BER Test
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: BER Testers
-
product
Count Down Test System
The Second Launch Pad Count Down system is implemented using VXI hardware designed by Data Patterns specific to the application requirements, featuring a redundant system handling upto 14000 I/O points.
-
product
Compact Cable Test Van
ETL-15
ETL-15 is compact enough to be mounted even in a minivan, yet contains all the equipment typically found in a fully-featured cable test and fault location system, including burn module, surge wave generator, time-domain reflectometer and high-voltage DC test module.
-
product
Automatic Wire Test Set
AWTS
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
product
Safety Chamber, Hydrostatic Test
9901HTX-72x24x12
The 6 ft wide by 2 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
product
Temperature shock test chambers test
TSS series
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
product
IAC Test Light
3502
Peaceful Thriving Enterprise Co Ltd
For GM1987 and newer GM model 700 TBI and PFI fuel infection system with flat 4-pin connector. For GM vehicles with throttle body or port fuel injection systems, check the electronic control module signal that provides direction to the idle air control motor.
-
product
AUTOMATED TEST STAND DESIGN
Automated test systems may be as simple as a laptop with a DAQ module or a stand-alone controller, but they typically require a mix of off-the-shelf and custom hardware. All that hardware is integrated and wired into a test stand. Portable or mobile test stands are ideal for in-the-field research and development and servicing of multiple laboratories or manufacturing lines. Test stand access to the front panels of hardware and subcomponents allows manual configuration of non-automated settings. Quick disconnects, cable harnesses, and easy access to probes provides efficient setup and tear-down. Expandable or modular rack mount and card base systems facilitate future needs. Ergonomic considerations include keyboard and display placement, along with number of monintors. Safety is always crucial with proper E-stop placement and keeping dangerous elements away from users.
-
product
Single Ended Test Probes
Single ended probes ranging from 0.4mm to 1.27mm pitchWide selection of plating options to optimize contact challenges and maximize probe lifeVarious length option to provide drop-in replacement capabilityTri-temp applications – 55°C to 155°C
-
product
EMI Test System
EMI-9KA
EMI-9KA is an automatic EMI receiver. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KA is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem. The test results are according to the international format test report. The EMI Test System EMI-9KA fully meets CISPRl6-1, GB17743, FCC, EN55015 and EN55022.
-
product
Test Contactor
cGator
cGator™ singulated power contactor is a top and bottom contacting solution for power Known Good Dies (KGD).Cohu´s patent pending Volta-Flux™ MEMS probe architecture technology provides stable and low CRES for very challenging high-voltage and high-current requirements.The gentle-touch feature reduces surface impacts to a minimum while providing a reliable contact force.
-
product
Meter Test System
MTS-122
Kongter Test & Measurement Co., Limited
This rugged Meter Test System is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 36A). This system is particularly designed with modular structure for calibration and test of analog meter, digital meter, RTU, electrical transducer, energy meter and so on. It is operated under high functionality with user friendly interface.
-
product
Field Test
Field test equipment is an optimised solution for large system testing, which, thanks to its distributed architecture, enables the placement of several small-sized testing systems.
-
product
Manual Test Solution
Titan
Titan is an easy to use, low cost Human Body Model (HBM) or Machine Model (MM) manual test solution. It can be used for design, engineering, and characterization of your devices. Ranging from 50 V to 16,000 V the Titan will have the largest voltage range of any HBM tester.
-
product
Reflectance/Transmittance Test Set
RT-500
An Integrating Sphere is a hollow sphere which has its interior coated with a paint that is nearly perfectly diffuse or Lambertian and which has extremely high reflectance. Light energy introduced in an integrating sphere is reflected from the wall and distributed uniformly around the interior. A detector which is placed at a hole or 'Port' in the sphere wall sees an output which is completely independent of the angularproperties of the input light. The independence of the output of a sphere from the angular properties of the input and the uniform internal distribution of light make integrating spheres ideal for many uses.
-
product
Testing Solution & Battery Emulation
PLUTON
The PLUTON solution is a programmable DC power supply designed to function as a source or a regenerative charge.
-
product
Inline Test Systems
A perfect basis for an automatic integrated Test System for medium to high manufacturing volumes. Important technical and economic advantages due to their modular structure and expansion capability are evident.
-
product
Ultra-Wideband (UWB) Test System
IQgig-UWB
The IQgig-UWB is ideal for both R&D characterization, high-volume production, and certification. Making it the perfect platform to enable a cost-effective, seamless transition from the lab to the manufacturing floor.
-
product
Cold Bend Testing Machine
QualiBend Series
The Cold Bend Testing Machine - QualiBend series are used for bending of metallic materials such as metal rods, planks and steel screw threads. The machines operate with a hydraulic loading system to adjust the distance of the cold-bending press roll to drive the rod in both directions making the cold bending press roll forward and back.
-
product
Power mixed test system
Power device or module with which are digitally controlled and memory can be measured per system.
-
product
Model Based Testing Platform
TestCast MBT
TestCast MBT uses an approach call model based testing (MBT) to drastically reduce the efforts required for test maintenance by generation of test cases from a behavioural model.
-
-
-
product
Sulphur Dioxide Test Chambers
The Sulphur Dioxide Test Chambers from Weiber are Corrosion Test Chambers used for testing the corrosion resistance of metallic surfaces and outer protective layer of coatings. They are used to create a highly corrosive environment rich in corrosive gases and natural humid conditions to induce accelerated corrosion in protective coatings of machines and equipments, electrical items, electronic parts and components, mechanical constructions, automobile and aircraft parts and components etc. Since the corrosive action of Sulphur dioxide also depends on specific temperature and humidity conditions and the presence of other contaminants, the Weiber Sulphur Dioxide Test Chambers are designed to create optimal conditions of temperature and humidity and also make provisions for introducing impurities and contaminants. These equipments operate across a wide temperature range, creating variations in the working temperature to mimic a natural weathering environment.
-
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,13 kg
-
product
Ozone Test Chamber
EKT-2001OZ-HCSSX
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
product
Wafer Test Solutions
Wafer Test Solutions has established leadership positions in developing and deploying application-specific test solutions for MEMS devices, offering wafer and frame probing stations suitable for R&D, Wafer Sort, and Final Test. We offer state-of-the-art solutions to test environmental and motion sensors in wafer and other advanced packages.
-
product
Small Pellets Testing Kit
The ceramic pellets that generally have a diameter between 6 to 12 mm and a thickness of 2 to 4 mm are blocked on a special flange with a disc of soft vermiculite (mica) that has the same high of the ceramic sample and prevents the latter (or the flanges) to toggle. Gold or other appropriate M_Grid™ materials are placed on both sides of the pellet for potential and current measurement. After this operation, the double ceramic felt caps are covering the sample as for any other cell mounting in the Open-Flanges™ test set-up.
-
product
Intelligent Tensile Testing Machine
XLW-H
XLW-H Intelligent Tensile Testing Machine specializes in testing the mechanical properties of various flexible packaging materials. It is mainly used to test the heat seal strength, tensile strength, peel force, elongation of pharmaceutical packaging materials, aluminum foil, PVC hard sheet, composite film, syringe and other products.
-
product
Medical Device Testing
Our experts are qualified to assist you in EMC testing a variety of medical devices, from highly advanced robotic surgical systems, basic over-the-counter devices, and everything in between. Backed by more than 30 years of experience, F2 Labs can provide you with the necessary medical device testing and certification to get your product in the hands of doctors and patients on a timely schedule.
