Board Test Fixtures
jigs which hold, align and engage pcb with test interconnect.
See Also: Fixtures, Test Fixtures, Bare board Fixtures, PCB Test Fixtures, Genrad Fixtures
-
Product
SMARC 2.1 Reference Carrier Board with M.2 Extension
I-Pi SMARC Plus
Carrier Board
The I-Pi SMARC Plus is small (110mm x 110mm) SMARC reference carrier board based on SGeT SMARC (Smart Mobility ARChitecture) 2.1 hardware specification. Together with the SMARC short size module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
End of Line Test System for Automotive Seats
AS519
Test Platform
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
Product
In‐Circuit Test Fixtures
-
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
-
Product
Manual Test Press Fixture
750/752 Series
-
RTI's manual test presses are compact, portable, all-inclusive, and easy to use. Single lever operation and 100% vertical compression makes the manual test press an ideal solution for PCB, hybrid module, and high pin count device-level testing when complex test requirements cannot be met with a test socket and breakout board alone.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 15,50 kg
-
Product
Extreme Rugged PC/104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM1-BT1
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
Lower-Cost Small Footprint In-Circuit Test System
TestStation LHS
In-Circuit Test System
The TestStation LHS in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne’s popular, award winning TestStation product family. Compatible with existing TestStation LH fixtures.TestStation LH features the voltage accuracy and backdrive current measurement embedded in Teradyne’s SafeTest protection technology for accurate, reliable and safe powered-up testing of new low-voltage software.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
Hi Potential & Cable Continuity Test Fixture
310HIPOT
-
The most important features of this hipot tester fixture is its safety and ease of use intuitive control functions and durability in a production environment.
-
Product
NTS Platform
Test Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
Product
Memory Test System
T5833/T5833ES
Test System
T5833 system is a cost-efficient, high-volume test solution capable of performing both wafer sort and final test of DRAM and NAND flash memory devices. Amid surging sales of mobile electronics, DRAMs, NAND flash memories and multi-chip packages (MCPs) — the main device types used in smart phones and tablets — are quickly evolving toward higher speeds and greater device capacity. Internet and cloud servers also are driving demand for faster, higher-capacity ICs. Yet the cost of testing today's wide array of memory devices is an obstacle for chipmakers, which urgently require solutions that can deliver high functionality, high performance and low cost of test (COT). Advantest's new, multifunctional T5833 memory test system meets these needs, delivering both wafer sort and final test capabilities for a full range of memory devices, including LPDDR3-DRAMs, high-speed NAND flash memories and next-generation non-volatile memory ICs.
-
Product
Semiconductor Test Software
Test System
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
UIO40-Express Series
UIO-4030
Digital I/O Board
*1 2 wires RS-232*1 RS-485*8 GPIO (-24~24V input)
-
Product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
Product
Custom Fixtures
-
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
Product
HTOL Test Systems
Test System
Our IOL & Power-Cycling systems increase measurement quality & throughput while simultaneously reducing the Total Cost of Test (TCoT) of an open platform. We focus on complete monitoring and precise temperature control for each device under test.
-
Product
Drop-In Functional Test Fixtures
-
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
Product
Compact & Flexible Test Systems for FCT,ICT, ISP and Boundary Scan Designed for Easy Integration
LEON Rack
Test System
The LEONRack test system is a flexible test system that could be installed in automation or handling solutions. It is highly flexible and available in three different chassis sizes from low pin count to high pin count test systems. As part of the LEON Family, LEONRack is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
PCB Test Fixture Kits And Customized Fixtures
-
Mirotech manufactures portable benchtop PCB test fixture kits and provides customized test fixture solutions for the electronics industry. Our innovative, streamlined designs are compact in size and feature a linear collapsing system, interchangeable and reusable plate design, top and bottom probing, and are affordably priced. All fixtures are built using high quality hardware and materials and manufactured using the DATRON M8Cube, known for its precision and accuracy. Each of our custom designs are unique to our customer’s particular project requirements. Fixture kits come pre-assembled, and include blank plates ready for you to drill your test pattern.
-
Product
Meter Test Board
MTB
-
The accuracy of TESCO’s Meter Test Board (MTB-3050) is now available in multi-position test boards to perform individual or simultaneous accuracy tests in the meter shop!
-
Product
Conformance Test System
TS-RRM
Test System
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
Product
Test fixtures
-
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
Product
Automated Test Equipment
test
These systems test semiconductor performance and quality with industry-leading precision and cost efficiency. Robust support for semiconductor design evaluation, volume production ramps, and yield improvement.
-
Product
Universal In-Line Test Platform
Test Platform
UniLine brings 20+ years of test & quality experience to your manufacturing floor and test automation delivers accurate results, without bias. By standardizing test, product quality improves as costs decrease. Equipment becomes understandable and manageable across departments and station support becomes simple.
-
Product
Single Board Computers
Single Board Computer
NAI offers a comprehensive line of adaptable, 3U cPCI, 3U VPX and 6U VME, rugged Single Board Computers (SBCs) specifically designed for harsh, SWaP-constrained environments in a range of demanding, embedded computing applications for the defense, commercial aerospace and industrial applications. These Commercial Off-the-Shelf (COTS) and modified COTS SBCs are based on the latest Intel®, NXP (PowerPC™), and ARM® Cortex®- A9 processors, each delivering unique advantages in deployed applications.
-
Product
Thermal Test Boards
-
Thermal Engineering Associates, Inc.
TEA offers a series of thermal test boards for package characterization and design comparison that conform to to the JEDEC JESD51 standards. The board family, referred to as the TTB-1000 series, consists of two different standard sizes designed to cover a wide range of package sizes. These boards, also referred to as test coupons, provide a well defined mounting environment, will withstand temperatures to 125 oC, and have lead lands terminated in eyelets to allow for hand-wired connection to the board edge contacts. The board mates with a dual 18-pin, 3.962 mm (0.156") pitch edge-card connector.
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
Modular Functional Testing Platform
OTP2
Test Platform
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
Product
Test Fixture with API
TA-14VG
-
The TA-14VG test fixture is based on the requirements for the Integrated Test Procedure for the VG-14A assembly as shown in the OEM maintenance manual. The panel also contains a test point breakout for the units main connector as well as one for the VG-401 base. The VG-401 breakouts provide an in series connection that will allow easy access to the gyro's signals and also provides a way to monitor rotor current. The panel also contains a variac to allow for line voltage adjustment.
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
