-
Product
AC Resonance Test System
-
KV Hipot Power Test Equipment Co.,Ltd
KVXZ-270kVA/270kV Variable Frequency AC Resonance Test System is applied for AC dielectric test for electric equipment.
-
Product
Portable Data Recorder System
PDR
-
Our Portable Data Recorder (PDR) is a low cost, lightweight data acquisition platform for lead paint inspection. It allows the inspector to efficiently identify and record inspection parameters without limitations.PDR interfaces with the Report Generation Software (RGS), streamlining data entry and allowing the inspector to produce instant inspection reports.
-
Product
Digital Secondary Systems
-
Schweitzer Engineering Laboratories, Inc.
SEL digital secondary system solutions (sometimes called digital substation solutions) help protect and control substation primary equipment using digital devices in the secondary system that transmit data via fiber-optic cables. Our flexible, scalable, and economical solutions are built with rugged, field-tested hardware that can withstand harsh environments. Select from two solutions:
-
Product
Four Channel 800MHz Backup Switching System
10942B
-
Universal Switching Corporation
Four Channel Backup Switching System. Multi-mode backup switch for communication and ground station applications. The 10942B Backup IF Switching System provides backup input selections for signals as high as 800MHz. The 10942B delivers ultra-high signal performance coupled with extremely advanced remote/manual control and monitoring.
-
Product
On-board Emissions Measurement System
OBS-ONE PM unit
-
OBS-ONE PM unit is the industry-leading on-board Particulate Matter (PM) measurement system. It collects PM on a filter paper, using a partial flow gravimetric sampling method, while simultaneously measuring real-time PM. A key feature of this design is the use of a venturi flow meter which enables reliable proportional sampling and accurate exhaust gas flow measurement under transient flow conditions. Combine the GAS unit and PM unit to perform certification tests on heavy duty and non-road vehicles.
-
Product
Dynamic Weighing System for Wheel Loaders
Loadtronic 3
-
Modern wheel loaders are designed for increased productivity under all conditions. It is important not to lose these properties after installing a weighing system. The Loadtronic 3 weighing system will never tell you to slow down, even on rough surfaces. It helps your company save time and money and increases your profit. This is possible because the Loadtronic 3 has the built-in dynamics system. Drive as you normally do, move fast and flexible. Load more tons per hour. Instead of giving away valuable goods, load the correct amount every time.
-
Product
Optically Isolated Measurement System
IsoVu
-
IsoVu offers complete galvanic isolation and is the industry’s first measurement solution capable of accurately resolving high bandwidth, low voltage differential signals in the presence of large common mode voltages. The stand out feature of IsoVu™ is its best in class common mode rejection across the entire bandwidth. Accurate differential measurements rely on a measurement system’s bandwidth, rise time, common mode voltage, common mode rejection capability, and the ability to connect to smaller test points to characterize devices that are shrinking in size and increasing in performance. Despite these requirements, advancements in test and measurement for power testing, EMI testing, ESD testing, and remote measurement capability have been minimal at best and have not kept pace with changing requirements. While differential voltage probes have had modest performance gains in regard to bandwidth, these probes have failed to make any substantial improvements in regard to common mode rejection, and connectivity. IsoVu is a leap forward in technology and is the only solution with the required combination of high bandwidth, high common mode voltage, and high common mode rejection to enable these differential measurements.
-
Product
Inspection Systems
-
Video Inspection Systems with?or without measurement capabilities are an excellent way to evaluate and test small items or items in?difficult to access locations. Many options are available in addition to the measurement capability. Video Inspection is used for a variety of purposes including the ability to see? and measure items that are much smaller than the eye can see or that hand tools can measure. Video systems can also reduce the eye and/or back strain associated with production environments where an operator must look in a microscope all day.
-
Product
DC Resistance and Current Measurement System
-
DC Resistance and Current Measurement System including: 6622A Series Bridge, 6634A Temperature Stabilized Resistance Standards, 6664C Scanner(s), world’s most precise and stable 6623A Precision Current Source/Range Extender, Wired Equipment Rack, and Bridgeworks Software.
-
Product
Dry Cryogenic Systems
-
Part of the speciality of QMC Instruments Ltd, is integrating detectors and optics into cryogenic systems, which are suited to it's customers requirements. By packaging our detectors in this way we can ensure that they will perform exactly as quoted.
-
Product
Power Bank Battery Testing System
BTS4000
-
Shenzen Neware Electronic Co LTD
Battery testing system for power banks(BTS-4000-6V4A-CCDC-USB) is based on Neware BTS4000, it shares all the main feature of BTS4000, such as 0.05%FS accuracy, 10Hz data acquisition frequency, based on Ethernet communication, etc.
-
Product
HSI System Test Panel
TA-500
-
This panel was designed to test primarily the NSD360 series of HSI systems. Panel allows running the complete system on the bench. Included is a panel mounted TA-902 API which can also be used for testing external instruments via a panel mounted switch. The API and standard meter drives allow testing many different instruments.
-
Product
Cabinet X-ray System
XPERT 80- L
-
Kubtec's XPERT 80-L, for large area imaging, is a multi-purpose cabinet x-ray system bringing high quality medical-grade imaging and ease of use to applications in scientific research, pathology and industry. A small focal spot with an x-ray source of up to 130 kV offers brighter images with higher contrast for visibility of the smallest details and most subtle variations in density. Optional sources are available for micro-focus and soft x-ray applications.
-
Product
Signal Integration Systems
Avenue
-
The Avenue system includes modules for video up/down conversion, audio embedding, synchronization, conversion, routing, noise reduction, protection switches, test signal generators and more. Avenue signal processing modules are used worldwide in broadcast, mobile, satellite, cable, worship and post production facilities. Avenue is a tray-based signal integration system housed in a 1RU or 3RU frame. Any combination of 1.5 Gb/s HD, 3 Gb/s HD, SD, MPEG, analog video and audio processing modules can be used together in the same frame.
-
Product
NED-LMD Near-Eye Display Measurement Systems
NED-LMD WG Series
-
Gamma Scientific is introducing the NED-LMD Waveguide Tester as the world’s first specialized near-eye display measurement system that mimics human visual perception for fast, accurate and repeatable characterization of next generation optical waveguide-based Augmented/Mixed Reality displays and display components (light engine, waveguide, etc.). This comprehensive offering features a ‘robotic eye’ to help device manufacturers predict how the human eye would perceive their AR/MR displays, quantifying end user experience mapping the entire display field of view.
-
Product
Edge AI Inference System
AIR-101
-
Edge AI Inference System powered by Intel Atom® E3940 QC SoC and two Intel MA2485 VPUs. Intel Atom E3940 Quad Core SoC turbo burst up to 1.8 GHz. Intel® Movidius™ Myriad™ X VPU MA2485 x 2 Built-in.
-
Product
Noise Monitoring Systems
-
It delivers 24/7 connectivity, continuous power capabilities, and a rugged design to simplify your long-term testing.
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
LC/MS/MS Rapid Toxicology Screening System
Ver.3
-
This system improves the efficiency of simultaneous LC/MS/MS analysis methods by allowing the user to start analysis without time-consuming steps such as consideration of separation conditions and MS parameter optimization. Rapid simultaneous analysis methods with analysis times under 15 mins are included for 235 compounds including drugs of abuse, psychoneurotic drugs and sedatives. The system also provides optimised conditions for synchronised survey scans used in screening measurements (conditions adopted for the product ion spectrum as a threshold value for the intensity in MRM).
-
Product
Network Management System (NMS)
-
Schweitzer Engineering Laboratories, Inc.
An NMS is a software application (or set of applications) that provisions, monitors, and maintains communications networks.
-
Product
Regenerative Battery Pack Test System
17040
-
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
Product
Metrology Systems
-
Metrology is essential to control, optimize and ensure the highest yield in semiconductor manufacturing processes. By implementing feedback loops, both process control and process parameter correction are enabled, which allow compliance to tighter process requirements. EVG's metrology solutions are optimized for lithography and all types of bonding applications, and use non-destructive measurement methods. Customers can choose between integration of the metrology technology within fully automated process equipment, or stand-alone metrology systems serving multiple process steps.
-
Product
Specialized Beam Profiler Systems
-
DataRay offers specialized beam profiler systems. These systems offer solutions for complex applications. The large beam profiling system is suitable for beams up to 200 mm image area, and the line laser profiling system provides for direct measurement of line lasers up to 200 mm in length.
-
Product
AC Warning System
AC-15
-
Monitors AC on pipelines or structuresAlarm at 15v AC ThresholdConforms to NACE SP0177-2007Audio and Visual AlarmsCalibration Test UnitSuperbright LED'sReplaceable 9v Batteries
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
-
Product
Mass Flow Test Systems
-
No matter the industry, product integrity is necessary to the manufacturing process. Everything leaks, and mass flow testing provides a fast, reliable determination of leakage to ensure it is within permissible ranges.
-
Product
Magnetic Particle Flaw Inspection System
-
This model can perform every kinds of magnetic particle flaw inspection in our unit. circular magnetization longitudial magnetization continuous magnetization, residual magnetization threading bar magnetization current induction magnetization, AC magnetization AC demagnetization DC magnetization, DC demagnetization.
-
Product
Benchtop X-ray Crystallography System
XtaLAB mini II
-
The Rigaku XtaLAB mini II, benchtop X-ray crystallography system, is a compact single crystal X-ray diffractometer designed to produce publication-quality 3D structures. The perfect addition to any synthetic chemistry laboratory, the XtaLAB mini II will enhance research productivity by offering affordable structure analysis capability without the necessity of relying on a departmental facility. With the XtaLAB mini II, you no longer have to wait in line to determine your structures. Instead your research group can rapidly analyze new compounds as they are synthesized in the lab.
-
Product
Environmental (Radiation) Monitoring System
Hawk® EMS
-
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
Product
Return Band Alignment System
6103/6106
-
Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106).
