Noise Monitors
-
product
Monitoring System
TriGas X5000
The TriGas X5000 Monitoring System is an integrated gas detection solution that helps plant operators comply with NFPA 820. The system monitors for combustible gases, hydrogen sulfide and oxygen with on-board alarming and communication interface to plant and remote location control stations.
-
product
Transportable Monitors
BM 25 & MX 40
Teledyne Gas & Flame Detection
The BM25 packs the benefits of a fixed system area monitor into a rugged, user-friendly and transportable instrument. It was designed to detect one to five gases for mobile or temporary work applications, team protection, area surveillance or places where fixed detection systems are not suitable.Powered by a NiMH battery pack, the BM 25 multi gas monitor offers up to 170 hours of continuous run time. Other standard features include STEL and TWA values, as well as a data logging capacity of more than four months. Multiple units can be grouped using optional alarm transfer kits. This protects larger areas by transferring alarms from one BM 25 to the next. An intrinsically safe trickle charger is also available for long-term area monitoring in classified zones.
-
product
Monitors
Off-air monitoring and + demod/metering equipment for AMFMHD-Radio DBA+ Internet Radio.
-
product
Low Phase Noise Amplifiers
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
product
Phase Monitors
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
product
Monitoring & Management
Avocent®
The Vertiv ™ Avocent® (ADX) ecosystem is a series of IT Management devices and software that provides solutions in edge, enterprise and engineering lab environments. Built upon a secure common architecture the Avocent ADX ecosystem seamlessly integrates and scales to create an open yet resilient IT management fabric.
-
product
Transformer Monitors
The Transformer Advantage is a precision temperature monitor for liquid-immersed power and distribution transformers. It is rugged, fully electronic and field configurable. With Transformer Advantage, users can extend transformer life, utilize maximum capacity and reduce maintenance costs.
-
product
Monitoring
Parker offers a broad range of onsite and laboratory solutions for monitoring, evaluating, and testing a wide variety of substances, from water and hydraulic oil to fuel and various gases, for conditions ranging from insolubility and viscosity levels through flow rate, conductivity, and pressure. They are suitable for use in industrial, marine, and numerous other applications.
-
product
Low Noise Amplifier
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
product
Condition Monitoring
Falcon
The ultimate portable vibration data collector and analyzer. With a wide range of optional features available, the FALCON can be configured to perform balancing, run up coast down, frequency analysis and more.
-
product
Noise & Vibration Measurement Systems
BK8600
Rotation can produce noise and extraneous vibration for any number of reasons and could cause wear, discomfort, or other problems. The BK8600 series of testers are specially designed to test for these.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
-
product
High Frequency Noise Simulator
SKS-H04GA
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
product
Area Monitors
Provides real-time remote radiological monitoring. Local readout of hand-held meter allows for use as a portable survey instrument. More importantly, since the probe’s sensitive electronics are located far from the high field (25 to 350 feet away), they are not subject to destructive gamma exposure. The probe head may be placed directly into a filter compartment or against a resin tank or waste liner.
-
product
Noise Sources
NC1126A
This noise source by Noisecom produces white Gaussian noise up to +13 dBm. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including CATV, Secure communications, Jamming systems, OC-192 Testing, EW & EC.
-
product
Fault Recording Monitors
Comprehensive, flexible, scalable and compatible – full multi-function devices.
-
product
Tiny CAN Monitor
Tiny CAN Monitor - The open source CAN analyzer for Windows, Linux and Mac (in preparation). The software uses the highly developed GTK + library for the GUI and is therefore ideally suited for continuous measurements over several days without a program crash.
-
product
VMware Monitoring & Management
Hyperic HQ
Hyperic HQ for VMware is a pioneering new solution that enables data centers to consolidate complete discovery, monitoring, analysis and control of all application, system and network assets, both inside and outside of the virtual machines powered by VMware.
-
product
Digital Microwave Monitor
TX2000
This instrument is designed specifically for the field service engineer engaged in the repair and maintenance of domestic and commercial microwave heating equipment working at a nominal frequency of 2.45 GHz. Its purpose is the detection of potentially harmful microwave energy leakage from these heating sources.
-
-
product
Monitors
Whether you need a local display, alarm and shutdown capability, data recording, and the ability to communicate using Modbus over Ethernet TCP/IP; or you need to trend waveform and transient data to provide a predictive look at your machine’s condition, Metrix has a solution to meet your machinery monitoring requirements.
-
product
Temperature & Environment Monitors
Room Alert
Monitors Temperature, Humidity, Power, Flood/Water, Smoke/Fire, Motion, Room Entry, Air Flow, Panic Buttons, Network Cameras and more. Offers built-in sensors & allows external sensors to be added.Allows unlimited alert notifications & unlimited users. Allows notification via email, SMS, SMTP, dial-out page, audio alert, webpage update, logfile update and more.
-
product
Monitoring System
A112
The photoelectric sensor model A112 allows to realize a system for detecting breaks of thin wires from 10 um in diameter, with a detection range greater than 50 cm.The A112 produces these results without the use of laser technology, allowing high immunity to vibration and a secure alignment between receiver and transmitter.
-
product
Vibration Monitoring Solution
FLIR SV87-KIT
Vibration trending and analysis can help detect serious problems with industrial machines long before the damage can be seen. That’s why the FLIR SV87-KIT Vibration Monitoring Solution is essential for manufacturing processes that use rotating machinery, industrial pumps, fans, gearboxes, and motors. The included remote monitoring gateway stores sensor data and wirelessly transmits readings in real time to a mobile device or PC. This allows professionals to make knowledgeable decisions about machine operation and maintenance without having to wait for the next manual inspection – reducing unplanned downtime, lowering operational costs, and improving profitability.
-
product
Seismic Analysis and Monitoring
Seismic analysis and monitoring have been designed on the base of the contemporary seismic studies. We can offer you a wide range of tools for geophysical surveys, seismic tomography, automated monitoring of bearing structures (structural health monitoring), seismic monitoring of oil piping systems.
-
product
Water Distribution Monitor
TW-100
HORIBA’s TW-100 is a process water quality measurement system designed for drinking water and water distribution plants. The TW-100 monitors turbidity, color, free chlorine and pressure. This chemical free method reduces operating costs as it requires minimal maintenance and improves process control.
-
product
Tempurature Monitoring System
IQT-Meter
A flexible and economical temperature monitoring system, the IQT features extensive memory and graphic display of temperature history. Similar to the IQM, the IQT System offers software for uploading the temperature data to a P.C. through its serial port. The temperature history can then be displayed with respect to time
-
product
Workhorse Monitor
ADCP
Teledyne Marine RD Instruments
The Monitor is Teledyne RD Instruments’ most popular direct-reading Acoustic Doppler Current Profiler. The unit is typically bottom frame-mounted and hard-wired to shore to provide real-time monitoring of coastal currents.
-
product
Low Noise Filter Adapter
PX0107A
The PX0107A converts Dsub25 outputs to five SMB outputs with the low noise filtering capability down to 25 μVrms (20 MHz). It supports the Keysight M9614/15A.
