Softness
describes how yielding a material is to pressure, touch for example.
-
Product
Measuring Devices for Magnetically Soft Materials
TMAG-RJJ-3.1
-
The system is a mobile version of computerized measuring system MAG-RJJ-6.0 and is designed for measure the dynamic magnetic properties of the soft magnetic materials e.g. oriented or not-oriented electrical sheet. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter. The system works under Windows 2000/XP.
-
Product
Line Monitor
LE-120SA
-
LE-120SA is a handheld line monitor specialized for ASYNC communication which is widely used in the industry. You can control the line monitor by soft screen touch as you do for smart phones. The light weight (300g including batteries) helps you for the field maintenance besides the system developments.
-
Product
Tire Durometer
Model 2100
-
Tire hardness can be a critical factor in setting up a race car. A tire that's too hard may sacrifice traction, while a tire that's too soft may give great traction but wear too quickly, and an unmatched set of tires may result in an ill handling car. To properly set up a car, a measure of tire hardness is necessary, and the easiest and most cost-effective way to obtain such a measure is to use a durometer.
-
Product
Loggers/PQA
-
Kyoritsu Electrical Instruments Works, Ltd.
Large capacity for storing 60,000 data points Lowpass Filter will filter out the harmonics LED flickers when the preset current/voltage value is exceeded CALL:Confirmation of recorded data Selection of One-time mode or Endless mode Non Volatile Memory Battery power indicator The userfriendly PC software "KEW LOG Soft 2" is supplied Continuous measuring time:Approx. 10 days (Alkaline Battery)
-
Product
Type 1 And Type 2 Pantograph Grips
-
Pantograph grips use a simple spring design to hold and apply pressure to specimens during tensile testing. These grips are mainly used for tensile testing plate specimens of rubber, textiles, or soft plastics.
-
Product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Paper Testing Instruments
-
Whiteness and chromaciticity tester, whiteness meter, tensile stiffness tester, automatic horizontal tensile tester, automatic horizontal tensile tester, vertical tensile tester, pulp beating (refining) freeness tester, water absorbtion tester, Cobb tester, COBB sample cutter, coefficient of friction tester, electronic bending stiffness tester, paper and cardboard thickness meter, paper and cardboard thickness meter, ink rubber tester, standard strip cutter, softness tester, carton compression tester, paper air permeability tester, internal ply bond tester, puncture strength tester, paper tearing tester, electronic tearing tester, mullen burst tester, crush tester, Bekk smoothness tester, folding endurance tester
-
Product
Handheld Capacitance and LCR Meters
U1700 Series
-
The U1731C/32C/33C LCR meters allow you to measure frequencies as high as 100 kHz, a capability typically found only in benchtop meters.Gain better noise immunity and save money with Option-SMD. Each of the order comes with an Option-SMD that consists of a handy soft carrying case and SMD tweezer for better value of your money. The SMD tweezer is suitable for making measurements on SMD components and is used with the guard terminals on meter for better noise immunity.
-
Product
D.C. Recording Fluxmeter
TRF
-
This is the equipment being able to measure direct current magnetization property of wide-ranging magnetic materials from soft magnetic materials to high performance permanent magnet with magnetic flux meter based on M integral closed magnetic circuit system.
-
Product
Soft Touch Micro
-
Variable measuring force type‚ optimal for measuring soft materials Two different measuring force types are available according to the purpose.
-
Product
Gratings for Synchrotron, FEL and EUV Light Sources
-
HORIBA Scientific holographic lamellar gratings exhibit ultra-low grooves roughness and unique efficiency uniformity making them ideal for Synchrotron, Free Electron Laser (FEL), EUV or Soft X-ray light sources.
-
Product
WaveLink Dx20-PT Adjustable Positioner Tip Kit
Dx20-PT-KIT
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
LXI Microwave Multiplexer, 50Ω Dual 18-Channel 6GHz SMA
60-891-019
Multiplexer Module
This LXI Microwave Multiplexer is controlled through an LXI interface based on 1000Base-T Ethernet. This provides a quick and easy method of installation. It also provides a simple way of controlling it at a remote location through its API or built in soft front panel.
-
Product
Preset Torque Screwdrivers
PSE
-
The PSE is a preset torque screwdriver (internally adjustable) that delivers precision torque control. Built with a cam-over design, the accurate torque screwdriver prevents a fastener or bolt from being under and over tightened. Featuring a soft textured grip, the torque driver is an ergonomically safe tool for the operator to use and is ESD compliant. Using a quality torque screwdriver ensures that proper torque is being applied and maintains requirements associated with ISO quality standards.
-
Product
Sample Pretreatment For Optical Emission Spectrometry
-
Samples are taken from molten metal, thin sheet, semi-complete or complete products. When sampling molten metal with a ladle, small quantities of molten metal are poured into a casting mold. Unnecessary parts of the sample are removed using a grinder or a cutter. As particles from a grinder may contaminate the surface of the sample, a lathe or milling machine is used (not a grinder) to cut soft samples such as white metal. If trace elements are not being investigated, a grinder or belt sander can be used. However, to minimize contamination, the grinding wheel or belt should be changed for each sample. Samples excised from semi-complete or complete products must be at least 12 mm in diameter. Small rod-shaped samples can be analyzed using special equipment.
-
Product
Open Flanges Test Rig
-
Flexible cell dimensions: cells of Ø 8 to Ø 80 mm (or square till 70x70 mm) can be successively installed Quick start of experiment: less than 20 minutes to remount a new cell with different dimension, thanks to the simple design without sealing Other SOFC components: the open flanges test rig is also useful for conductivity measurements (electrolyte, electrode material, interconnect etc.) and sealing tests End of broken cells and secure testing: the cell is squeezed by a soft alumina felt that prevents any damages, the excess fuel burns continuously in the alumina felt at the cell edges
-
Product
Soft Carrying Case And Front Panel Cover For 2000 And 3000 X-Series Oscilloscope
N6457A
-
The N6457A Soft carrying case is the perfect way to travel with or store your 2000 or 3000 X-Series oscilloscope. The case is designed for convenience with padded sides and bottom, as well as a storage pouch for your probes and additional accessories.
-
Product
Shore Hardness Tester
HT-6510
-
Application: shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials. Shore D is designed for plastics, Formica, Epoxies and Plexiglass. Application: shore C is designed for various foam and sponge.
-
Product
Anti-Fogging Progerty Tester
-
Shijiazhuang Zhongshi Testing Machine Co., Ltd.
The instrument is used for testing anti-fogging property of the soft PVC Calendar stenter film. It is the ideal testing equipment for science research department, universities, commodity inspection, laboratory, graduate school and quality supervision departments.
-
Product
Deluxe Durometer with Case
52-50546
-
Longacre Racing Products, Inc.
Tire hardness has a huge affect on your car's performance. A tire too hard won't bite and a tire too soft may wear quickly or even ball up. Also tire hardness changes during its life cycle. To run your best you must keep track of all your tire's hardnesses.
-
Product
Soft Magnetic Core Power Loss Analyzer
SS-SML01
-
This SS-SML01 soft magnetic core power loss analyzer includes one set broadband power signal generator and on set W-A-V meter, the broadband power signal generator is specially researched and manufactured for the testing of the soft magnetism materials.
-
Product
Inline Beverage Analyzer
-
The inline beverage analysis systems are the result of more than 40 years of experience in inline and laboratory beverage analysis, based on thousands of samples covering the production of beer, wine, cider, FABs, juice, soft drinks, diet drinks, tea, and other beverages. Anton Paar is the leading manufacturer of inline beverage analyzers with custom-made solutions for all beverage applications, ready-to-use without time-consuming on-site adjustment. These beverage analyzers can be fully connected to your laboratory equipment to ensure in-spec production and complete traceability. First-class instruments for continuous, accurate, and safe measurements of important quality parameters, such as °Brix, %Diet concentration, CO2, alcohol, sugar inversion, extract, etc. during the whole production process.
-
Product
2U Family of Programmable AC-DC Switching Power Supplies to 1400W
-
The 2U family of programmable AC-DC power supplies sets a new standard for flexible and reliable power for your application. Available in a Rack Mounting or Benchtop at 1400W power levels with single output voltages ranging from 10 to 270V and current capabilities up to 120A. A user-friendly front panel provides reliable linear controls for finer adjustment and digital LED voltage and current meters. Standard features include; 'soft start' operation and 'no load' operation, thermostatically speed controlled fans to limit acoustic noise, short circuit and overload protection, thermal protection, internal EMI filtering, RFI shielding and remote sensing.
-
Product
Yoke
M-XY10
-
The JM-XY10 yoke is designed to measure dynamic magnetic properties of tested materials under alternating and rotational field. The measuring could by made on square samples (side: 60÷100 mm) or circle samples with diameter 60÷85 mm. The JM50 yoke could be cooperating with following equipment designed to measuring soft magnetic properties:
-
Product
Model V: Veneer Moisture Meter
MRC003304
-
Calibrated for 48 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 1/8 inch penetration.
-
Product
Soft Carrying Case, 4-5/7 In. D, Black
U1175A
-
Soft carrying case for U1200 series clamp meters; 4-5/7 in, black
-
Product
Esophageal Probe
ESO-1
-
The ESO-1 Esophageal/Rectal Probe for humans and larger animals. Flexible vinyl covered, soft tipped. 5 foot lead (can be made longer), 7/32'' max. tip diameter, lead diameter 1/8''. Time constant 5.0 seconds.
-
Product
AC Magnetism Measurement Equipment
TWM
-
This equipment is used for measurement analysis of magnetic characteristics in high frequency by commercial frequency of soft material sample such as magnetic steel sheet and amorphous etc., and for quality control of product and material research. It is possible to apply single sheet sample, ring type of sample and Epstein sample etc.
-
Product
Electromagnetic Immunity Scanner
SmartScan 350
-
Reproducing similar soft or hard failure to the gun test - Flexible automatic failure detection module - Susceptibility map generation- Automatic report generation- Flexible scan area editor (SAE)- Flexible display (3D, histogram)- Matlab support- Expandability (EMI scan, phase measurement, NFFF transformation)- Custom design probes
-
Product
Durometer - Shore Hardness Tester
-
Qualitest provides quality control departments and research laboratories with an extensive range of top quality Durometer and hardness Tester for accurate hardness determination on all natural and synthetic rubber products and soft elastic materials, plastics, acrylic glass, acetates, casting resin, polyester, thermoplastics, PVC, neoprenes, hardboards, wood, leather, fruits and much more. Our products provide the highest precision (normally 0.5% or better), quality and craftsmanship, durability, “yet require” almost no calibration in many years after the purchase. Our designs are engineered so that the Durometer stays precisely within the standard requirements. Qualitest Durometers are referred to as the “Swiss watches” among other products on the market. Investing in our line of Durometer is a guarantee of accuracy and assurance for many years of operation.
