Protocol Converter
Provide network interoperability between disimiliar protocols.
-
Product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
-
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
Product
RS-232 to RS-422/RS-485 Optically Isolated Interface Converter
Model 245
-
Total Isolation; Selectable RS-422 or RS-485; Selectable 2 or 4 wire RS-485; Intelligent Control of RS-485; TD & RD LED's on Each Side of Opto Barrier; Data Rates up to 128 KBPS. The Model 245 RS-232 to RS-422/RS-485 Optically Isolated Interface Converter is an optically isolated version of the Model 285.
-
Product
AC Power Sources, Frequency Converter
MAC-01, -02, -03
-
For reliability, all models of the Titan AC Power Sources/Frequency Converters are fully current limit protected against either continuous or transient short circuit or overload conditions. When an overcurrent condition exists, the internal current control loop overrides the voltage control loop and scales back the sinewave drive until it sees a safe output current level.
-
Product
Multichannel Voltage Output D/A Converters
-
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.
-
Product
Hardened Media Converter, 1000Mbps, Multimode 850nm, SC
EKI-2741SXI
-
Provides 1 x 1000 Mbps Ethernet port with RJ45 connectorProvides 1 x 1000 Mbps fiber port with SC or SFP (mini-GBIC) type connector for 1000Base-SX/LX deviceProvides DIP switch for full/half duplex settingSupports MDI/MDI-X auto crossoverSupports Auto-NegotiationSupports redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mountProvides Link Fault Pass-through (LFP)Jumbo Frame: 9K bytes
-
Product
PCIe Protocol Analyzer
-
Prodigy Technovations Pvt. Ltd.
The PGY-PCIeGen3/4/5 -PA is a PCIe Protocol Analyzer that supports protocol analysis up to PCIe Gen5 speeds. PCIe design and test engineers can easily captures and record traces at 2.5, 5.0, 8, 16 and 32GT/s at specific event and obtain error report instantaneously at affordable price.
-
Product
Analog-to-Digital Converter (A/D) and Counter-Timer Card
AD8-16 (ADA-8)
-
Model AD8-16 (alternate part number ADA-8) is an economical, multiplexed, eight-bit Analog-to-Digital Converter (A/D) and Counter-Timer card for ISA-bus computers. It accepts up to eight differential or 16 single-ended analog inputs (jumper configured). AD8-16 requires a full-size expansion slot. All connections are made through a standard 50-pin connector. Base I/O address selection is via dip switch.Analog inputs are multiplexed, amplified, held by a sample and hold amplifier, and then digitized by an eight-bit A/D converter. Amplifier gain is selected by software and can differ from channel to channel.
-
Product
Current/Voltage/Frequency Converter
SCMA-VADC-710
-
The SCMA-VADC-710 current/voltage/frequency converter is switched between SensoControl measuring devices and hydraulic installations in order to capture the switching status of these components
-
Product
mAEStro Audio Analog to Digital Converter
-
The mAEStro AADC-100 accepts balanced stereo analog audio inputs and converts them into a single digital bit stream in compliance with the AES/EBU (AES3) and S/PDIF digital audio standards. It generates 24-bit values and uses 128 times over-sampling for extremely accurate and linear analog to digital conversion, as well as offering a high dynamic range with exceptionally low total harmonic distortion and noise.
-
Product
Fibre Channel, Ethernet, & MIL-Firewire Protocol Analyzer
Cipher
-
Avionics Interface Technologies
Supports Multiple Network Protocols including Ethernet, FibreChannel, & MIL-Firewire (AS5643) - High Performance Filtering & Search - Built-in protocol decoders for: FC-AE-ASM, FC-AE-RDMA, FCAE-1553, AS5643, Ethernet, IPv4, IPv6, UDP - User defined “protocol decoders” for custom & proprietary protocols - Database architecture for handling very large data sets - Multiple, Simultaneous views of data sets with time correlation of data across multiple views. - Compatible with common network analysis tools such as - Wireshark (e.g. Imports/Exports to PCAPNG) - Compatible with AIT’s Fibre Channel Test - Instruments for live capture, triggering, and filtering.
-
Product
Voltage Output D/A Converters
-
Analog Devices offers a large family of resistor string and R-2R voltage output (VOUT) D/A converters (DACs). From 8 bits up to 20 bits of resolution, single to 40 channels, integrated or external reference, parallel, LVDS, serial SPI or I2C interface, with high temperature operation, we have a D/A converter to suit your application. We provide precision, buffered, and unbuffered rail-to-rail VOUT D/A converters with up to ±1 LSB INL and DNL specifications and excellent offset and gain error. Our D/A converters work well in a wide variety of open-loop or closed-loop systems—adjusting gain, offset, and many other signals.
-
Product
8FE Managed Ethernet Switch Support Multiple Industrial Protocols,-40~75℃
EKI-5528I-EI
-
8 ports Fast Ethernet RJ-45 (EKI-5528/I-EI)Entry-Level Managed SwitchIXM function enables fast deploymentProvides PROFINET GSDML files, EtherNet/IP EDS (Electronic Data Sheet) file, AOI (Add-On Instructions) file, and FactoryTalk® View faceplateManagement: SNMP v1/v2c/v3, WEB, Standard MIB, Private MIBSupports multiple industrial protocols such as EtherNet/IP, PROFINET and Modbus/TCP
-
Product
I-7000 Remote Data Acquisition Modules Via RS-485 / DCON Protocol
-
The ICP DAS I-7000 distributed I/O communicate over DCON ASCII Protocol over RS-485. They are available in a bevy of Digital and analog configurations, have low power consumption and require +10 ~ +30 VDC. These modules provide cost-effective protection and conditioning for a wide range of valuable industrial control system. They come with free DCON Utility configuration software for setting them up.
-
Product
File Import Tool For Importing And Converting STIL, WGL, VCD/EVCD, ATP Vectors
GtDio6x-FIT
-
Marvin Test Solutions' GtDio6x-FIT option offers test engineers a software tool set for importing and converting STIL, WGL, VDC/EVCD and ATP files to a Marvin Test Solutions' digital instrument file format. GtDio6x-FIT works in conjunction with Marvin Test Solutions' GtDio6x function library software which provides an efficient tool set for developing, debugging, and executing digital test vectors for MTS' GX5296 digital instrument.
-
Product
5VDC Sensor Converter, 5VDC, 15mA
ENVIROMUX-S5VDC-5V
-
External RJ45 device monitors up to two linear DC sensors, 0VDC ~ 5VDC. Output for each sensor: 5VDC, 15mA. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,956,288 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
Current Source-Sink D/A Converters
-
Analog Devices’ current source D/A converters (DACs) portfolio is ideal for photonics control applications where low current noise density, low dropout voltage, and high power efficiency, in addition to high channel density, is critical to system performance. The flexibility of the configurable current source D/A converter outputs, and 300 mA current delivery, make them suitable for resistive heaters and proportional solenoid drive.
-
Product
Scalers & Converters
-
Down convert VGA, HD-SDI, HDMI, and DVI computer video signals to a composite video signal Industry-leading multi-resolution and multi-format signal conversion and scaling products for Pro AV systems.
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
O/E Converter
TIA-3000
-
The TIA-3000 is an instrument for the laboratory or for field use. This amplified optical-electrical converter can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. Energising the unit, the optical signal presented to it is faithfully reproduced on the CRT of the oscilloscope or digitiser.
-
Product
PCI Dual Channel Multi-Band Down Converter
LS-27-D
-
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
Product
Resolver-to-Digital Converter
MSX-RDC-17
-
The resolver-to-digital converter MSX-RDC-17 is a device for supplying and acquiring a resolver. It converts the position value given by the resolver into a digital incremental output signal. The resolution of the incremental encoder output can be defined using the switch on the front side of the MSX-RDC-17.
-
Product
Synchro To Digital & Digital To Synchro Converter
DP-cPCI-5031
-
DP-cPCI-5031 is a Resolver to Digital and Digital to Resolver converter module. This module has four S/R to Digital converters(measurement channels) and two Digital to S/R converter(stimulus channels). This module is programmable for simultaneous acquisition and generation of the Resolver signal.
-
Product
QSPI Protocol Exerciser and Analyzer
PGY-QSPI-EX-PD
-
Prodigy Technovations Pvt. Ltd.
QSPI Protocol Analyzer (PGY-QSPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-QSPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective QSPI designs for its specifications by configuring the PGY-QSPI-EX-PD as Master/Slave, generating QSPI traffic and decoding the QSPI protocol decode packets.
-
Product
USB Converter Cables
-
These converter cables connect various serial interfaces to a computer USB port.
-
Product
PoE Media Converters
-
Upgrade Ethernet networks with PoE powered IP devices in remote locations without replacing existing copper wire infrastructure.
-
Product
DC to Synchro and DC to Resolver Converters
-
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
Product
Low Noise Converter
-
The concept of software defined radios (SDR's) is becoming increasing popular in both commercial, military and Amateur Radio circles. In their basic form, the use simple front end filtering followed by a Quadrature Sampling Detector (QSD) with the post detection processing done in software using the sound card found in PC's. Several popular kits have been developed to introduce Amateurs to the concept.
-
Product
Hardened Media Converter, 1000Mbps, Single Mode 1310nm, 10km, SC
EKI-2741LXI
-
Provides 1x 10/100/1000 Mbps Ethernet port with RJ45 connectorProvides 1 x 1000 Mbps fiber port with Single-mode SC type connectorProvides DIP switch for full/half duplex settingSupports MDI/MDI-X auto crossoverSupports auto-negotiationProvides 3,000 VDC surge (EFT) protectionSupports 4,000 VDC Ethernet ESD protectionSupports +12-48 VDC power inputProvides flexible mounting: DIN-rail & WallmountingProvides Link Fault Pass-through (LFP)Supports wide Operating Temperature from -40 ~ 75° C
-
Product
Airborne Frequency Converter
AFC Series
-
Behlman’s AFC-7000-1 & -2 and AFC-7003, frequency converter are designed to convert three-phase aircraft power to regulated single-phase (115 or 230 VAC) or three-phase (115/200 VAC) at 50 Hz, 60 Hz or 400 Hz. They are ruggedly built to support aircraft takeoffs and landings and designed to meet the input power requirements of MIL-STD-704 and RTCA-DO-160.
-
Product
A/D & D/A Converter Combinations
-
Analog Devices’ comprehensive portfolio of integrated monitoring and control components combine ADCs, DACs, temperature sensors, GPIOs, and current sensing technologies in a wide range of configurations. ADI integrated solutions save space over discrete implementations and simplify operations and provide the configurability your system requires. These products are ideal for general system monitoring of peripherals like power supplies or system voltages and currents. Used in wireless base stations, optical transceivers, transponders, and industrial systems such as building control, these converters offer versatility and flexibility.
