Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
product
Inertial Systems
ACEINNA’s inertial systems provide end-users and systems integrators with fully-qualified MEMS-based solutions for measurement of static and dynamic motion in a wide variety of challenging environments, including; avionics, remotely operated vehicles, agricultural and construction vehicles, and automotive test.
-
product
PXIe-4139, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit
782856-02
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 20 W of DC power. This module features analog-to-digital … converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technolog...show more -
product
Test Socket
Our test sockets are made for high performance and are of top quality, to guarantee a smooth, effortless process. We believe in providing our partners and customers with effective and intelligent solutions that they can apply with ease. Choose the solutions of TTS Group cater to the needs of detailed and complex systems.
-
product
500Mz Spectrum Analyzer
SM-5005
Is used for the early test in the development of electrical products, troubleshooting of CATV/MATV system as well as the test and trouble diagnosis of cellular phone system. Combined with the near field probes of Mz530, it can detect the missing fields of radio frequency
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm
50-294-013
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Functional Test System
U8989A
The TS-8989 PXI functional test system is an integrated, all in one switch, load and measurement system in a box for high voltage or current mechatronics functional test applications of up to 104 nodes and 40A current loads.
-
product
Tempical® Tester
H394
Precision Testing For: Thermal Switches, Chromel®-Alumel® Thermocouples, and Continuous-Wire Fire Detection Systems.
-
product
Audio Analysis
The MCD AudioAnalyzer is used to test and calibrate analog and digital sound systems, or it can be used to convert analogue audio signals into digital form and vice versa. Also, the conversion of optical to electrical S / PDIF signals and vice versa can be done. The MCD AudioAnalyzer combines software (Toolmonitor MCD AudioAnalyzer) and hardware for the analysis and generation of analog and digital signals in the audio area.
-
product
CAN/LIN Interfaces - 2 Channel PCIe
OTP2 module no053
Expand your test system with the high-speed interface of the OTP2 module no053. The extension of the module can create new possibilities for your test system.
-
product
Water Brake Chassis Dynamometers
Chassis water brake dynos (also known as hydraulic dynamometers) can be operated continuously to resolve overheating, fuel mileage and drivetrain issues. Taylor’s eight models accommodating 50 to 1,100 hp at 40 mph enable testing of single-axle diesel pickup trucks, RVs and buses up through the largest tandem-axle on-highway trucks and buses. Tap into our deep product and applications knowledge to help you choose and make the most of the right water brake system for current and future needs.
-
product
xDSL PDH Analyzers
Wuhan Sunma Technology Co., Ltd.
xDSL / PDH Analyzer mainly used for comprehensive transmission test of SDH/PDH network and equipment and widely applied in the R&D, manufacture, acceptance inspection, performance monitoring, maintenance and measuring of networks and equipment. The instrument SunmaFiber provided can insert and measure varieties of errors and alarms in PDH and SDH systems (including on-line and off-line test), perform performance analysis on various errors as well as modulate and test jitter signals at a max. test rate of 2488MHz (STM16).
-
product
Dynamic IR Scene Projectors
Mirage™
In 1999, SBIR introduced MIRAGE™, the world’s first integrated Dynamic IR Scene Projection System, designed to support hardware-in-the-loop testing of missile seekers, FLIRs, counter measure simulation and tracking systems. MIRAGE™ is a complete turnkey infrared scene projector that utilizes unique resistive emitter array technology to produce high definition dynamic IR scenes. The original MIRAGE™-1 used a 512 x 511 pixel resistive array emitter capable of frame rates up to 200 Hz. Below is a list outlining the progression of the product line and a list of SBIR’s currently available scene generation systems:
-
product
AC Voltage Test Systems
HIGHVOLT Prüftechnik Dresden GmbH
AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
product
Pressure Test Points
Minimess
Minimess test points offer a uniquely simple method of accessing low or high pressure systems for the purpose of pressure testing, oil sampling or gas charging. Developed by Hydrotechnik more than 50 years ago, they are found worldwide in hydraulic, process and gas systems. These pressure test points offer the most advanced sealing system available with working pressures up to 630 bar.
-
product
Systems Integration (SIL) Lab Data Acquisition
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
-
product
PoE Voltage Monitor Detect & Verify
PE-400
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
product
Fully Automatic Full Load (Routine) Testing Panel For Induction Motor
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator. More then 500 Indian pump manufacturer ware installed this system & satisfied with performance.
-
product
HDD-8261, 4 TB, 6-Drive, PXI Data Storage Module
784191-01
4 TB, 6-Drive, PXI Data Storage Module - The HDD‑8261 in-chassis PXI Express high-speed data storage module features an onboard PCI Express SATA controller. The module fits into a PXI Express chassis, and it occupies only three PXI slots. With the HDD‑8261, you can choose between hard-disk drives (HDDs) or solid-state drives (SSDs) for increased ruggedness. It is ideal for field testing or signal recording applications. You can use this module to not only stream high-speed data, but also to easily move data between multiple test setups or supplement the PXI system controller’s storage capacity.
-
product
PXIe-1086, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), Up to 12 GB/s PXI Chassis
781720-01
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), Up to 12 GB/s PXI Chassis - The PXIe‑1086 incorporates hot-swappable, redundant AC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086 monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
product
DC Power Supplies
XG 850
AMETEK Programmable Power, Inc.
The Sorensen XG Series is an 850 Watt, 1U half-rack DC power supply. The XG Series is the new standard for powerful, programmable DC power systems. Designed for test, production, laboratory, OEM and quality assurance applications, the XG Series provides a wealth of features to ensure accuracy and greater efficiency. It puts clean, reliable power at your disposal and delivers stable, variable output voltage and current for a broad range of development, test and system requirements.
-
product
Analog Test Instruments
Analog test building blocks for high performance ATE. VXI-based Core System Instruments (CSi) ZT-Series™ PXI/LXI instruments.
-
product
NVM Express
NVM Express is a scalable host controller interface designed to address the needs of Enterprise, Data Center and Client systems for supporting chip-to-chip, board-to-board, adapter and distance solutions. The protocol can efficiently use interconnect and fabric technologies such as PCI Express, Ethernet and Fibre Channel. Teledyne LeCroy provides protocol analysis, emulation, exerciser and other test equipment to service all NVMe storage applications.
-
product
Non Destructive Testing (NDT)
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI)...show more -
product
Environmental Control System Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
product
LST-2000 Laser Safety Test System
Hangzhou Everfine Photo-E-Info Co., LTD
The system can measure the spectral power distribution, radiant power, radiant energy, apparent light source size, pulse energy and other parameters of the laser light source, and classify the laser light source according to the standard IEC 60825.1. Because laser measurement involves more condition parameters, limit calculation and judgment process is complex, so this system adopts systematic design, the measurement complexity is simplified, the hardware adopts componentization module, users on...show more -
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 6.97kΩ
40-251-030
The 40-251-030 is a programmable resistor module with 4 channels which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
CATV & RF Signal Products
Wuhan Sunma Technology Co., Ltd.
SunmaFiber is a worldwide leading provider for fiber optic equipment, fiber optic test instruments and other data network & telecom products of communications, commercial, and consumer markets. The Company offers test and measurement systems and services to telecommunications service providers, cable operators, and network equipment manufacturers. In addition, the Company offers components, modules, and subsystems for Wireless, Telecommunication, Datacom, Power, Cable TV measurement instruments and utilities applications.
-
product
PXI Thermocouple Simulators
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
product
Load Boards
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
product
Traction Test Rectifiers
A traction test system is defined as a rectifier with a DC output voltage above 400 VDC to a maximum of 4,500 VDC. (Kinetics manufactures only air-cooled systems) A Kinetics test system includes the required OSHA designated safety features for testing power supplies as a minimum for operator interface.
