PXI Serial Interfaces
See Also: Serial Interfaces
-
product
Serial Converters/Isolators/Repeaters
ULI-200
To keep your serial equipment communicating and smoothly integrated with new technologies, B B SmartWorx powered by Advantech has developed the most extensive line of serial conversion and isolation products on the market.
-
product
Fifo Serial Analyzer
FSA32
FSA32 is a Windows based protocol analyzer for debugging serial asynchronous communication. FSA32 uses the standard COM ports of a PC and does not require any other hardware except for the physical connection to the line.
-
product
Digital and Serial I/O
At Abaco, we're committed to the future of your VME systems, and we provide you with the flexibility and functional density you need.
-
product
Digital and Serial I/O
VadaTech’s wide range of ATCA Rear Transition Modules (RTMs) and MicroTCA I/O AMCs make it easier to integrate these standards-based building block systems into your network or application.
-
product
PXI-8512, 1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-01
1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
16-Port Serial Controller
PMC523
The PMC523 provides a flexible solution for technology insertion by integrating multiple serial I/O channels onto a single board computer (SBC) with a PCI Mezzanine Card (PMC) site. This gives customers affordable protection from obsolescence and a smart evolutionary path to enhanced software ultimately improves performance and increases efficiency.
-
product
10RJ50-DB9M Serial Cable, 10Pos Modular Plug to DB-9, 1 m (non isolated)
182845-01
S8 Serial Cable, 10Pos Modular Plug to DB-9, 1 m (non isolated)
-
product
Interfaces
Used for the collection of signals from many types of transducers and laboratory instruments. They connect to Windows and Macintosh computers via USB, and are supplied with Chart and Scope software for real-time display and analysis of the recorded signals. In addition, the EChem software module offers both traditional and advanced techniques for electrochemists.
-
product
Serial Port Splitter
With COM Port Splitter you can split one real port into several virtual ports, join real ports into one virtual, and redirect the serial traffic from real port to another real or virtual. You can also share one real serial port among several applications so that they will receive the same data from one serial port simultaneously. You can also join several ports under one name and let applications switch among the free ones. COM Port Splitter is very good at splitting any hardware COM port into multiple virtual COM ports, so that each of them behaves exactly like the original port and has the same name. All virtual ports receive any data that is received by the original port at the same time. For example, COM Port Splitter can let a single serial device interact with multiple applications at the same time. Another job COM Port Splitter can do for you is join some real COM ports into one virtual port, which is rather useful when you need some application to handle multiple serial devices simultaneously. All data received by one of the joined COM ports is instantly forwarded to the joining virtual port and to the application, and vice versa. It is also possible to redirect all serial traffic from a hardware COM port to another COM port (hardware or virtual) with COM Port Splitter, meaning that any data sent to the redirected port is immediately received on the port you redirected it to. You may need this in case you are using some software with very strict serial-port settings and instead of figuring out how to modify those settings you can just redirect the data traffic to it. Besides, COM Port Splitter is essential for creating complex bundles of real and virtual serial ports and interconnecting them as you wish, therefore enabling data exchange between those ports.
-
product
Serial I/O Expansion
PCM-G-COM8
The PCM-G-COM8 is an 8-channel PC/104-compatible serial module. It is well suited for embedded applications requiring a large number of serial I/O ports. Each channel supports RS-232, RS-485, and RS-422 electrical levels to interface to a wide variety of serial communications devices such as modems, data collection equipment, and distributed I/O terminals. The PCM-COM8 will operate over the full industrial temperature range of -40° to +85° Celsius.
-
product
RS422/RS485 Serial Boards
104-COM-8S
These are eight, four, or two-port, asynchronous, serial communication boards designed for use on the PC/104 bus. They support RS-485 and RS-422 communications. The boards may be installed in any standard PC/104 stack. Connections are made via a 50 pin IDC type right angle connector.Common applications include POS, gaming systems, machine monitoring, military and high-density networking.
-
product
ECU Interfaces
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
product
Avionics PXI Express (PXIe) Interface Card - Multi-Channel, Multi-Protocol, 1553, ARINC, WMUX Interface for PCIe
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
product
4-Port Serial Interface
APCI-7500-3
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
product
Serial Parallel Interface
Model 2313
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
product
SATA (Serial ATA)
Serial ATA (SATA) is a data transfer technology designed to move data to and from storage devices such as disk drives, ATAPI drives, host bus adapters (HBA), and port multipliers. SATA is a serialized enhancement and replacement to parallel IDE. Since SATA ratification in 2003 and its move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with its industry leading protocol analysis and traffic generation capabilities.
-
product
Smart GPIB Serial Interface Board
Model 4816
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
Digital/Pattern/PE Card
PA64S
The PA64S represents a new level of performance and capabilities for PXI-based digital instrumentation. The PA64S offers high performance pin electronics and 16 sites of TMU/SPI/I2C/CLK generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be integrated, supporting up to 256 sites (16 boards).
-
product
Serial Converter
USB-COMi
The USB-COMi is a USB to RS485 serial converter. It allows easy serial port expansion without requiring IRQ, DMA, or I/O port resources. The converter allows the user to easily and economically connect RS485 devices to a host using USB. The RS485 communications standard is used by DGH sensor based data acquisition modules and many industrial control devices.
-
product
Serial I/O Boards
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
product
Interface Unit
CMM Automation
The Aberlink automation interface adds the capability for Aberlink 3D programs to be remotely controlled and monitored using an external system allowing any Aberlink CMM to be integrated with an automated component handling system, whether this be a fully controlled, PLC driven manufacturing system, a robotic loader or just an automatic bar feeder. The package comprises of an optically isolated digital I/O system and a software module that enables the software to be setup to follow a defined operating sequence to allow the automated operation.
-
-
product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
product
Quad Serial FPDP Interface with Virtex-6 FPGA - XMC
Model 71611
- Complete Serial FPDP solution- Fully compliant with VITA 17.1 specification- Up to 2 GB of DDR3 SDRAM- PCI Express interface up to x8- LVDS connections to the Virtex-6 FPGA for custom I/O
-
product
Interface
Renesas offers industry-leading devices to enable efficient and reliable communication for industrial control, networking and computing applications. Dual protocol transceivers, voltage level translators, I2C Buffers, wide operating voltage range RS-232 transceivers, and RS-485/422 devices with the highest noise immunity and ESD protection in small packages are available to support high-speed data transfer and a variety of configurations to fit your applications.
-
product
Serial analyzer
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
product
Interface Converters
Electro Standards Laboratories
Supporting a variety of medias, applications, and entities such as Casino/Lottery VLT Networks, Industrial Process Control, Government Laboratories, etc.
-
product
PXIe Remote Control Interface Module
43-921-003
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
product
Wireless Serial Device Server
SD-330AC
The SD-330AC serial device server is an ideal choice for connecting your serial devices for industrial automation, building automation and medical devices to a wireless LAN. It supports both Infrastructure Mode or Ad-Hoc Mode, which allows SD-330AC to connect to Wi-Fi networks at offices and factories to allow users to move, or roam, between several access points.
