H.265
video coding standard designed with up to a 1:1000 data compression ratio.
-
Product
H(3)TRB & HTGB Test Systems
Test System
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
-
Product
19" Drawer with Writing Surface, Unshielded, 7"H x 24"D
DR-071924-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Active Switching Power Supply Using Mosfet, 125 KW, P/N 5940C2
-
- Active Switching Power Supply Using MOSFET, 125 KW, P/N 5940C2- Input: 480 VAC, 150 Amps, 3 PH, 60 Hz- Output: 0 to 50 VDC, 2500 Amps max- Ten modules in parallel, each module is rated for 0 to 50 VDC, 300 Amps- PLC Control provides Positive Polarity, Negative Polarity and Shuts OFF- Start / Stop capability and EPO- Output voltage and current are displayed on the voltmeter and ammeter- PLC supplied by the customer. We provide a PLC interface only- Indoor enclosure dimensions: 65″W x 50″H x 36″D or (TBD)- Estimated weight: 2000 lbs. or (TBD)
-
Product
Hardness Testers
-
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
Product
7 inch M-IPC-600C ip Camera Tester With 8MP HD-TVI, 8MP-CVI, 8MP AHD
M-IPC-600C
-
Fuzhou Metricu Technology Co Ltd
M-IPC-600C is 7 inch touch screen IP camera tester, that can test H.265 & H.264, 4K IP cameras as well as 8MP HD-TVI camera, 8MP HD-CVI camera, 8MP AHD camera, analog cameras, meanwhile it has PoE output, DC 12V 2A output, etc.
-
Product
CCTV testers
-
1.IPC Tester ,Support H.264/H.265 4K HD IP Camera.2.POE 48V Power Output,Max 24W;3.Support ONVIF, dahua, Hikivision, ACTi,samsung IPC.4. 4.3 inch 800*400 capacitive screen, image display more clearly;5.Built-in WIFI function,can test the Wi-Fi IP Camera;6.Support IP PTZ control functions (ONVIF).7.Support DC12V1A power supply output.8.Support Audio input test.9.Support 4K HD video files and Screen projection function.
-
Product
12 Pulse SCR Controlled High Voltage Power Supply
-
- 12 Pulse SCR Controlled Power Supply, P/N 19435PS- Input: 480 VAC, 300 Amps, 3 PH, 60 Hz- Output: 0 to 3000 VDC ± 10%, 80 Amps max adjustable with potentiometers, and 4/20 mA input signals from the PLC- Output voltage and current are provided as 4/20 mA signals to PLC- Contactor and overload relay are installed for protection- Power ON Light- Start / Stop capability- EPO capability- Manual voltage control and current limit- PLC interface- Output voltage and current are displayed on the voltmeter and ammeter.- A selector switch is used to select between manual Control or PLC Control- The customer is responsible for the PLC controller and PLC programming- Power enclosure, 68″H x 65″W x 44″D- Control enclosure: 20″H x 16″W x 9″D- Weight: 5000 lbs. approximately- All input/output connections are inside the enclosure
-
Product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x2
-
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1x1 Mechanical Optical Switch - Features·Low Insertion Loss·Wide Wavelength Range·Low Crosstalk·Epoxy-free on Optical Path·High Stability, High Reliability·Latching and Non-latchingGLSUN 1x1 Mechanical Optical Switch - Applications·R&D in Laboratory·System Monitoring·MAN (Metropolitan Area Network)·Network Security and Monitoring·OADMGLSUN 1×1 Optical Switch - SpecificationsParametersUnitSUN-FSW-1×1Wavelength Rangenm850±40 / 1300±401260 ~ 1650Test Wavelengthnm850 / 13001310 / 1550Insertion Loss 1,2dBTyp: 0.5 Max: 0.8Typ: 0.4 Max: 0.6Return Loss 1, 2dBMM ≥ 30 SM ≥ 50Crosstalk 1dBMM ≥ 65 SM ≥ 70PDLdB≤0.05WDLdB≤0.25RepeatabilitydB≤±0.02Operating VoltageV3.0 or 5.0DurabilityCycles≥ 10 MillionSwitching Timems≤8Optical PowermW≤500Operating Temperature℃-20 ~ +70Storage Temperature℃-40 ~ +85Relative Humidity%5 ~ 95Weightg14Dimensionmm(L)27.0×(W)12.6×(H)8.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
Product
19" Drawer with Writing Surface, Unshielded, 10.5"H x 24"D
DR-101924-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
L.V.D.T Controller
-
Columbia Research Laboratories
Columbia's single and dual channel microprocessor-based LVDT indicator and set-point controllers are designed for industrial and process control applications utilizing and Columbia H, M, or S series LVDT. IN addition to displaying real-time LVDT readings, these instruments display MIN, MAX and TIR values.
-
Product
24" Drawer with Writing Surface, Unshielded, 8.75"H x 30"D
DR-082430-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
High-Voltage Test Hood
HVE900
-
The large, bright test room with a ball-bearing cover is designed for high production quantities. Thanks to the easily exchangeable exchangeable plate, retrofitting for testing different products is also a simple task. Product properties: External dimensions (W * D * H) approx. 940 * 716 * 640mm Usable test space (W * D * H) approx. 750 * 500 * 460mm Contacting Installation space approx. 100mm high under removable plate Dielectric strength min 10kV Application area up to 2000m above sea level Pollution degree 1 without condensation Standard conformity EN50191 / EN61010-1 Schmersal safety switch AZM161 with guard locking Lid is supported by ball bearings for high number of cycles, the bearings can be easily exchanged for servicing Optionally available, Not included in the price: - Red / green signal light - Mobile substructure trolley with 19 "
-
Product
Conformance Testing Software
Clarinet-TTCN VOIP Interworking ETS
-
Protocol: ITU-T H.225 (11/2000) H.323 (11/2000) and ITU-T Recommendation Q.784.2 (1997)IUT: H323-ISUP gatewayATS: Based on H246 standard of ITU-T written by ACACIA .
-
Product
Zero Field Cavity
-
Zero field cavities generate a zero magnetic field in an air gap. They are mainly used to calibrate hall probes for their zero scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using Zero Field Cavity.
-
Product
ARINC 818 Recorder
-
ARINC 818 Digital Video Recorder powered by Xilinx Zynq Ultrascale+ MPSoC device, is a multi-channel record/playback system that accepts any form of ARINC 818 video input with different resolution & refresh rates. The received ARINC 818 video stream is encoded with the assist of an on-chip H.264/H.265 video codec engine which is capable of performing simultaneous compression and decompression of video streams. Finally, the encoded video is stored in SSD hard drive.
-
Product
BCD to Binary Converter
BCD250
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
Diodes
-
Development target specification*PD=5W class*Capability for load dump surge：ISO7637-2, JASO A-1*Reliability standard：AEC-Q101*Package size：[W×L×H] 12.0×9.6×4.3(mm)
-
Product
AdvancedTCA® Carrier Blade with 4x Intel® Xeon® Processor E3-1515M v5 COM Express Modules and FM10420 Multi-Host Controller
aTCA-9400
Processor Blade
- 4x COM Express Type 6 module slots supporting ADLINK Express-SL/SLE with Xeon® Processor E3-1515M v5 (45W)- Integrated Intel® GT4e GPU providing high-performance H.264/H.265 transcoding- COMe modules connected by Intel® Ethernet Multi-host Controller FM10420, supporting up to 25Gbps Ethernet bandwidth between CPUs- 2x 10G SFP+, 4x 1G RJ-45 Ethernet on front panel- 2x 10G to Fabric channels, 2x1G to Base channels
-
Product
HandyScope HS6-DIFF With EMI, SureConnect & SafeGround: 1 GS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-1000XMEGS-W
-
The powerful capabilities of the WiFiScope HS6-DIFF-1000XMEGS EMI analyzer give the user the possibility to quickly perform a good EMI compliance test. With this cost effective test, time and money are saved by avoiding extra visits to expensive EMC testing facilities. The supplied EMI probe set TP-EMI-HS6 contains three magnetic field (H field) probes and one electric field (E field) probe. The tripod ensures that the probes can be positioned properly at the object under test.
-
Product
PXI H. Density Digital I/O Module 32 Bit O/C
40-410-002
Digital I/O
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface. Two choices of output drive are available: TTL for interacting with external logic and Open Collector Transistor for operating external devices with voltages to 50VDC and currents to 500mA.
-
Product
Digital Multimeter
KU-2600
-
4000 count LCD 2 times / secAuto / Manual Ranging1.5V R6P or AA Batteries (x2)CATⅡ600V, CATⅢ 300V compliant155(H) x 75(W) x 29(D) mm,Approx. 180gHolster, 100-50 Test Leads, 1.5V R6P Batteries (x2 & spare),Spare Fuses F14 (0.5A/250V) (x1), Spare Fuses F17 (10A/250V) (x1),
-
Product
POWERBOX H
-
The Innerspec POWERBOX H is the only hand-held, battery operated instrument capable of generating up to 1200V or 8kW of peak power at speeds of up to 300Hz. For pulse-echo operation, a built-in transmitter/receiver switch permits connecting directly to the instrument with no additional hardware.
-
Product
19" Rackmount Drawer with Keylock, Unshielded, 7"H x 30"D
DR-071930-K
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Wide Measurement Range Model Of Semi-automatic 4 Point Probe Sheet Resistance/resistivity Measurement
RT-3000/RG-2000 (RG-3000)
-
*User programable measurement pattern & programmable measuring pattern*Tester self-test function, wide measuring range*Thickness, edge, temperature correction for silicon wafer*Film thickness conversion function from sheet resistance*2 types measuring tester (S version: Standard type, H version: High range resistivity measurement type)
-
Product
AVoIP Products - 1080p60
-
AVoIP encoders and decoders for HDMI, audio, and R232 signals as well as a controller for controlling and managing H.264 & H.265 IP streams within an ethernet environment
-
Product
IGBT Power Supply, 24 KW, Output 0 to 16 VDC, 1500 AMPS, P/N 6133C
-
IGBT Power Supply, 24 KW, P/N 6133CInput: 480 VAC, 3 PH, 60 HzOutput: 0 to 16 VDC, 1500 AmpsRipple does not degrade when the output voltage is reducedDigital remote with Voltmeter and Ammeter and potentiometers includedDimensions: 20.00”W x 20”H x 24.5”D.Estimated weight: 200 lbs.
-
Product
Transcode Platform
Torque Pelican
-
The Pelican transcode platform provides mass decode-encode functionality for H.264/AVC and H.265/HEVC, for live IP transcode (UDP/RTP/HTTP) and file-based transcode workflows. A complete appliance, Pelican can lead to immediate cost-performance benefits in a number of user cases.
-
Product
LCR Meter, Hand Held, 20 H, 600 µF, 20 Mohm
72-8155
-
72-8155 is a 3-1/2 digit digital capacitance meter with steady operations. The meter measures resistance, capacitance and inductance. The meter has a broad capacitance measurement range and precise accuracy. It can be used in measuring the circuit designed capacitance of cable, switch and PCB layout.
-
Product
Digital AC/DC Auto-Ranging Clamp Meter
PCMT20
-
Measures AC and DCMax. Resolution to Current Measurement: 0.1uALCD Display with BacklightData Hold, Zero Function, Auto Power OffLower Battery Indiactor0.9' (23mm) Jaw SizeDC Voltage: Range: 0-600 V; Accuracy: +/- 0.5%AC Voltage: Range: 0-600 V; Accuracy: +/- 1.5%AC Current: Range: 0-400 A; Accuracy: +/- 3.0%Resistance: Range: 0-40 M; Accuracy: +/- 3.0%Temperature: Range: 1000 C / 1832 F; Accuracy: +/- 3.0%Capacitance: Range: 100 uF; Accuracy: +/- 2.5%Frequency: Range: 150 kHz; Accuracy: +/- 1.2%Continuity: Buzzer Sounds at 100Diode: Test Current 0.3mA; Open Circuit Voltage 1.5VBatteries: 2 x AAA IncludedAccessories Included: Black Bag, Test Leads, Type K Temperature ProbeDimensions: 8.07' H x 2.36' W x 1.18' DWeight: 7.94 ozSold as : Unit
-
Product
Portable Sulphuric Acid Dewpoint Temperature Monitor
-
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6～50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
