-
Product
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules
610131108
Pneumatic Contact (Receiver)
Mini Pneumatic, Contact, Receiver, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coaxial/ Mini Power modules.
-
Product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
-
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
Product
Pressure Balanced, Oil-Filled Hose
PBOF
-
Pressure Balanced, Oil-Filled (PBOF) hose assemblies from Teledyne ODI are designed and qualified to accepted industry standards. The double-walled hose design incorporates inner and outer elastomeric barriers with fiber reinforcements to withstand the demands of long performance life requirements in deep ocean interconnect and distribution applications. The hose is filled with non-conductive silicone oil, which acts as a pressure compensator and dielectric. The electrical and/or optical conductors are loosely housed within the oil-filled assembly.
-
Product
Pneumatic Contact, ITA, Hose Barb, for 1/8" [3.2 mm] ID Tubing
610131106
Pneumatic Contact (ITA)
Primary mating contact 610131107.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Extension Hose for Diesel Compression Testing
34729
-
Makes for easier diesel compression testing in areas with restricted clearance. Attaches between Cat. No. 34700, Diesel Compression Tester and Tool Aid brand diesel test adapters.
-
Product
Fuel Hose Assembly Tester - USAF
9201
-
The purpose of this equipment is to provide a source of high pressure fluid for proof testing of fuel hoses after assembly or on a periodic schedule as required by specification.
-
Product
Pneumatic Contact, ITA, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610132104
Pneumatic Contact (ITA)
Primary mating contact 610131104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Pitot Static Tester
ADSE 746
-
The ADSE 746 caters fully for all aircraft types and the different electrical power supplies. It can be used for testing high performance civil and military aircraft, fixed and rotary wing. Themulti-pressure outlets option can suit themore complex pilot-staticsystems.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The test set is robust and housed in a mobile weatherproof case fitted with tire wheels. An attached bag contains the pressure hoses and electrical cables.
-
Product
Abrasion Testers
-
Abrasion tester is used to determines the resistance of elastomers by the frictional loss of the rubber in products, such as tires, conveyor belts, hoses, footwear, floor covering etc.
-
Product
Pneumatic Comparator
-
Huaxin Instrument (Beijing) Co., Ltd
The vacuum pressure comparator is fitted with a differential pressure port that enables connection of gauges under test by hose.
-
Product
DIESEL COMPRESSION ADAPTER FOR FORD AND INTERNATIONAL
DTC1524
-
*M14 x 1.25 thread adapter attached to hose and a quick disconnect*Screws into the head of the engine in the glow plug hole*Use on International VT 365 engine used in the International 4200 medium-duty truck and Ford Powerstroke 6.0L used in the Ford F250-F550 trucks
-
Product
DURAMAX FUEL SYSTEM TESTER
DFST10
-
*Test diesel fuel pressure and vacuum on GM 6.6 liter Duramax engines*Includes 6' hose and quick coupler
-
Product
Radiator Flow Test Machine
8601
-
The Radiator Flow Test Machine P/N 8601 meets all requirements of military specification MIL-F-45955A (AL). It is completely self contained and requires only connection to a source of shop electrical power to place in operation. A power cable complete with three prong grounding plug is permanently attached to the machine for this purpose. The unit consists of a water storage tank, a pumping system, a flow measuring system, a support and workstation, and the required hose adapters for connection to different size radiators. The complete unit is mounted on swiveling casters. The flow rate is infinitely adjustable from 0 to 120 gallons per minute by means of a panel mounted control valve. The machine is constructed from heavy 10 gauge steel, is double welded and is coated externally and internally with a water-resistant epoxy coating. Flow measurement is accomplished by a digital panel meter with a calibrated accuracy of plus or minus 3 percent of scale between 5 and 120 gallons per minute. Higher flows available on request.
-
Product
Ralston Quick-test™ Connection System
-
Save time and frustration with Quick-test, the versatile system of quick connect high-pressure hoses and universal hose connectors that connect to anything.
-
Product
Bench Top Ionizers
-
Point-Of-Use Ionizer, Adjustable (30-100 PSI) Compressed Air IonizerNeutralize Electrostatic Attraction (ESA) to control contamination by dislodging dust and debris attracted by static electricity.Detachable 7'' long ESD Protective Flexible Hose with Thumb Button Designed to for a wide range of motion and simple operation.Adjustable Balance (20 Volts) with Less Than 1 Second Discharge Time At 6 InchMeets required limits ANSI/ESD S20.20 tested per ANSI/ESDSTM3.1 and ESD TR53
-
Product
Temperature Forcing System
ETF-SERIES
-
Precise Temperature Accuracies with Reliable Test Results Temperature Limits: -40/-60 °C to 30 °C Temperature Accuracies: ±2-3°C Temperature Rate of Change: 20-25 deg /min (Non-linear) Maintenance Free Access to The System Self-Sufficient System Compact with small footprints suitable for any space constraint laboratories Low decibel system Suitable for testing electronic chips / devices Environmentally friendly refrigerants Efficient heating Microprocessor based single set point PID temperature controller with data logging Flexible hose up to 2.5-3.0m Interchangeable heads according to chip size. Inbuilt electrical control panel with switchgear system
-
Product
Needle Pressure Gauge
102
-
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
Product
Pneumatic, Contact, Receiver, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610131104
Pneumatic Contact (Receiver)
Primary mating contact 610132104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
Product
Pitot Static Tester
ADSE 643
-
The ADSE 643 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fixed and rotary wing.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The ease of use and portability enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.The test set is housed in an anodized metal and rugged case.An attached case contains the pressure hoses and electrical cables.
-
Product
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules
610132106
Pneumatic Contact (ITA)
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules.
-
Product
Portable Small Meter Tester
-
The Portable Small Meter Tester (PSMT) is a lightweight system for field testing of 5/81 in. meters. It includes a test meter with control valves, hose connections, fittings and pressure gauge. Meter tests can be done without removing them from service. The inlet control valve ensures an accurate test start and stop. A globe valve downstream from the meter allows flow rate adjustment during test. Connection to the PSMT is made using standard 3/4 in. male hose connections located on the exterior of the case. Two 3/4 x 39 in. metal-reinforced flexible hoses are provided for easy field connections.
-
Product
Safety Chamber, Hydrostatic Test
9901HTX-36x36x15
-
The 3 ft wide by 3 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
Product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-36x36x15
-
The 3 ft. wide x 3 ft. deep Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
Product
Portable Hydrostatic Hose Tester, 15000 psi; USMC
9901HT-8762
-
The 9901HT-8762 Hydraulic Hose Test System is utilized by the United States Marine Corp. for their portable forward base maintenance stations. The system includes it's own onboard "quiet" air compressor and a set of 37 degree flared test adapters from 3/16" through 2" as well as an onboard calibration gauge and pneumatic castors for use on rough terrain.
-
Product
Pitot Static Tester / AoA TESTER
ADSE 744
-
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to create a differential pressure between the 2 Ps Channel, allowing to performsimulations of different Angles of Attack. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The ADSE 744 is robust and housed in amobile weatherproof case. An attached bag contains the pressure hoses and electrical cables.
-
Product
Pressure Pumps, Fittings And Hoses
-
Practical Instrument Electronics, Inc.
Choose from 3 different pressure pumps depending on your requirements. All pumps are rugged metal construction with 2 outlet ports for connections, a fine adjust piston and a precision pressure vent. Pumps come standard with one 3′ 6900 PSI hose and a 1/4″ male NPT fitting.
-
Product
Heavy Duty RV Tire Pressure Gauge
-
DURABLE BUILD: Superior quality steel and components are protected by a rugged rubber guard; Tough, anti-slip grip holds up to any job; Built tough to measure from 0-230 PSI with accurate readingSPECIALIZED CHUCK: Extended chuck tip to form a great seal with no air leakage; Dual-head air chuck painlessly reaches all your vehicles' valves from any angle; Durable rubber hose and an extended head chuck make it easier to get a good fit on awkward valves
-
Product
Heavy Duty Compression Tester for Gasoline Engines
34300
-
Use to test compression of gasoline engines on domestic and foreign cars and trucks plus motorcycles, snow mobiles and lawn mowers.Adapters provided for 10mm, 12mm, 14mm and 18mm applications.Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold.Screw-in adapters provide better accuracy over push-in type testers.Quick disconnect for easy hook-ups.Quick side release valve permits retests without removal of adapters.
-
Product
Petrol Engine Compression Tester 0-300Psi/0-21Bar
DCT1
-
Suitable for use on most petrol-engined vehicles including motorcycles. Comprises 300mm flexible hose, with 14mm and 18mm threaded adaptors, large easy-to-read scale (0-300psi/0-21bar) and air release valve to allow rapid retesting.
-
Product
8-Pin Pneumatic Block | Receiver Side
-
8-pin pneumatic block | receiver side, Equipped with KSV-PK-3 (462011), Grid dimensions 10-11mm / 12-13mm, 4mm hose, Plastic: With socket contact with shut-off HAN compressed air socket (278256)
