAC, Patchcord, Receiver , 18", VTAC to USB-C This high speed VTAC patchcord is made in accordance with USB Type C specifications. Electrical performance conforms to USB 3.2 Gen 1 Data Rates, 5 Gbps. Full feature USB 3.2 Gen 1 compatible with C-C applications. Please note: Lengths for this patchcord and its mating patchcord cannot exceed 18" to ensure product performance is not impacted. Also sold as a kit with both ITA and receiver patchcords, p/n 740KIT001.
-
Product
PXI/cPCI Modular Embedded Controller - PXI 2.0/PCIe 3.0 Compatible, Max 512MB DRAM (256MB Installed)
TE9500-1200
-
TSI's modular approach to PXI embedded controllers provides maximum flexibility and upgradeability for most, if not all, PXI embedded controller requirements. The TE9500 series of embedded controllers is based on the industry standard ETX (embedded technology extended) SOM (system-on-module) form factor. Whether you choose a power saving Celeron CPU or a high performance mobile Pentium III, the TE9500ís integrated interfaces and upgradeable options apply across all models of the TE9500 series of controllers. The TE9500 series gives you the ability to control your controller.
-
Product
10A Continuity Tester
EQUITEST
-
EQUITEST is connected to its master unit via C2050 cable and to the mains for power supplying.Please refer to the user manual of your HT installation safety tester for the compatibility to EQUITEST.
-
Product
Conveyor Compatible & Conveyor Compatible
Automator Double Sided
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
SA1500X, 1.5 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784256-01
Oscilloscope Probe
The SA1500X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
Product
Micro Dsub GPIB Cable For PZ2100A (1m)
PX0114A
GPIB Cable
The cable converting MicroD25 GPIB to standard GPIB; compatible with the Keysight PZ2100A
-
Product
RFID Testing
-
Regulatory changes and demanding testing procedures put RF product manufacturers under pressure to adhere to updated market requirements. We help you navigate the complex process of complying with radio performance testing requirements to ensure your RFID products are compliant, compatible, and reliable.
-
Product
sbRIO-9881, Non-Enclosed, 1-Port C Series CANopen Interface Module
785966-01
Interface Module
The sbRIO‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. The sbRIO‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The sbRIO‑9881 is compatible with only CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
Enclosure, G20X, Hinged Cover, 8" Depth
410112984
Enclosure
Enclosure, G20X, Hinged Cover, 8" DepthNOTE: This enclosure is NOT compatible with the EMI ITA P/N 410120253.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
15.6" Ultra-Slim All-In-One POS System
USC-360D
-
15.6" Ultra-slim all-in-one POS system equipped with Rockchip RK3568 quad-core Cortex™-A55. Supports Android 12 or Linux operating systems, Compatible with a wide range of periphearls for retail and hospitality applications.
-
Product
cPCI Serial Power Supplies
-
CompactPCI Serial (PICMG CPCI.S-0) has added a number of features and benefits while maintaining backward compatibility to create a foundational spec for serial-based CompactPCI technologies. This includes an updated power supply specification. CompactPCI Serial requires only one +12 V power supply with a maximum power of 79.8 W per 3U module and 171 W per 6U module as well as a 5V stand-by voltage.
-
Product
DC-14GHz Divide-by-8 to 511 Programmable Integer Divider
UXN14M9P
-
The UXN14M9P is a highly programmable integer divider covering all integer divide ratios between 8 and 511. The device features single-ended or differential inputs and outputs. Parallel control inputs are CMOS and LVTTL compatible for ease of system integration. The UXN14M9P is packaged in a 40-pin 6x6mm leadless plastic surface mount package.
-
Product
PCI Daughter Boards
DB-16R
-
The DB-16R is a 16 channel Relay Output Board. It consists of 16 form c relays for efficient switching of load by programmed control. It is connector and functionally compatible with our 785 series boards with industrial type terminal blocks. The DB-16R can be used by our A-82x board or any other compatible board. The relays are energized by applying a 5 volt signal to the appropriate relay channel on the 20-pin flat cable connector. Sixteen enunciator LEDs, one for each relay, light up when their associated relay is activated . This board provides a screw terminial for power to avoid overloading your PC's power supply.
-
Product
22 Bit / 2 MS/s Arbitrary Waveform Generator
AWG22
Waveform Generator
A 22 bit Arbitrary Waveform Generator for medium-speed / high resolution waveform generation.The AWG22 is upwards compatible with the AWG20 and also features differential outputs with a programmable common-mode voltage.
-
Product
400-Watt DC/DC Converter
VPX55-3
DC Converter
NAI's VPX55-3 is 400-Watt DC/DC Converter that plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
4 Digit LCD Data Display
DDM 4
-
The DDM 4 is a low power 4 digit data display module with 12.5mm (0.5") digit height. Inputs are CMOS and TTL compatible. Using three inputs Clock, Data In and Load, it is possible to display 0 to 9 and A to F or any other combination of the segments. The display can be panel mounted using the bezel and window
-
Product
PCIe-8431, PCI Express, 2-Port, RS485/RS422 Serial Interface Device
782124-01
Serial Interface
The PCIe‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PS/2 Type; ATX 400W
PS400-XP2
-
*Input Range: 90 ~ 264VAC Full Range*Output Voltage:**+5V, 20A (0.5A min)**+3.3V, 20A (0.3A min)**+12V1, 16A (1A min)**+12V2, 16A (1A min)**-12V, 0.5A**+5Vsb, 2.5A (1A min)*MTBF(hours): At 25°C, 100,000h*Safety: TUV, CS22.2 NO.60950-1, IEC, UL, NEMKO+CB, CE*Dimensions: 150 x 140 x 74 mm*Compatible with Axiomtek products: AX61221/AX61222/AX60501/AX60551/AX60552/AX61400/AX6145/AX6156/AX61492/AX61220
-
Product
NI-9234, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module
779680-01
Sound and Vibration
4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The NI‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9234 is also compatible with smart TEDS sensors. The NI‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Laser Tracker SMRs & Laser Tracker Probes
-
MetrologyWorks provides a full line of Laser Tracker Spherically Mounted Retroreflector (SMR) Ball Probes. Every SMR is compatible with all OEM Laser Trackers including FARO, API, and Hexagon (Leica). We Currently offer 3 Laser Tracker SMR Versions in 3 Sizes.
-
Product
SHDB15M-15F
147791-05
-
The SHDB15M-15F is used to connect compatible NI Frame Grabber Devices to a camera. It is offered in 2 and 5 meter options.
-
Product
PCB Contacts
-
VPC contacts are available in a variety of configurations to support flexible PCB mounting including right angle, vertical, twin female & male, and adapter pins (rounded posts).Many PCB receiver contacts are compatible with standard ITA contactsFor questions regarding compatibility, contact a Field Application Engineer.
-
Product
Portable Test Platform
FTB-4 Pro
-
The FTB-4 Pro is the latest addition to EXFO’s test orchestration portfolio which transforms business as usual into smarter, scalable network testing that significantly increases operational efficiency and provides vital insights into field operations, network performance and service delivery. The 4 slot modular FTB-4 Pro platform enables a unique combination for 100G commissioning, turn-up and troubleshooting which includes the FTBx-88200NGE 100G Multiservice tester (with iOptics transceiver validation software) and the FTB-5240S-P optical spectrum analyzer. There is no need to carry additional platforms or swap modules for unmatched transport and spectral testing on a single platform that no one in the industry can offer. The versatile FTB-4 Pro platform supports a wide range of modules for field testing, data center interconnect, submarine testing, and lab applications for maximum flexibility and ROI across all phases of the service delivery chain: development, deployment, maintenance and troubleshooting. Module combinations on the FTB-4 Pro can also include iOLM/OTDRs, market leading OLTS for fiber characterization, dispersion solutions and other transport modules all with compatibility with EXFO’s market leading fiber inspection probes.
-
Product
16-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - 6U VPX
Model 58131
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports two Xilinx Kintex UltraScale FPGAs- Sixteen 250 MHz 16-bit A/Ds- Sixteen multiband DDCs (digital downconverters)10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB105
-
The FAB105 features a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB105 is perfect fit for AXIOMTEK's SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB105 is compatible with the AX60501 chassis.
