HiL Simulation
-
product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
product
Thermal-Mechanical Physical Simulation System
3180 System
Weld HAZ simulation. Melting and solidification. Heat treatmentHot tensile tests. CCT and CHT with deformation. Continuous casting simulation.
-
product
Free Imperas RISC-V Instruction Set Simulator
riscvOVPsim
*RiscvOVPsim - RISC-V Instruction Set Simulator (ISS) - fast, simple, easy to use, cross software development for embedded systems*The riscvOVPsim ISS is an ideal starting point for an embedded software development project. *RiscvOVPsim allows the development and debug of code for the target RISC-V processor on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running riscvOVPsim with an argument to specify the name of the application object.
-
product
Hot Dipping Simulator
HDPS
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
product
Coupler And Decoupler Used With Lightning Impulse Simulation Tester
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Electronic Warfare MMI and HMI Simulators
MS 1600
The EW IFU (Electronic Warfare Interface Unit) interfaces between Cockpit electronics viz., RWR Display Unit (DU), New control Box (NCB), CMDS Control/Display units and Simulator Host Computer (HOST). The EW IFU transmits the status of the cockpit control units to the host, receives display data from the host and transfers the same to RWR DU, NCB and CMDS CCU/CDU. The display data for the RWR DU received from the host would comprise of the complete symbol data in respect of emitters that are to be displayed based on the data from the Instructor Station (IS) and control input from the cockpit. The display unit receives and presents the data as symbology on the display screen. The EW IFU based on the PC–AT.
-
product
4, 8, 16 Or 32 Channel ARINC429Test And Simulation Modules For XMC
AXC429-x
ARINC429 Test and Simulation module for XMC with 4, 8, 16 and 32 programmable Tx/Rx channels plus up to 8 Discrete Inputs/8 Discrete Outputs which can be monitored or generated.
-
product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
product
PCI Strain Gauge Simulator Card, 4-Channel, 1k
50-265-204
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
product
Uphole Simulator
For testing Boom Boxes and other Blasters. The Uphole Simulator is the tool for testing a dynamite blaster in the shop or field. Quick and easy, the UHS unit connects to the high voltage output of the blaster and the uphole geophone input.The UHS sinks the output voltage from the blaster. As it receives the charge, it counts down 30 milliseconds and then outputs a waveform, simulating the signal the blaster might receive from an actual geophone.
-
product
The Imperas Instruction Set Simulator
ISS
The Imperas ISS is often the first simulation product used in an embedded software development project. The Imperas ISS allows the development and debug of code for the target architecture on an x86 host PC with the minimum of setup and effort. It simply requires the cross compilation of your application and running the ISS with an argument to specify the name of the application object.
-
product
GNSS Simulation Engine
Skydel
Test a wide range of applications with advanced GNSS Simulators and helpful tools that generate basic scenarios all the way to complex threat environments, leveraging the power and scalability of the Skydel Simulation Engine. Skydel powers each of Safran Federal Systems' advanced software-defined simulators including BroadSim, BroadSim Anechoic and BroadSim Wavefront.
-
product
Voltage Dip, Interruption& Variation Simulators
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
product
PathWave IC-CAP Simulation and Analysis
W7010E
The W7010E PathWave IC-CAP Simulation and Analysis add-on enables simulation, tuning, and optimization of device behavior using Keysight's PathWave Advanced Design System (ADS) or the provided SPICE3 simulator or by linking directly to supported external simulators.
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
product
SIMULATOR
458-LM-A8-36
Simulates 26 AWG PIC as specified in ANSI T1.417Bandwidth DC to 36 MHzIdeal for testing ADSL, ADSL2, ADSL2+, VDSL, VDSL2 modems/DSLAMs8 channels per line moduleLoop lengths programmable from 0 to 7,500 ft in 500-ft incrementsPlugs into our 458-CC-16 (16-slot chassis) or 458-3SLB (3-Slot chassis)Noise Floor less than -150 dBm/Hz
-
product
Dynamic Data Simulator
LS-70-S
The Lumistar LS-70-S PCI Dynamic Data Simulator allows complex data streams to be generated for evaluation of bit synchronizers and PCM decommutator performance. It can also be used for uplink command generation to vehicles in flight, checkout of complete telemetry links, and playback of archived hard drive data in any format with the appropriate dll. The PCI board is only 7 inches long and contains the dynamic simulator and IRIG Time Code Generator.
-
product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
product
ARINC 429 Test And Simulation PCI Module
PCI-C429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Multi-Spool Network Simulation & Latency Solutions
Fiber Lab 750
from M2 Optics provides the perfect combination of flexibility and efficiency when requiring spools of fiber for testing, latency, and system demonstration applications.
-
product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
product
Simulation and Testing Solutions
LMS
Siemens Digital Industries Software
LMS simulation and testing solutions help manufacturing companies manage the complexities of tomorrow’s product development by incorporating model-based mechatronic simulation and advanced testing solutions in the product development process. Our products and services tune into mission-critical engineering attributes – ranging from system dynamics, structural integrity and sound quality to durability, safety and power consumption.
-
product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
Multi-channel GPS Signal Simulator
MP6220
*Up to 8 channels support positioning test*Can also be used as a single channel
-
product
Au Truck / Bus Fleet Management System (FMS) Simulators
The Au Truck / Bus Fleet Management System (FMS) simulator can generate Controller Area Network (CAN) signal per Truck FMS Standard (Vers. 02.00) and Bus FMS Standard (Vers. 00.02). Au FMS simulators are designed very easy to use. All editions can run independently (without personal computer). Au FMS Simulators are widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration, to product development and product validation.
