Rf Power Amplifiers
See Also: RF Power, RF Amplifiers, RF Power Meters, RF Power Sensors
-
-
product
RF Power Amplifiers
RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99
-
product
RF POWER AMPLIFIERS
BSA Series
RF Input: N-f, standard on rear panelRF Output: standard on rear panel<1 kW N-f<3 kW 7-16-f<5 kW EIA 1 5/8Mains Supply: Line Power:<1000 VA 100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA 200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA 3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter: via status displayAmbient Temperature: 0 ... +45 °CStorage Temperature: -20 ... +85 °CRelative Humidity: up to 95% (non-condensing)Operating Altitude: up to 2000 m above sea levelVibration and Shock: MIL-STD-810 GCooling: forced air with integral blowerair intake from front, air exhaust at rear
-
product
RF Medium / High Power Amplifier
Corech Microwave’s RF medium/high Power Amplifier(PA) frequency ranges from 0.1 to 52 GHz, up to 100W high power output (CW or Pulse). Narrow-band & wide-band ready modules are available SMA, 2.92mm, 2.4mm, WR28, WR24 and PIN connector options are available.
-
product
Power Amplifiers
Triad’s line of RF and microwave Power Amplifier modules for extended range amplified radio applications set the bar for efficiency, linearity, and size-to-power ratio. We have designed hundreds of COTS modules for exacting frequencies up to 40 GHz . They offer high power levels into the hundreds of watts. And if a standard RF/microwave amplifier design does not fit your exact requirements, we’re specialists in creating custom-modified versions of any of our COTS power amplifier modules.
-
product
RF POWER AMPLIFIERS
BLWA Series
A) RF-Sample Ports I) 3x 208 V AC / 60 HzB) External Dual Directional Coupler L) LAN Remote ControlC) IEEE-488.2 GPIB Remote Control S) Internal RF Switching UnitD) Front Panel RF Connectors R) RS-232C Remote ControlE) RF Power Indication (digital) U) USB Remote ControlF) Gain Adjustment W) Liquid CoolingH) DC Supply X) External Control of other Amplifiers
-
product
RF Power Amplifiers < MMICS
Macom Technology Solutions Holdings Inc.
MACOM is continually enhancing and expanding its MMIC power amplifier product portfolio to meet customers’ demanding technical challenges by leveraging state-of-the-art foundry technologies and proprietary in-house processes. MACOM partners with today’s leaders in Test and Measurement, SATCOM, Aerospace and Defense, Public Safety Radios, Wired Broadband, and Industrial Scientific and Medical applications to deliver industry leading, high-performance MMIC solutions in bare die and high performance packaging.
-
product
RF Power Amplifiers
Specially selected products to complement our ultrasound measurement equipment.
-
product
Handheld RF Power Meter
V3500A
The V3500A Handheld RF Power Meter is a compact, handheld instrument that makes accurate RF power measurements in both field and manufacturing applications. With an absolute accuracy as good as 0.21dB, a wide frequency range of 10MHz to 6GHz, and a measurement range of -63dBm to +20dBm, the V3500A is suitable for a wide variety of RF measurement applications. Its built-in power sensor eliminates the need for users to carry both an instrument and a separate sensor module. Truly portable, the V3500A fits easily into your hand or a toolkit. An optional belt loop holster or carrying case with shoulder strap is also available. To optimize flexibility, it is capable of drawing operating power from batteries, an AC-DC converter module, or a computer via USB interface.
-
product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5021
The HMMC-5021 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5021 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gain response and excellent port matches over the 2-22 GHz frequency range.
-
product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Synchro Power Amplifiers
SSP
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
-
product
PXI Signal Amplifier
3180
Model 3180 was designed as a general purpose, wide band and high voltage amplifier, however, with specific applications in mind. It offers selectable gain of up to x50, with amplitudes of -90V to +90V and an output current of 150mA.
-
product
Signal Amplifier
9200A
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
30 VA Synchro Booster Amplifier
44PA1
The 44PA1 is a military grade Synchro Booster Amplifier that delivers 30 VA over the frequency range of 47 Hz to 10 kHz and will drive most CTs or TRs. It is transformer isolated, short circuit protected, and provides an accuracy of up to ±3 arc minutes.
-
product
Isolated Amplifier - 2 Channel, 50 Vpp
33502A
The Keysight 33502A is a dual-channel, high voltage output amplifier. It has an isolated analog front end with up to 50 Vpp (25 V) output voltage range. It is also a very low-distortion amplifier with < 0.01% @ 10 kHz and 40 Vpp. The 33502A is designed to work as a companion for function generators to offer low-distortion, higher voltage outputs.
-
product
PXI-2596, 26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module
778572-96
26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module—The PXI‑2596 is an RF signal multiplexer switch with dual 6x1 multiplexer banks in the same module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use the PXI‑2596 onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
PCI Bus Signal Amplifier
3322
Model 3322 is a 3U single-slot, PCI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3322 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
LXI Dual Bank, 12:1 MUX 75 Ohm 1GHz F-type
60-722-002
Our 60-722 High Isolation RF Multiplexer is suitable for switching 75 ohm signals up to 1GHz. With the choice of single or dual multiplexer banks each with 12 channels, it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted F-type connectors.
-
product
Terminal Board for Mitsubishi MR-J3-A Servo Amplifiers
DIN-814M-J3A0
This well-designed motion control terminal board is for the users who use Mitsubishi J3A servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Laser Sources and Amplifiers
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
-
product
Synchro Power Amplifiers
SPA
Computer Conversions Corporation
The SPA Series "Pulsating" Synchro Power Amplifiers are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and radar/Antenna related, applications. They are commonly used on synchro based data transmission, re-transmission, simulation and instantaneous absolute position indicating and active control systems.
-
product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PXI Voltage Amplifier, +/-33V
41-650-001-S1
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Synchro Power Amplifiers
SPB
Computer Conversions Corporation
SPB Series: 25VA, 30VA and 100VA Reference Powered Wide-Band 60/400Hz. Models
-
product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
