Reference Transmitters
high quality optical transmitters for test and measurement.
See Also: References, Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Acoustical References, Frequency References, Solar Reference Cells, Fiber Optic
-
Product
Temperature Thermowells, Sensors & Transmitters
-
Rosemount temperature products have been recognized for leadership in the process industry. As your trusted temperature partner, Emerson delivers factory-tested, ready-to-install temperature assemblies. With our industry leading portfolio of transmitters, sensors and thermowells, we provide reliable solutions for your temperature applications.
-
Product
PSS Portable Oxygen Transmitter
OxyTrans-PSS
-
The OxyTrans-PSS uses a special micro-fuel cell to measure the oxygen concentration. The sensor meets the industrial requirements for accuracy, sensitivity, easy to use and has a long operating life.The calibration of the instrument for trace oxygen measurements in gas should be done with a known calibrated gas. The concentration can be chosen freely within the measuring range.
-
Product
Humidity and Temperature Transmitter
T3111Ex
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Audio Frequency Transmitter
TG 20/50
-
Cable fault location with the BAUR TG 20/50. The TG 20/50 is a portable, battery-operated audio generator with a built-in charging unit. Together with the UL audio frequency receiver and the SP detecting rod, the TG 20/50 is used for cable tracing, twist method and for determining the depth of cables and metal pipes.* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output* Two output frequencies selectable
-
Product
Contact Level Transmitters
-
Measure level of liquids, pastes, granulates, powders, and liquid interface
-
Product
Reference Grade Compact Audio Interface
Lyra 1
-
Lyra represents the pinnacle of compact audio interfaces. Packing Prism Sounds trusted, uncompromising AD/DA conversion into a compact chassis perfect for use in the studio or on the road.
-
Product
Shunt Voltage References
-
Analog Devices offers a broad line of shunt precision voltage references that combine excellent accuracy and temperature stability with low noise and small packages. These devices operate in a manner that is functionally equivalent to a Zener diode. The bias current must be set higher than the sum of the maximum quiescent current of the voltage reference and the maximum expected load current. Since shunt voltage references are typically biased with a resistor, the voltage reference can operate on a wide range of input voltages.
-
Product
950~2400MHz DVB-S 4 ways SAT-IF CWDM Optical Transmitter & Receiver
HDBS-4000CW
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDBS-4000CW series is integrated 4pcs of SAT-IF CWDM standard wavelength optical transmitters with optical receivers in a casing. Through CWDM, Transmitter 4 ways optical multiplex (TX) or demultiplex (RX) through one fiber. It can be well used in transmitting a satellite VL, VH, HL, HH different polarize 4 way SAT-IF signal. It can be easily operated.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Differential Pressure Transmitter
DPA Series
-
Adtek has multiple transmitters which can be applied on different types of work environment. To have a better quality of life, buildings with central centilation system (CVS) become a trend, so we recently developed a new product, DPA, indoor differential pressure transmitter. The users can set up the measured range according to the actual use, and make zero adjustment for the differential pressure. Besides being equipped with regular analog outputs, we also added RS-485 output to DPA which is a simple and low cost communication tool connecting with monitoring system.
-
Product
Laser Level Transmitters
-
ABB is a leading manufacturer of state-of-the-art level and volume instrumentation for liquid and bulk solids detection. The family of non-contact laser volume and level products, LLT100, LM80, and LM200, provide solutions for accurate measurement in the following applications: inventory in bunkers, blending hoppers, reactor vessels, level control, volumetric measurement, and various dry bulk solids and liquids in silos.
-
Product
Universal Transmitter
Model LXT-330
-
Teledyne Analytical Instruments
Model LXT330 Liquid Transmitter is a single or dual channel, universal, multi-parameter transmitter, designed for continuous online liquid measurements. It is paired with SP3 Smart sensors and is intended for use in non-hazardous, general purpose rated industrial environments. The SP3 sensor platform covers a wide range of liquid analytical measurements, such as pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity, resistivity and turbidity. The LXT330 transmitter can be used with any SP3 smart sensors without additional user reconfiguration. The Universal Transmitter & Smart Sensor loop philosophy removed the need to stock for multiple instrument types. The process parameter, sensor details, serial number and calibration history are stored in the sensor's main memory, facilitated by two-way digital communication between the sensors and transmitter. The LXT330 universal transmitter allows for up to two SP3 sensors per transmitter (contact factory for available combinations).
-
Product
Dew Point Meters & Transmitters
-
Dew point and moisture content plays a large role in the quality, shelf life, pricing, weight, and ability to process many products. Our COSA Xentaur dew point meters are easy-to-use moisture analyzers ideal for quality control, production and in-process control of many industries, such as pharmaceutical, chemical, plastics, and the food and beverage industries. With user-friendly interface, our multi-functional dew point meters are fast and accurate with low maintenance.
-
Product
Barometric Pressure Transmitter
T2314
-
Barometric pressure transmitter for outdoor and indoor use.Display reading and pressure output is user selectable in these units: hPa, kPa, mbar, mmHg, inHg, inH2O, PSI, oz/in2.
-
Product
Industrial Pressure Transmitter
628
-
The Dwyer Series 628 Pressure Transmitters are ideal for OEMs with 1% full scale accuracy sensors. The transmitter is also available in the general purpose stainless steel housing and the cast aluminum conduit housing.
-
Product
Microwave Wideband Direct Modulated DFB Transmitters (without RF Amp)
MT50 (40KHz~20GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT50 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
Product
Temperature & Humidity Transmitter
HTO
-
- CO2 measuring element: NDIR Sensor 2- CO measuring element: Electrochemical sensor- Temperature/Humidity sensing element : CMOS sensor- Analog output option:4~20mA or 0~10V- Communication output option:RS485 Modbus RTU- Configured by PC with free software via USB cable (option)- Present value offset adjustable- Inside buttons for adjust output parameters- LCD backlight color to Indicated CO/CO concentration 2- Temperature measuring range can be -50~100℃ via USB console port to setting
-
Product
Reference Coordinate Measuring Machine
XENOS
-
XENOS from ZEISS features two linear drives in the Y direction, which are synchronized via a new technology developed by ZEISS: the central drive. It ensures optimal force distribution of the drives depending on the position of the X axis.
-
Product
CATV Fiber Optic Transmitter W/ Customer Specified ITU Wavelength
MX- T8500T-HP Series
-
The MX-T8500T-HP series externally modulated transmitter with ITU specified wavelengths delivers high performance signal transmission of NTSC, PAL, digital or compressed digital signals from 50-862 MHz for CATV applications.
-
Product
Transmitter / Receiver Modules
-
An RF module (radio frequency module) is a (usually) small electronic device used to transmit and/or receive radio signals between two devices. In an embedded system it is often desirable to communicate with another device wirelessly. This wireless communication may be accomplished through optical communication or through radio frequency (RF) communication. For many applications the medium of choice is RF since it does not require line of sight. RF communications incorporate a transmitter and/or receiver.
-
Product
COM Express® Type 2 Reference Carrier Board in ATX Form Factor
Express-BASE
Computer on Module
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
Product
Weatherproof Pressure Transmitter
682
-
The Series 682 Industrial Pressure Transmitter is designed to withstand environmental effects such as shock, vibration, temperature, and EMI/RFI. The electronics and capacitive sensor are packaged in a welded stainless steel housing and meets NEMA 4 (IP65) protection ratings.
-
Product
Transmitter Monitors Carbon Monoxide
CO-R
-
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
Product
Humidity transmitters for HVAC
-
Humidity transmitter for heating, ventilation and air conditioning technology. Humidity transmitters for building technology are also available as OEM versions in custom designs.
-
Product
Optical Transmitter
ST1013-3mW
-
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home)Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices *Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
Product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
Carrier Board
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Wireless Transmitters
-
Omega wireless transmitters are weather-resistant and are designed to deliver a wide range of data such as voltage, current, temperature, humidity, barometric pressure, and pH.
-
Product
950~2400MHz DVB-S 4 ways SAT-IF DWDM Optical Transmitter & Receiver
HDBS-4000DW
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDBS-4000DW series, combine 4 pieces C-Band, 100GHz, ITU standard wavelength SAT-If optical transmitter, or optical receiver to one chassis, through DWDM, Make 4 ways optical MUX (TX) or DEMUX (RX), through one fiber, used in transmitting 4 ways different polarization SAT-IF signal of one satellite VL, VH, HL, HH with high performance. Installation flexibility.
-
Product
VoLTE Battery Test, Reference Solution
-
The VoLTE Battery Test, Reference Solution is a fully automated test solution for chipset vendors and device makers who need to follow operators’ VoLTE battery acceptance test plans.
-
Product
Transmitter Control Subsystem (TCS)
Loran C Accufix 7500
-
USCG Loran Transmitter Control and Display stations modernized and upgraded to state-of-the-art processor controlled technology. Fully redundant system with comprehensive built-in performance monitoring. Automatic switchover upon detection of error, high single point failure tolerance. Long distance communications link supports remote station operation on a continuous basis. Built-in fault detection and monitoring enables dynamic re-allocation of failed subsystem modules, and fault isolation to major replacement assemblies.
