Elemental
of the periodic table.
-
product
X-ray Fluorescence
XRF analysis – one of the best analytical techniques to perform elemental analysis in all kinds of samples, no matter if liquids, solids or loose powders must be analyzed.
-
product
LXI 1GHz 75ohm 32x8 Matrix
60-731-001
The 60-731 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-731 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
-
product
Primary Test Equipment
LET-1000-RD
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.The regulation system is based on a continuously variable autotransformer (Variac) that supplies to a power transformer that delivers the high current outputs and isolate the main supply from the load. A built-in ammeter and a timer gives the information about the current value and the operation time of the relay or breaker under test.
-
product
MultiPoint II Level Switch
The Multipoint II level switch product offers three control points located anywhere along a single vertically inserted level sensing element. One control point can be set up for differential measurement for pump control. This product is best suited to sump level control and batch processing.
-
product
LXI 1GHz 75ohm 8x8 Matrix
60-731-004
The 60-731 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-731 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
product
*Laser Thermal Power Sensors
Thermal sensors have a series of bimetallic junctions called a thermopile. Radial or axial heat flow through the sensor creates a voltage proportional to the power absorbed as it flows through the thermopile. The reading is not dependent on the ambient temperature since only the temperature difference is measured and not the absolute temperature. The thermopile elements are so arranged that the reading is almost independent of beam size and position. Generally, Ophir specifies ±2% or better uniformity of reading over the surface.
-
product
thermostats
Cooling bath circulation thermostats - freezing test set of equipment 2 pieces for carrying out the freezing test with 42-2260 .... Complete with insulated connection hoses and connection elements as well as integrated circulating pumps for temperature control of a single or double sample. The temperature setting is software-controlled. For connection, 2 separate fused circuits per 16 A are required.
-
product
Haptic testing
Haptic tests are becoming ever more important owing to the increasing and sector-independent popularity of switches and buttons in diverse products. More and more customers, especially in the automobile sector, attach great value to good haptic performance by their control elements. A precise switching feeling, low friction of the moving elements, backlash-free execution both in the rest position and during operation are only some of the criteria for good haptic switching characteristics.
-
product
Inductive Sensors
In general, inductive proximity switches consist of four basic elements: a coil, an oscillator, a threshold switch and an output stage with short-circuit protection.The oscillator generates a high frequency, electromagnetic alternating field which is emitted from the active face of the coil.Eddy currents are induced in a metal object that enters this field. These eddy currents draw energy from both the electromagnetic field and from the oscillator which is consequently attenuated.The more energy taken the closer the metal object moves towards the active face. The threshold switch switches on the output stage at a defined attenuation value.In proximity switches with a DC voltage supply, this switch is designed as an NPN transistor which switches the connected load to the negative pole or as a PNP transistor which switches the load to the positive pole. The output stage is a thyristor or a triac in AC voltage switches.
-
product
USAF Targets
These targets conform to MIL-STD-150A. Frequencies change by the 6th root of 2. This target is also available in custom sizes and contrasts. This test target meets requirements as specified in MIL-STD-150A for resolving power tests. The target consists of a series of Elements having two sets of lines at right angles. Each set of lines consists of three lines separated by spaces equal to the line width. Each bar has a length to width ratio of 5:1. (Line width is equal to one half of line pitch, which is the inverse of line frequency.) Elements are arranged in groups of six each and Groups are arranged in pairs. Even numbered Groups occupy the left side and bottom right corner and contain a square feature having and edge length equal to the line length of Element 2 in that group. Odd numbered Groups occupy the top right corner and side. Groups and Elements are labeled and differentiated by numbering adjacent to their features. Frequencies in cycles/mm (c/mm) increase between each Element by the sixth root of two (approximately 12.25% per step). The general formula for the line frequency of any target Element can be expressed as 2Group+(Element-1)/6.
-
product
Enclosures, Tripods, and Towers
Our sealed environmental enclosures help protect some of your station components from elements that may affect their ability to acquire and process your data. Our various structures and mounting equipment options help you group your components and physically support them for the continued optimal performance of your station.
-
product
4 Slot, 3U PXI/compactPCI Chassis
PDXI-4
PDXI stands for "PowerDAQ eXtensions for Instrumentation," and it moves both the CompactPCI and PXI worlds steps ahead in terms of technical performance as well as commercial considerations. Indeed, thanks to PDXI, users of both CompactPCI and PXI systems now have an alternate supplier for all hardware and software elements needed to construct a total system. Further, we ship completely preconfigured systems so that new users simply unpack the box, apply power, enter OS reg- istration numbers and start collecting data.
-
product
FEA Software
Helius PFA
Helius PFA software provides powerful tools for enhanced FEA (finite element analysis) of composite structures, including progressive failure analysis.
-
product
Single-Phase Static Switches
ISSF "PLUS"
The solid state switches ISSF “PLUS" exceed the limitations of electromechanical switches for many difficult and demanding applications, such as the control of high power motors, transformers, tungsten lamps, heating elements, electric furnaces, etc.
-
product
High performance multisensor
Werth StentCheck®
High performance multisensor CMM with Integrated Werth Zoom® optic with magnification 0.7x – 6.8xRotary/Tilt Axis with high speed air bearing rotary axisRotary OnTheFly for fast measurementsContour image processing for fully automatic measurements of complex geometrical elements with sub-micron repeatabilityIntegrated goniometer (tilting axis) allows for the measurement of non-cylindrical geometriesUnique lighting design optimized for measurement of stentsTemperature compensation included
-
product
Inductively Coupled Plasma Mass Spectrometry / ICP-MS Systems
Agilent ICP-MS systems utilize innovative technology to deliver excellent sensitivity, accuracy, ease of use and productivity. Our 7800 and 7900 quadrupole ICP-MS systems offer the highest matrix tolerance, widest dynamic range and most effective interference removal for trace elements across most typical applications. The 8900 Triple Quadrupole ICP-MS (ICP-QQQ) adds MS/MS operation, providing precise control of reaction cell processes to ensure the most consistent and accurate results, resolving interferences that are beyond the capability of quadrupole and sector-field high resolution ICP-MS.
-
product
Cement, Coal & Mineral Test & Analytical Solutions
Keep coal, cement, or mineral processing operations running efficiently, safely, and profitably. Thermo Scientific™ cross-belt online analyzers for cement and coal reduce process upsets and increase throughput with minute-by-minute composition analysis of ores and concentrates. Additionally, Thermo Scientific elemental and particle size analyzers for mineral beneficiation and flotation plants—when integrated with our sampling and analysis solutions—help you to increase the efficiency of your process.
-
product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Light
Welcome to Thorlabs; below you will find links to light emitters, sources, and controllers, a subset of our entire line of photonics products. Our light sources are conveniently separated into coherent and incoherent sources. The coherent source category includes laser diodes, laser diode modules, tunable lasers, HeNe lasers, and femtosecond lasers, while the incoherent source link brings you to a selection of LEDs, white light, and broadband SLD sources. The Quantum Electronics category includes optical amplifiers, modulators, and gain elements that are frequently used in research and OEM applications. All of our light sources and optical amplifiers are supported by an extensive line of mounts, sockets, TEC controllers, and current controllers.
-
product
Engineering Services
In addition to the highest quality test programming, maximizing board coverage, and efficient board testing, TTCI offers a full array of other engineering services, including CCA (Circuit Card Assembly) Testing, Design for Test, ASTER TestWay electrical design for test analyzer, Feasa LED analyzer, SMH Technologies FlashRunner in-system programmer, finite element analysus, installation, reverse engineering of Gerber to CAD, Training, Test System PC, Hardware, and Software Upgrades, and more.
-
product
PMC Module
XMC-603
Curtiss-Wright Defense Solutions
The XMC-603 PMC module allows customers to readily incorporate MIL-STD-1553 into military and aerospace embedded computing systems. As one of several products in our comprehensive range of rugged XMC modules, the XMC-603 integrates well with other elements of our product line, featuring technical support, lifecycle management services, and assured long-term availability.
-
product
Samrt Handy OTDR
TM290T
TM290T Smart handy OTDR is portable fiber fault locator, it is quickly to detect fault location and type of optical fiber using OTDR element and stronger software analysis tool.
-
product
Atomic Resolution Analytical Electron Microscope
NeoARM JEM-ARM200F
"NEOARM" comes with JEOL’s unique cold field emission gun (Cold-FEG) and a new Cs corrector (ASCOR) that compensates for higher order aberrations. The combination of a Cold-FEG and ASCOR enables atomic-resolution imaging at not only 200 kV accelerating voltage, but also a low voltage of 30 kV."NEOARM" is also equipped with an automated aberration correction system that incorporates JEOL’s new aberration correction algorithm for automatic fast and precise aberration correction. This system enables higher-throughput atomic-resolution imaging even at low accelerating voltages. Furthermore, a new STEM detector that provides enhanced contrast of light elements is incorporated as a standard unit.
-
product
X-Band Silicon Radar Quad Core IC
AWS-0105
The AWS-0105 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and single beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
product
Reticle Manufacturing
An error-free reticle (also known as a photomask or mask) represents a critical element in achieving high semiconductor device yields, since reticle defects or pattern placement errors can be replicated in many die on production wafers. Reticles are built upon blanks: substrates of quartz deposited with absorber films. KLA’s portfolio of reticle inspection, metrology and data analytics systems help blank, reticle and IC manufacturers identify reticle defects and pattern placement errors, thereby reducing yield risk.
-
product
Solar Radiation Sensors
The silicon solar radiation sensor (Si) sensor provides an inexpensive but yet robust and reliable solution for measuring the solar irradiance specifically for the monitoring of photovoltaic (PV) systems. Due to the structure of the sensor element, which corresponds to a PV module, these sensors are ideally suited as a reference for the monitoring of PV systems to determine the solar radiation.
-
product
Precision Gram Load Cell Universal/ Tension or Compression
GSO SERIES
The GS0 Series Load Cells can be utilized in tension or compression or both with excellent compliance. The force sensing end of the anodized aluminum GS0 Series is tapped 6-32 thru for attachment possibilities for almost any application. Bonded foil strain gages at the sensing element provide for excellent stability over the suggested temperature range and ensure long term reliability. Call for application assistance.
-
product
Hydrodynamic 33 kHz and 200 kHz Dual Frequency Transducer
Model TC2178
Model TC2178 is an optimized and hydrodynamic 33 kHz and 200 kHz dual frequency transducer ideal for navigation and hydrographic echosounder systems. The transducer has excellent piezoceramic elements which will ensure the highest reliability and quality in echosounding.
-
product
NI-9351, 4-Channel C Series Functional Safety Module
784446-01
4-Channel C Series Functional Safety Module - The NI-9351 works with 24 V industrial logic levels to directly connect to various sensor types, including light curtains, emergency e-stop buttons, and final elements such as relays, contactors, and motor drives. The NI-9351 is an analog input and digital I/O Functional Safety Module capable of SIL 3 certification according to IEC 61508. You can use the Functional Safety Editor to program the safety logic solver, which resides in the module. The module features diagnostics for monitoring the status of hardware and the integrity of the connections.
