-
product
Amp Clamp
PPDCM80
The Power Probe Digital Clamp Meter is an 80amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter’s diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.
-
product
Cable Diagnostic Tools
For non-destructive diagnostic testing to determine the quality of a cable’s insulation with minimal risk of failure, HVI recommends tan delta and partial discharge testing for valuable diagnostic data about cable insulation integrity. Both use a VLF source to perform elevated voltage, off-line testing. Tan delta testing measures insulation health, while PD identifies specific problem areas and assesses their severity.
-
product
E84 Recorder
GCI's industry leading E84 Recorder is used by FABs and OEMs worldwide to locate and resolve E84 handshake issues due to signal drops and external interference. It non-intrusively captures the states of all E84 signals during live material handoffs and records them to the connected PC's hard drive. Short- and long-term recording modes are available using E84 Analysis, GCI's industry leading diagnostic software.
-
product
Cable Test and Diagnostics
Cable testing and diagnostics provides information about the cable’s global condition (e.g. the cable’s overall insulation system), and will reveal localised problems, such as poor joints and terminations; it will also reveal localised weak spots in the insulation. Various cable tests are carried out to spot potential failures before they can cause severe outages. Megger cable test equipment provides access to all of the technology needed to make informed cable management decisions through the different stages of the cable’s life cycle.
-
product
CMOS USB3 Cameras
CELERA One Series
CELERA One camera series provide the same excellence in quality, flexibility and performances of CELERA cameras, with the only exception of a single USB3 interface, while keeping the original extremely reduced dimensions and rugged design that make CELERA One cameras suitable for most applications: automated optical inspection, high performance sorting systems, industrial metrology, microscopy, medical diagnostics and machine vision.
-
product
Single-Axle Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/1 CAR | VP 230035
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/1 single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/1 CAR guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.
-
product
High-Voltage Test Device
PGK 110 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testin...show more -
product
Spray Fluxer Pattern Uniformity
Fluxometer
Improve Process Quality - Eliminate guesswork when it comes to managing the consistency of flux application during wave soldering. Ordered in the same width as your WaveRIDER pallet, the Fluxometer rides the finger conveyor through the fluxing stage, conveniently and accurately rendering proof of a tuned spray fluxer. So easy to use, operators can perform diagnostic checks in minutes.
-
product
Robotic Probing of Circuit Cards
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
product
Digital Tach/Advance Timing Light
125
*Professional Timing Light with High Visibility LED display Very bright display indicates: - Tach (RPM) - Degrees Advance *Measures ignition spark advance from 0-90 degrees *2 & 4 Stroke Tachometer measures engine speed up to 9,999 RPM *Brilliant Xenon flash at all speeds *Detachable & replaceable cable set *Designed for precise tuning and diagnostic work *Accurate up to 9,000 RPM *Works with 12 Volt electrical systems
-
product
LASAR Post Processor, Run Time And Diagnostic Test Solution
DtifEasy Series
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
product
Analysis Tool for ECU Networks and Distributed Systems
CANape
The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware,...show more -
product
Vehicle Standard Interface
VSI-2534
Vehicle reprogramming tools are becoming an essential auto diagnostic tool in automotive repair shops. Technicians often come across OEM Technical Service Bulletins that require them to reprogram the vehicle with the latest OEM calibration files in order to diagnose and repair car problems such as check engine light, gas mileage, false DTCS, shifting, hesitation, rough idle, emissions quality, ABS, performance, and more.
-
product
Digital "A" Flow Controller for High Flow
HFM-D-306A / HFC-D-308A
Mass flow techniques provide reliable, repeatable and accurate gas flow rate measurements.HFM-D-306A/HFC-D-308A mass flow instruments have flow ranges from 0-2500 slm to 0-10000 slm; provide analog and digital outputs, and are constructed of stainless steel. Easy, user friendly digital communications with windows based software interface available. Available with a variety of elastomer seals for maximum flexibility.Self diagnostics of the sensor, valve and overflow are included in the digita...show more -
product
Cable Diagnosis System
Baseline 9400 TDR/ICE
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
product
Oscilloscope Tester
ScopeTester 5
ScopeTester 5 is 5-channel oscilloscope tester for PCs. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
product
GL Products Online & Interactive Demos
*NetSurveyorWeb™ is a centralized VoIP network monitoring system. A number of GL's PacketScan™ probes and/or,PacketProbes™ are deployed in remote locations across the network to passively monitor VoIP traffic. Whenever a monitored call completes, the scan/probe calculates a variety of quality metrics (MOS, loss, delay, jitter, etc) and sends the metrics to the central Oracle database for storage.**The PacketScan™ is a feature-robust Windows® based software tool that captures and monitors live IP...show more -
product
Warm-Up Board
WECO 9000
The WECO 9000 Warm-Up Board from Radian Research provides a safe, easy to use, affordable solution to your AMI meter functional testing. The WECO 9000 originated as part of RADIAN Innovate™ Custom Design Solutions. Numerous process improvement workshops RADIAN facilitated at electric utilities have shown us that meter shops are experiencing as low as 65% pass yield on AMI meter testing. This means almost half the meters arriving are transported through the testing process and not ready for accuracy testing. Typical failures include inoperable display, diagnostic errors, disconnect switch in an open state, wrong firmware version, and inability to register on the communications network.
-
product
Heavy-Duty Diagnostics.
JPRO
JPRO Commercial Vehicle Diagnostics (CVD) scans any class 7-8 truck in less than a minute and displays 44,000+ detailed fault codes. With JPRO, technicians see and solve all issues related to the multiple systems found on the truck that may be causing problems with other vehicle components. Techs love JPRO because it saves them time, increases their efficiency during diagnosis and repair!
-
product
Laser Induced Fluorescence (Mixing LIF)
Planar laser-induced fluorescence (PLIF) is an optical diagnostic technique widely used in fluid and gas applications. PLIF has proven to be a valuable tool for flow visualization as well as for quantitative whole-field measurements of scalars such as concentration and temperature in liquid and concentration in gaseous flows. Applications can be found in process engineering, biomedical engineering, and fluid dynamics research.
-
product
DDLS 500 with 100 Mbit/s Real-Time Transmission
Leuze electronic GmbH + Co. KG
The DDLS 500 is a data transmission photoelectric sensor that, in addition to a high transmission rate of 100 Mbit/s, sets new standards – above all with respect to usability. An integrated alignment laser enables fast and precise mounting. Via the integrated web server, device diagnostics can be called up from any location.
-
product
EZ-Tach Digital Automotive Tachometer
325
The EZ-Tach makes RPM measurements quick and easy. This is a very useful tool for tune-up and other diagnostic work where accurate RPM readings are required. Just clamp over any spark plug wire and get accurate RPM on conventional or DIS ignition systems. The unit also features a data hold function. The large 2000 count LCD display shows; RPM, function, data hold indication and low battery indication. The EZ-Tach is powered by one 9 volt battery. Battery and instructions are included.
-
product
Serial Link Analyzer
HOTLink
The HSLA is a low-cost data recorder and diagnostics tool for 8B/10B encoded HOTLink systems. Each HSLA is preconfigured for a specific link speed (between 160Mbps to 1.0625 Gbps), and a connector type - copper (BNC, FCN, or SMA) or optical. The HL2View software makes data capture and analysis quick and easy.
-
product
Digital "A" Flow Controller for Low Flow
HFM-D-300A / HFC-D-302A
HFM-D-300A / HFC-D-302A mass flow instruments have flow ranges from 0-5 sccm to 0-25 slm; use all metal seals, provide analog and digital outputs, and are constructed of stainless steel. Easy, user friendly digital communications with windows based software interface available.Self diagnostics of the sensor, valve and overflow are included in the digital features. Also of interest is the auto zero feature which detects when the valve is closed and automatically resets the zero. These mass flow meters and controllers can store up to 10 calibrations of different ranges and gases. Another feature is the built in totalizer for monitoring gas usage under user set conditions.
-
product
TPMS Diagnostic Tools
An advanced diagnostic tablet compatible with U.S., Asian and European vehicles, 1996 and newer. This wireless Android-based touchscreen tablet performs comprehensive TPMS servicing including 1-Sensor programming to its extensive vehicle diagnostics capability including an all systems scan with ADAS identification, the ability to read/erase codes, view freeze frame and live data, bi-directional control including active testing, coding and adaptations.
-
product
Gas Chromatograph for Analyzing
GC2010D
Chongqing Kailian Yongrun Industrial Co.,Ltd.
Transformer uses oil as coolant and insulator. Gases are formed within the transformer oil due to natural aging, faults from oxidation, vaporization, oil breakdown, electrolytic action or insulation decomposition. Because the transformer oil bathes each internal component, dissolved gases in the transformer oil contain lots of diagnostic information. Meanwhile, the transformer is very expensive to be replaced, so monitoring these gases is very important to know the current quality of transformer or even when the transformer should be removed from service before failure. Presence of each gas composition and its concentration indicates possible failure of transformer.
-
product
Channel Analyzer
WifiMETRIX
WifiMETRIX is a new diagnostic tool used to analyze and test Wi-Fi networks. It is a handheld device that operates in stand-alone mode -- that is, it does not associate or connect with an AP. WifiMETRIX implements two important features -- AirHORN and WifiPROBE. The built-in Wi-Fi chip can perform both signal generation / packet injection (AirHORN) and throughput diagnostics (WifiPROBE) on each channel.
-
product
Process Control Instruments
burster präzisionsmeßtechnik gmbh
Measuring accuracy of up to 0.05 %, sampling rate 10 kHz maximal, innovative evaluation elements, i.e. windows, thresholds, trapeziums, envelope curves, freely definable mathematical operations, two synchronous processes can be monitored, 128 measuring programms, intelligent Signal sampling, programmable I/O functions, Ethernet, USB, RS232, extensive diagnostics and statistical analysis, all usual sensor interfaces, variable fieldbus interfaces, powerful PC Software
-
product
SS-OCT Lasers And Systems
Impressive performance, demonstrated reliability, competitive price, and superior customer service has made Axsun the market-leading brand among SS-OCT system developers, manufacturers, researchers, and entrepreneurs. The Axsun tunable laser platform is the core of thousands of state-of-the-art SS-OCT systems deployed worldwide in applications ranging from medical diagnostics to industrial inspection. Axsun SS-OCT Imaging Engines with integrated Data Acquisition enable compact high-performance SS-OCT systems with quick time-to-market, customizability and scanner compatibility, along with opportunity to scale rapidly.
-
product
Access Network Diagnostics
As fiber networks are built and services scale, Fiber Diagnostics helps Service Providers manage their customers’ experiences by ensuring successful installation and service start up, while decreasing time to revenue. Once the fiber network is in service, Enghouse Fiber Diagnostics assures customer satisfaction through improved customer service and rapid time to repair, while reducing operational costs.
