Diagnostics
Test routines run to determine errors.
-
Product
Software
TDAS Control
-
Diversified Technical Systems, Inc.
TDAS Control is the original set-up, control, viewing and export software developed by DTS. TDAS Control provides easy-to-use tools for configuring output timing, as well as advanced features such as automatic sensor assignment, detailed channel diagnostics, real-time display and squib fire for airbag testing. TDAS Control only works with TDAS G5 and TDAS PRO.
-
Product
SWaP Optimized Processing and Multifunction I/O & Communications System
NIU3A
Multifunction I/O
The NIU3A is a small, rugged, low-power, self-contained processing and multifunction I/O system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions. The NIU3A can also be configured with up to three smart Configurable Open Systems Architecture™ (COSA®) function modules. The NIU3A boasts Dual or Quad Core ARM Cortex®-A53 processors for customer software applications and I/O and communications management. The NIU3A is configured with two 10/100/1000BASE-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3A delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Intelligent Power Monitor
iPM
Power Monitor
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
Product
Ultra-Low Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300U
-
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300U comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Autocorrelator
PulseScout2
-
PulseScout2™ Optical Autocorrelators are a versatile, easy-to-use diagnostic tool for measuring ultrafast pulses from both high repetition rate (MHz) oscillators and low repetition rate (kHz) amplifiers from Visible to IR wavelength range.
-
Product
VLF/DC Hipot Cable Testing
-
From the outset, HV Diagnostics has been a pioneer in the development of a small, portable, single piece oil free VLF (Very Low Frequency) Hipot cable test instrument that would be reliable, user friendly and more technically advanced than anything available in the industry.
-
Product
Voltage Calibrators
-
Practical Instrument Electronics, Inc.
PIE has a voltage calibrator to fit your needs from the PIE 235 voltage and pH simulator to the advanced troubleshooting capabilities of the PIE 532 milliamp and voltage calibrator. The PIE 532 includes our patented Loop Diagnostic Technology! All the voltage/milliamp calibrators have fuse-less protection, rugged design and long battery life. With the PIE 535, source 4 to 20 milliamps or 10 to 50 milliamps into loop instruments and drive final control elements such as valves and actuators with up to 42 volts.
-
Product
Motor&Phase Rotation Indicator
-
Precision Mastech Enterprises Co.
A diagnostic tool used to identify the sequence or \(A,B,C\)) of a 3-phase power supply and determine the proper direction of rotation for 3-phase motors.
-
Product
E1 Testers
-
GAOTek provides a large collection of high quality, affordable E1 testers that are specially manufactured to speed up the ethernet maintenance time and work efficiency for sale to the United States, Canada and Globally. These devices consist of PING, router trace, a port location tool, a loop-back tool and offers a variety of Ethernet diagnostic functions. These E1 Ethernet test instruments are all incorporated with test tools for E1, V port, and Gigabit Ethernet link repairs, and failure diagnosis. E1 Ethernet testing devices are user-friendly, can be used in Ethernet cable tests, flux error code tests, connectivity performance, traffic testing, ethernet wire testing, and bandwidth verification. As these devices help in measuring and proving performance for criteria Ethernet networks they are commonly used in the RFC2544 performance test.
-
-
Product
Resistivity Meter for Concrete
Ohmcorr Test System™
-
OhmCorr has two probes spaced 1.97" (5cm) apart which are placed in holes drilled to a depth of 3/8th" (8mm) and filled with conductive gel. The direct digital read-out of resistivity is displayed on the LCD when the control switch is activated. OhmCorr and CorMap, when used together, provide an economical and sound diagnostic system of corrosion in reinforced concrete.
-
Product
Photomedicine Light Meters
-
Light meters for the measurement of optical radiation in therapeutic, diagnostic, ophthalmological, and endoscopic applications.
-
Product
Diagnostic Laboratory Software And Data Analysis
-
Enhance the way you manage quality control data, build connectivity in diagnostic workflows, ensure system security, and more with our diagnostic laboratory software and data analysis tools.
-
Product
Internal Resistance Testers
-
The Battery Internal Resistance Tester is essential for assessing the health and performance of stationary reserve power batteries. Designed for efficiency, this tester measures internal resistance, helping to identify potential issues before they impact battery performance. By providing accurate diagnostics, it enables proactive maintenance, ensuring reliability in critical applications. This advanced testing equipment is an invaluable tool for enhancing battery longevity and optimizing energy storage systems.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
Acoustic Emission Transducer
GT205
-
Acoustic emission transducer is a key element of non-destructive acoustic emission testing. Transducers GT 301 are used for technical diagnostics by means of passive ultrasound.
-
Product
Magnetic Rotary 3 Click
-
Magnetic Rotary 3 Click is a compact add-on board for accurate magnet-position sensing. This board features the AS5147, an SPI-configurable high-resolution rotary position sensor for fast absolute angle measurement over a full 360-degree range from ams AG. The AS5147 position sensor suppresses the influence of any homogenous external stray magnetic field, equipped with a revolutionary integrated dynamic angle error compensation (DAEC™) with almost zero latency. It also comes with onboard headers reserved for incremental and commutation signals of their respective A/B/I and U/V/W signals alongside embedded self-diagnostics, including magnetic field strength too high, magnetic field strength too low or lost magnet, and other related diagnostic features. This Click board™ has been designed to support BLDC motor commutation for the most challenging automotive applications.
-
Product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1-228X-S (Small IF) / 230514
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
E84 Recorder
-
GCI's industry leading E84 Recorder is used by FABs and OEMs worldwide to locate and resolve E84 handshake issues due to signal drops and external interference. It non-intrusively captures the states of all E84 signals during live material handoffs and records them to the connected PC's hard drive. Short- and long-term recording modes are available using E84 Analysis, GCI's industry leading diagnostic software.
-
Product
Diagnostic Cores
Diagnostic VersaCore™
-
The diagnostic cores are uniquely designed in the VC20™ with Advanced Cantilever™ technology format. Using the customizable PCB, components can be added to create a “golden core” to quickly troubleshoot your system*Test SMUs*Test Motherboard*Test Pogo pins*Test Relay matrix
-
Product
Clinical Diagnostics
-
Precise and easy-to-use discrete analyzers offer high-efficiency automated clinical chemistry, toxicology, and immunoturbidimetric assays. A wide selection of analyzers is available with throughputs up to 600 tests per hour to increase capacity and efficiency in any laboratory. Over 100 assays are available, including blood chemistry, electrolytes, infectious diseases, toxicology, and hormones.
-
Product
Medical Monitors
-
Advantech develops three types of medical monitors (PAX Series), including surgical, diagnostic, and clinical monitors.
-
Product
Integrated Vehicle Health & Monitoring
-
Military vehicles must have the ability to meet evolving combat requirements while operating under hostile conditions and the reliability to function effectively under such conditions. Integrated Vehicle Health Monitoring (IVHM) systems combine a range of diagnostic tools within a single platform and provide around-the-clock, intelligent diagnostics on critical mission, air, land and sea applications.
-
Product
Ignition Driver Units
-
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
Product
Digital Pressure Gauges
SCJR1-KIT-EMA
-
Parker's ServiceJunior diagnostic test kits are ideal to digitally measure pressure and capture min and max fluctuations in any hydraulic or pneumatic system.
-
Product
Machine Capability
NC-Checker
-
Metrology Software Products Ltd
We fine-tune your machine tools with automated diagnostics and precise calibration. We leave you with our NC-Checker software so you can benchmark the accuracy of your machine to assess its ongoing capability.
-
Product
Cable Test Vans and Systems
-
Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.
-
Product
Automation Monitor
-
The Automation Monitor is a diagnostic system for remote analysis and troubleshooting of semiconductor capital equipment. The monitor is capable of delivering synchronous streams from strategically located video cameras, sound devices and data sources on the equipment.
-
Product
Professional Thermal Camera
FLIR T540
-
Diagnose potential faults in industrial, electrical, and mechanical systems, or discover temperature anomalies in R&D testing with the 464 × 348 resolution FLIR T540. This portable, ergonomic thermal camera offers advanced features like 1-Touch Level/Span and continuous laser-assisted autofocus, making it the perfect non-contact diagnostic tool for condition monitoring and research applications. Streamline electrical/mechanical surveys, troubleshooting, and repairs with Inspection Route mode, which runs pre-planned routes created in FLIR Thermal Studio Pro (Route Creator plugin required) so users can record temperature data and imagery in a logical sequence. The built-in Macro Mode allows R&D users to quickly switch from wide angle to close-up analysis without changing the lens. When coupled with Research Studio software, the T540 helps engineers assess unexpected hot spots and find potential design flaws. The T540 also features FLIR Ignite for automatic uploading of images directly from the camera to the cloud for easy, secure storage and sharing. The purchase of a T540 camera includes a 3-month subscription to FLIR Thermal Studio Pro and FLIR Route Creator.
-
Product
On-Site Oil Analyzer
MiniLab 23
-
With two simple tests, the MiniLab 23 delivers on-site oil analysis, providing immediate actionable results, saving time and reducing costs. Highlights of this system include:*One product, delivering lab-quality analysis outside of the lab*Simplified workflow for the non-expert user, no chemist required *Simplified operation, data reporting and report interpretation via the TruVu 360 Diagnostic Sets with recommended actions.
