Diagnostics
Test routines run to determine errors.
-
Product
Automatic Engine Balancing Technology
AutoBalance™ System
-
Continuously adjusts fuel flow to each power cylinder to maintain balanced operationMinimize emissions and fuel consumption over a wide range of operating loadsReduce mechanical wear and maintenance costsReduce personnel costs and risk by eliminating manual engine balancingSupports engines with up to 20 power cylindersOn-Guard Diagnostic software for monitoring, analysis, reporting and trendingSupports automated air manifold pressure control for minimum emissions at varying loads
-
Product
Tan Delta Test System
-
Diagnostic test that indicates the degree of cable insulation degradation. Rather than using only a VLF instrument to perform a go/no-go proof test, the Tan Delta, used in conjunction with a VLF hipot, permits the user to grade the deterioration level of many cables in order to prioritize replacement, rejuvenation, or to determine what additional tests may be useful.
-
Product
Oscilloscope Tester
ScopeTester 5
-
ScopeTester 5 is 5-channel oscilloscope tester for PCs. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
Product
ISDD Tool Suite
-
The Integrated System Diagnostic Design or ISDD Tool Suite provides a start to finish solution for meeting all the diagnostic needs of system design. The ISDD design process is centered around functional modeling of systems which is used to develop the diagnostics and failure analysis necessary to fully support good system design. This includes: *Analysis of Fault Detection and Fault Isolation.*Analysis of critical failures and their impact upon safety.*Detecting and reducing false alarms caused by diagnostics.*The impact of prognostics upon fault detection/fault isolation and mitigation of critical failures.*Development of vehicle health management and troubleshooting diagnostics
-
Product
Signal Analysis
Synchronous Accumulation (Order Analysis)
-
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
Product
Advanced Diagnostics
-
Providing wireless vehicle communications between the vehicle and tablet and supporting the latest DoIP, D-PDU and Mega CAN vehicle communication protocols.
-
Product
16 DI/O IP67 Machine Mount M12 PROFINET/Modbus IoT Ethernet Remote I/O
ADAM-250PN
-
16-ch configurable DIO and 2-port power/ethernet daisy chainIEC 61131-2 type 3 sink DI and fast response source DOSupport I/O and power diagnostic and DO safety value protection functionsPrintable marking label & LED indicator monitoring system/network/diagnostic/power statusEnables cabinet-free front and side wall & machine mountingCompatible with M12 Screw lock and Push-pull fast-lockingRugged IP67 design resists EMC, vibration, dust, oil, and humidity from harsh/outdoorBuilt in Sensor/Actuator/Encoder Power Supply from each I/O portSupports PROFINET and Modbus/TCP, with extensible design for MQTT integration
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24 V.
APCI-1500
-
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
Product
Hydraulic Data Logger
HPM7000
-
The HPM7000 series, is a highly versatile portable hydraulic data logger and the evolution of the HPM6000. It is ideal for diagnostic testing of hydraulic systems, use on hydraulic test benches, pre-dispatch inspection or for Research and Development (R&D). There are a variety of different data logging modes with the ability to data log up to 16 million measured values per test at a variable interval from 1 ms, with a total possible storage size of 12GB (approx. 250 measurements).
-
Product
Optical Communication Probes
-
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
Product
Traffic Control Cabinets
-
Our intelligent traffic control cabinet designs are based on the most popular features of Safetran’s Caltrans, NEMA, and ITS cabinets. The ATCC uses high-speed serial communications, providing modern features, advanced diagnostics, enhanced safety, simplified traffic control cabinet wiring, and reduced traffic control cabinet size. The ATCC Standard supports both 120 VAC and 48-volt DC signal heads, while high-density load switches and quad detector modules allow for up to 32 signal outputs and 120 detection inputs.
-
Product
Precision Microcontrollers
-
Analog Devices provides a range of analog microcontrollers featuring ARM® Cortex™-M3 processors that help enable this product portfolio’s high precision, high performance, and low cost. By featuring ARM Cortex-M3 processors, our devices include a rich support system to aid product development throughout applications that include optical networking, industrial control, point-of-care diagnostics, and a variety of other industrial, instrumentation, and medical uses. Precision analog blocks including, but not limited to ADCs, DACs and references allow for precision control and measurements. Included also is the ability to read back diagnostics, which is a key requirement in the above applications.
-
Product
TPMS Tool
TPA 300
-
The Bosch TPA 300 is a comprehensive TPMS tool designed for sensor programming, activation and ECU reset. The full-color, intuitive interface guides the user when replacing and servicing TPMS sensors. When paired with a compatible Bosch diagnostic scan tool, like ADS 325 or 625, users can reset the ECU in less than two minutes. The TPA 300 supports all known OE and aftermarket programmable sensors for all light vehicles. Frequent updates allow new features, vehicles and sensor coverage to be added regularly.
-
Product
Intelligent Power Monitor
iPM
-
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
Product
Ultra-Low Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300U
-
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300U comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Microbiology & Diagnostics
-
The number and diversity of microorganisms infecting humans and animals are ever increasing. Understanding how microbes cause disease and evade treatment is crucial for the protection of global public health. Bruker supports researchers and healthcare providers in the rapid identification and analysis of microorganisms.
-
Product
Gas Filter Correlation Carbon Dioxide Analyzer
Model T360
-
The Model T360 CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Digital Multimeters
-
A digital multimeter (DMM) is a test tool used to measure two or more electrical valuesprincipally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries.
-
Product
Primary Test Manager
-
The Primary Test Manager™ (PTM) software supports you during diagnostic testing, condition assessment and data management of medium- and high-voltage assets, such as circuit breakers, rotating machines, grounding systems, instrument and power transformers as well as bushings and on-load tap changers (OLTC).
-
Product
High-Voltage Test Device
PGK 70 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
EV Diagnostics
-
A high voltage battery charger and discharger. Improve battery pack capacity with constant current charge, and discharge modes.
-
Product
APU Test Set
H296G Series
-
The H296G Series is a flight line diagnostic tool thatmonitors selected parameters and provides enginecontrol during APU trimming.
-
Product
Capacitance & Tan-Delta Test System
TD-1
-
By measuring the electrical properties such as capacitance and Tan-Delta regularly on periodical basis, it is possible to ensure the operational unexpected breakdown. Dissipation factor (Tan Delta) is one of the most powerful off-line nondestructive diagnostic tool to monitor the condition of solid insulation of various high voltage equipment.
-
Product
Access Network Diagnostics
-
As fiber networks are built and services scale, Fiber Diagnostics helps Service Providers manage their customers’ experiences by ensuring successful installation and service start up, while decreasing time to revenue. Once the fiber network is in service, Enghouse Fiber Diagnostics assures customer satisfaction through improved customer service and rapid time to repair, while reducing operational costs.
-
Product
Fast Ethernet SFP Module
SFP-FMM-2K
-
Hardened SFP/155-ED, MM1310/LC 2km (also known as 808-38102) Industrial standard small form-factor pluggable (SFP) package. Provides digital diagnostics monitoring (DDM) functionality, Wide specifications and fiber types available.
-
Product
Clinical Microplate Instrumentation
-
Clinical microplate instrumentation provides high efficiency and performance for your clinical diagnostic workflows. From ELISA microplate readers and washers, to multifunctional liquid handling, multimode detection and automated microscopy, Agilent BioTek microplate instruments and software are designed for ease of use in setup and operation, while providing powerful analysis for quick, high-quality results. For even greater automation and higher throughput, microplate stackers, handlers and automated incubators transform a benchtop instrument into a walk away automated system.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 3.5 W250 | VP 210153
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans.
-
Product
Maintenance Tools
-
The Carat Tools EMS provides technicians complete, intuitive control over the entire actuation system. This new software suite is available for either tablets or standard laptops, and can be used on the seat manufacturing assembly line or in the cabin for diagnostics and maintenance.
-
Product
Diagnostic Cores
Diagnostic VersaCore™
-
The diagnostic cores are uniquely designed in the VC20™ with Advanced Cantilever™ technology format. Using the customizable PCB, components can be added to create a “golden core” to quickly troubleshoot your system*Test SMUs*Test Motherboard*Test Pogo pins*Test Relay matrix
-
Product
ISA POST Code Display
post2b
-
Post2b = ISA POST code display, not RoHS compliant (can be considered test equipment, not subject to RoHS). Spec? During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h. Use post2b to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size?
