Softness
describes how yielding a material is to pressure, touch for example.
-
Product
PXI Relay Module
Relay
PXI Relay Modules consist of multiple independent relays, such as single-pole single-throw (SPST), single-pole double-throw (SPDT), and double-pole double-throw (DPDT) relays. PXI Relay Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a set of relays that fit your requirements. To program the relays, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
Single-ended, Direct Connect Probe, 34-Channel, 4 X 160-pin
U4206A
-
The U4206A is a direct-connect probe/cable with a standard soft touch pro connector at one end that routes to four 160-pin connectors that plug into the front panel connectors of a U4164A logic analyzer module. The U4206A is designed to be used with either the quad state mode or ¼ channel 10 GHz timing mode of the U4164A logic analyzer module. For use in quad state mode only, the U4206A includes two flying leads to connect additional clock qualifier signals into the clock inputs on Pods 3 and 7. Please refer to the U4164A installation guide for specific details on the operation of the U4164A quad sample state or ¼ channel 10 GHz timing modes of operation.
-
Product
Rectal Probe For Humans, Larger Animals
RET-1
-
The RET-1 Rectal Probe for humans, neonatal rabbits, and larger animals. Flexible vinyl covered, soft tipped. 5 foot lead (can be made longer), 5/32'' max. tip diameter, max lead diameter 3/32''. Time constant 5.0 seconds.
-
Product
Passive Oscilloscope Probes
5900 SERIES
-
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
-
Product
Anaerobic Jar Tester
LD-LAJ-A11
-
Anaerobic JarLD-LAJ-A11with 2.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
Product
Low-Temperature Impact Device
DWC-1
-
This low-temperature impact device is compliance with standard requirement of IEC60245, IEC60227, IEC60540, GB5013-2008, GB5023-2008 and GBT2951-2008. It’s used to test all kinds of PVC sheathed cable, wire, soft wire and no sheath of parallel soft PVC insulated impact resistance at low temperature. Specification: • Working temperature: -15℃±1℃ • Impact height: 10~200mm adjustable • Length of specimen: 5D~150D • Material: 304 stainless steel • Completion time once: 3~5s • Completion number of units for once: ≥2pcs • Weight: 100/200/300/400/500/600/750/1000/1250/1500g • Low temperature box to match additionally
-
Product
Hardness Testers
-
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
Product
ARINC 429 Test And Simulation VME Module
VME-429
-
*8, 16, 32 or 64 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
EMX-7XXX
Programmable Resistor Module
The AMETEK VTI Instruments EMX-7000 Series PXIe Precision Programmable Resistor Ladder modules provide four independent channels of programmable resistors. The EMX-7004 is capable of delivering exceptional stability and accuracy for any resistance value between 1 Ω to 16,383 Ω and can be adjusted in 1 Ω increments through the software application programming interface (API) or dynamic soft front panel.The EMX-7005, EMX-7006 and EMX-7007 are perfect for applications requiring higher resistance values, with programmable settings ranging from 163 kΩ to 16.383 Mohms, while the EMX-7014, 7015 and 7016 are ideal for general purpose applications not requiring ultra high accuracies.
-
Product
BF-Series Standard Models
-
The E-DRIV® BF-Series standard models feature an adjustable RPM setting on the tool and a selectable Soft Start mode. Engineered for high volume manufacturing applications the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
Instrumented Indentation Tester
-
With Anton Paar’s versatile indentation testers you can precisely determine the mechanical properties of thin films, coatings, or substrates such as hardness and elastic modulus. The instruments handle almost any type of material, whether soft, hard, brittle, or ductile. You can also conduct creep, fatigue, and stress-strain studies on surfaces in the nanometer range.
-
Product
Static Electricity Measurement Management Set
NK-1B / NK-2B
-
We have all the measuring instruments for solving ESD troubles.It is easy to carry and is ideal for process diagnosis.You can send it as it is by courier.Ideal for in-house static electricity education.A special soft case is attached so that the measuring instruments can be carried individually.
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
ProLink to ProBus2 Adapter
LPA-PBUS2
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range-Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
18-Slot LXI Modular Switching Chassis
60-103B-001
Chassis
This 18-slot LXI Chassis is fully compliant with the LXI Standard 1.4 and allows the large number of our 3U PXI modules to be installed and controlled through a standardized Ethernet interface. Each module is supported as though it is an LXI compliant device, complete with a driverless soft front panel that provides control of the module functions.
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
Analog TV Analyzer
BT-QAM-PRO
-
Blonder Tongue Laboratories, Inc.
The BT-QAM-PRO is an economical feature-packed test instrument for analyzing CATV QAM and Broadcast 8VSB digital channels, as well as NTSC analog channels. This compact instrument is designed with field service technicians in mind and provides many of the features that are typically only found in many higher-priced units. The BT-QAM-PRO comes complete with a soft water-resistant case and a micro USB charging/PC cable.
-
Product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
-
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
Product
SIMRC - Carrier Kit
1050-002
-
The SIM Relay Carrier 1050 simplifies the custom integration of small format embedded switching cards. No additional PCB design is necessary. Due to the Eurocard format the carrier can be fitted into a standard case or can be mounted in a 19" rack with side rails. Plug in standard SIM Relay Cards and control your switch application with the provided Soft Front Panel without any additional programming.
-
Product
Sonin Digital Moisture Meter 270
50270
-
This compact easy-to-use Digital Moisture Meter is ideal for anyone needing to measure the moisture content in soft and hardwoods including tropical species.
-
Product
Specialty Testers
-
Test Voltage from 120V to 600V AC/DCNon-Contact Voltage Sensor from 90V to 1000VTest Continuity & PolarityCase serves as prod holder for one-hand operationSelf-storing prodsSolenoid Sensing indicated by LEDs & VibrationErgonomic Soft PVC housing for comfort gripLED Spotlight Illuminates Work AreaBattery not Included (AAA x 1)
-
Product
Measuring Devices for Magnetically Soft Materials
MAG-RJJ-6.0
-
The computerized measuring system is designed for measure the dynamic magnetic properties of the soft magnetic materials e.g. oriented or not-oriented electrical sheet. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter.
-
Product
Ammeter
AC Moving Iron Meter
-
Moving-iron instruments are generally used to measure alternating voltages and currents. In moving-iron instruments the movable system consists of one or more pieces of specially-shaped soft iron, which are so pivoted as to be acted upon by the magnetic field produced by the current in coil.
-
Product
Controller
YFC
-
The YFC-35D operates with only the YF-Series brushless electric screwdrivers. It is a single tool controller that offers programmable speed, angle, auto reverse and soft start options. The controller provides programmable fastening options for sequence based assembly automation applications.
-
Product
Portable Thermal Conductivity Meter
TLS-100
-
The TLS-100 is a portable thermal conductivity meter used to measure thermal conductivity and thermal resistivity at the push of a button. Each TLS-100 comes equipped with a 100 mm sensor for testing soil, polymers, and other soft materials. An optional 50 mm sensor was designed for testing harder materials, like rock and concrete. The collected data is automatically analyzed, and results are displayed instantly.
-
Product
Cable and Antenna Analyzer
iVA-0627A-NC
-
iVA Cable & Antenna Analyzer System, Type N male connector with Neoprene Soft Case
-
Product
100 N Pantograph Grips
-
Pantograph grips use a simple spring design to hold and apply pressure to specimens during tensile testing. These grips are mainly used for tensile testing plate specimens of rubber, textiles, or soft plastics.
-
Product
Combo Unit, 7.5 Digit Digital Multimeter (DMM) with 10-Bit 1GHz Digitizer in a Single VXI Slot
6084A
Digitizer
Increases test system performance and density with this combo unit, which packages a 7.5 digit Digital Multimeter (DMM) together with a 10-bit, 1 GHz Digitizer into a single VXI slot.Replaces the Wavetek 1362 DMM, Analogic DBS Series, and Agilent VXI DigitizersDigitizer with 4 Inputs, 10-bits, 1 GHz, up to 4 GS/s and Ranges up to 500V DMM with 7.5 Digits for DC Volts, Current and Ohms with AC Volts up to 1 MHzIVI-COM Drivers and Soft Front Panels ProvidedMore Dynamic Range (by 20 dB for DMM and 12 dB for Digitizer) for Better Legacy Range Mapping
-
Product
Handheld Laser Power & Energy Meter
Vega 7Z01560
-
*Compatible with all standard Ophir Thermopile, BeamTrack, Pyroelectric and Photodiode sensors*Brilliant color large size TFT 320x240 display*Clear screen color for work with laser safety goggles*Illuminated keys for working in the dark*Both digital and analog needle display*USB and RS232 output to PC with Statistics package*Select between English and Japanese interfaces*Analog output*Soft keys and menu driven functions with on line help*Log every data point at up to 4000Hz with pyroelectric sensors*Non-volatile data storage up to 250,000 points*Laser tuning screen and power log*2 position kickstand*System Integrator Tools included: LabVIEW VIs, COM Object Interface
-
Product
Fume Hood Testing
-
Test mannequin to simulate a human breathing zone. Comes with a manikin, lab coat, manikin stand, and soft carrying case.
