Bit Error Rate Testers
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received. Also known as: BERT
See Also: BER Testers, BERT
-
product
Current Transformer Tester
CTT
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
product
WINDING COIL TURNS TESTER
VE201R
Winding Turns Tester for Counting Measuring Number of Turns for Air Core Coils, Bobbin Coils or Solenoid Coils. Can Measure : Turns along with Winding Polarity and DC Resistance.Turns Measurement : 1 Turns to 80,000 Turns
-
product
High Spectral Rate and High Dynamic Range Miniature Spectrometers
VS70-HSR & VS70-HDR
VS70 is a high performance compact fiber coupled spectrometer system covering wide spectral range of 200 to 1050 nm. This OEM optical module is built around Horiba’stype-IV Aberration-Corrected Flat-Field Holographic Ion-Etched concave grating and is specially designed to easily adapt to a large variety of detectors and electronic drivers. This system is fitted with a custom variable order-sorting filter to eliminate higher orders.
-
product
Capacitance and Inductance Tester
JY6700
Capacitance measurementsInstrument can test take a single capacitor without stitches in test group capacitance to bring convenience to test. It will show test results of capacitance while show test
-
product
Geotextile Water Permeability Tester
TG010
TESTEX Testing Equipment Systems Ltd.
Geotextile Water Permeability Tester, to determine the constant-head water flow capacity (water permeability) within the plane of a geotextile or geotextile-related product, is measured under varying normal compressive stresses, typical hydraulic gradients and defined contact surface.
-
product
Multicore Universal Solderability Tester
MUST System 3
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
product
Carbon Monoxide Detector Tester
Solo C3
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
product
Battery Testers
Battery testers are designed for the new measurement requirements of the battery industry. They are special for measurement use in low-resistance batteries, large-scale lithium battery packs and fast product sorting in production lines.
-
product
Exhaust Back Pressure Tester
33600
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
product
Stator Testers
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to test varieties of iron stator like pump motor, air-conditioning motor, washing machine motor, paper shredder motor, servo motor and stepper motor etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
product
Comparative Tracking Index Tester
The Comparative Tracking Index Tester is used to test the resistance to tracking of solid insulators or parts of insulators used in electrical appliances and accessories. This test is mandatory for manufacturers of most of the electrical products such as circuit breakers, meters, switches, sockets, plugs, starter holders, connectors, etc.
-
product
Earth Resistance Testers
Earth Resistance Tester is widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc. When measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster.
-
product
Digital Insulation and Continuity Tester
Metra Insu 20
Measurement of the insulation resistance on electrically dead equioment and systems with test voltages up to 1000 V. For testing motors, transformers, generators, switchgears. For testing of house hold appliances. Measurement of the insulation resistance of cables. Very useful for on-site maintenance and service departments.
-
product
Franklin Tester
Model FT1
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
product
Akron Abrasion Tester
UI-FT45
Akron Abrasion Tester is used to test rubber abrasion resistance and it is suitable for rubbers with a hardsness in the range of 55-85IRHDx.
-
product
Temperature & Humidity Testers
Amprobe wireless temperature and humidity testers combine precise, accurate measurement of temperature and humidity with wireless communications up to 80 feet/25 meters to save time and steps. Measure and monitor temperature and relative humidity measurements over time using an Amprobe temperature and humidity data logger. These meters enable you to download measurements to your PC via an USB interface.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Waterproof Salinity Tester
SaltTestr 11
Swtiching between °C and °F is now a breeze with the simple press of a button. Direct temperature readout on the tester saves you the trouble of an additional thermometer.
-
product
Bobbin Winding Coil Tester
SS108A series
Bobbin winding coil testers are used to test various coil of turns. Such as: generator winding turns, transformer winding turns, motor winding turns, inductor winding turns, contactor winding turns, relay winding turns, sparking winding turns, ignition winding turns, speaker voice coil, etc.
-
product
Transmission Line Testers
GAOTek provides affordable, safe and reliable transmission line testers, digital clamp meters and power meters for sale to the United States, Canada and Globally. A transmission line is a specialized cable designed to conduct alternative current of radio frequency. Transmission lines are used for connecting radio transmitters and receivers with their antenna to distribute signals.
-
product
Adapter for 980L-1A Tester
TA-331A
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
product
Network Cable Tester
LightingJoG Rack 8
Sensational 19 inch 2U rack mount Lighting/Network cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection.
-
product
Insulation Tester
Cambridge Instruments & Engineering Co.
'CIE' Insulation Tester is a compact portable unit incorporating most modern features used for direct reading of electrical operating machines, Rotating Plant equipment, Stationary apparatus, Insulation Control switching equipment, Distribution networks, Communication cables, Insulators, Transformers, Industrial Installations, Cable, electrical components, wiring and other devices capable of carrying the rated voltages.
-
product
Digital RCD/RCCB/GFC/ELCB Tester
4112 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 Characters LCD.● Very low consumption.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Zero Crossing Circuitry permit testing at 0° or 180°.● Disconnection Phase Polarity Shown on LCD.● Auto off and off override.● Polarity Trip indicator (Positive or Negative Phase).● Wiring polarity indicator.● Measure voltage between line and earth before testing.● Indicates frequency of voltage L-E.
-
product
Wiremap Tester
MicroMapper
Whether you're an electrical contractor, a home networking professional, datacom specialist or IT/network manager, the Fluke Networks family of powerful Voice/Data/Video (VDV) verification and troubleshooting tools will allow you to verify your work while delivering a quality installation.
-
product
Oil Breakdown Voltage Tester
DPA 75 C
BAUR Prüf- und Messtechnik GmbH
Insulating oil testing with the BAUR DPA 75C. The BAUR DPA 75C oil tester developed especially for mobile use in the field is one of its kind in the market due to its functionality and excellent user benefits in comparison to the costs. The BAUR DPA 75C delivers clear and reliable measurement results.
-
product
Downloadable PAT Tester
Apollo 400+
The Apollo 400+ features a comprehensive range of electrical safety tests with user configurable test sequences and has storage for up to 2,000 test records. Compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
product
PXI Programmable Resistor Module 18x8 Bit, 0 Ohm to 255 Ohm
40-295-121-18/8
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
AMIDA VCSEL Tester
AMIDA VCSEL tester can be divided into three parts: LIV measurement system, Near Field measurement system and Far Field measurement system. To achieve the above three measurements, in addition to the necessary optical components and optical instruments, the core technology is to provide fast and stable current pulses to drive the VCSEL laser diode to emit light, and then to test various optical and electrical properties
-
