-
Product
Broadband VNA Operation To 220 GHz
S93301B
-
Configure a 220 GHz broadband vector network analyzer (VNA) for on-wafer device characterization of emerging 5G and 6G MMICs
-
Product
Rectangular Horn Antennas
-
SAGE Millimeter wave rectangular gain horns, also called pyramidal gain horns, are offered as both standard and custom models with a rectangular waveguide interface. The pyramidal gain horns only support linear polarization. With a calibrated gain chart, these horns can be used to measure the gain of other antennas by comparing the generated signal levels of both. For this reason, these horns are also referred to as standard gain horns. The listed models offer 23 dB nominal gain, 10/11 degrees typical half power beamwidth and 14 dB/30 dB typical side lobe levels at the center frequency of the band. These horns cover full waveguide bandwidths within the frequency range of 8.2 to 170 GHz. In addition to the models listed below, models with 10, 15, 20 and 25 dB gain and other frequency bands are also available.
-
Product
InfiniiMax II Series Probe Amplifier, 12 GHz
1169B
Amplifier
Provides a large common mode range and a large offset range for measuring differential and single-ended signals.
-
Product
1.0 mm Female to Circuit Card Launch, DC to 110 GHz
11923A
Signal Contact (Receiver)
The Keysight 11923A 1.0 mm female connector launch is designed to thread into a package or fixture housing to transition a microwave circuit from microstrip to coaxial connector. The Keysight 11923A connector launch is intended for use with 110 GHz test systems such as the Keysight 8510XF. The Keysight 11923A comes pre-assembled, but the user is responsible for machining the package and installing the connector. The procedure describing the necessary geometry for the package and installation will be provided.
-
Product
RF Connectors
SMA Connectors
-
Utilizing a threaded interface, SMA 50 ohm connectors are semi-precision units that provide excellent electrical performance from DC to 34 GHz and outstanding mechanical durability.
-
Product
THz Pulsed Imaging and Spectroscopy
TeraPulse 4000
-
TeraView’s proprietary semiconductor technology gives the TeraPulse 4000 a market leading signal-to-noise specification with over 90 dB at peak. As standard, the TeraPulse offers a bandwidth of 60 GHz up to typically 4.5 THz; with an option to extend this beyond 6 THz.
-
Product
USB Preamplifier, 10 MHz to 4 GHz
U7227A
Amplifier
The U7227A, 10 MHz to 4 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurements.
-
Product
FET Solid State Switch, 300 kHz to 18 GHz, SPDT
U9397C
Solid-State Relay
The Keysight U9397C solid state switch maximizes your frequency range from 300 kHz up to 18 GHz, offering excellent performance with high isolation, low SWR and fast switching speed. Applications include instrumentation, communications, radar, and many other test systems that require high speed RF and microwave SPDT switching.
-
Product
Antenna Coupler, 300 MHz - 6 GHz
dbCOUPLER
-
The dbCOUPLER is ideal for many different applications including security, GNSS, Bluetooth, WiMAX, Wi-Fi, 5G, LTE, and RFID (vUHF SHF).
-
Product
Modulation Distortion For E5081A Up To 20 GHz
S960704B
-
The Keysight S960704B modulation distortion software application enables fast and accurate active device modulation distortion characterization under modulated signal conditions up to 20 GHz. The wide dynamic range and vector error correction of the ENA-X yield an extremely low residual EVM of the test setup, delivering a complete picture of your device’s signal distortion performance without test system interference. S960704B software measures EVM, NPR, ACPR, and decomposes linear and nonlinear signals by spectrally correlating input and output spectrum without needing to demodulate. Integration with the ENA-X measurement flexibility enables quick modulated signal distortion measurements along with traditional VNA tests.
-
Product
PNA-L Microwave Network Analyzer
N5235B
Network Analyzer
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to50 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Spectrum Analysis For P50xxB Up To 26.5 GHz
S970905B
-
Add spectrum analysis to your P50xxB Streamline series vector network analyzer
-
Product
Cable Assemblies
-
Teledyne Storm Microwave, an industry leader in providing advanced cable assemblies and interconnect products around the globe, has a long and proud heritage serving domestic and overseas defense and telecom markets since 1978.At Teledyne Storm, we manufacture our flexible and semi-rigid coax cable in-house leveraging the highest quality, state-of-the-art equipment and processes. Flexible cable assemblies through 50 GHz are engineered and stringently tested to meet the most demanding requirements for Low Loss, Phase Stability, Durability, and Miniaturization.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-02
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 26.5 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-785C-532-TE
Multiplexer Module
The 40-785C-532-TE (PXI) and 42-785C-532-TE (PXIe) are dual failsafe SP6T 26.5 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
PXIe-5667, 3.6 GHz PXI Vector Signal Analyzer
782366-03
Signal Module
PXIe, 3.6 GHz PXI Vector Signal Analyzer - The PXIe‑5667 is optimized for spectrum monitoring applications such as radio monitoring, interference detection, spectrum regulation, and related applications in line with ITU recommendations. It features real-time signal analysis and advanced signal processing using the capabilities of the built-in FPGA. Additionally, the PXIe‑5667 includes options for various frequency ranges and instantaneous bandwidth.
-
Product
10 MHz to 6 GHz USB Wide Dynamic Range Average Power Sensor
U2051XA
Power Sensor
The Keysight U2051XA is a fast, accurate and wide dynamic range 10 MHz – 6 GHz USB average power sensor.
-
Product
Low Noise Pre-Amplifiers
-
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
Product
Phase Noise Measurement Up To 125 GHz
S930321B
-
S930321B enables phase noise measurements using a PNA or PNA-X vector network analyzer. Simplify your measurement workflow by measuring phase noise on the same connection as your network analysis measurement of 2-port active devices up to 125 GHz, without needing to connect a spectrum analyzer or harmonic mixer.
-
Product
3.5" Embedded SBC With AMD G-Series APU, AMD A55E, LVDS/VGA, Dual LANs, Audio, And PC/104
CAPA112
-
The CAPA112 is a fanless 3.5-inch embedded board with PC/104 for ISA bus expansion. The embedded board is powered by either an AMD Embedded G-Series APU dual core T40E at 1.0 GHz or single core T16R at 615 MHz, paired with the A55E FCH. One DDR3-1066 SO-DIMM on board implements up to 4GB of system memory. Integrated with Radeon™ HD 6250 graphics controller with DirectX 11 support, the super compact 3.5-inch embedded platform delivers unprecedented high definition visual experience. Moreover, it offers -40XC to +70XC (-40XF to +158XF) wide temperature range operation and only requires +12V DC power input into work. The CAPA112 is ideal for applications requiring a power-optimized, rich-graphics and easy integration platform, such as medical imaging, digital signage, kiosks/POI, thin clients and gaming machines.
-
Product
SPARK 6U VPX Development System for Cobalt, Onyx and Jade Boards
Model 8264
-
- 9U 19-inch rackmount, 9-slot, 16-inch deep chassis which houses 6U VPX boards- 64-bit Windows® 7 Professional or Linux® workstation- Intel® Core™ i7 3.6 GHz processor- 16 GB DDR3 SDRAM- ReadyFlow® drivers and board support libraries installed- Out-of-the-box ready-to-run examples
-
Product
PXI/PXIe Microwave Transfer Switch, Dual, 40 GHz, 50 Ω, SMA-2.9, Failsafe, Remote Mount
42-782B-542-E
Switch Module
The 40-782B-542-E (PXI) and 42-782B-542-E (PXIe) dual failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 40 GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
Product
4-Way Power Dividers From 0.5 To 60 GHz
-
Pulsar Microwave's 4-way power dividers are available in narrowband and broadband configurations, covering frequencies from 500 MHz to 60 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
Product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
784966-01
Controller
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
Manual Step Attenuator, DC to 18 GHz; 0 to 70 dB; 10 dB steps
8495B
Attenuator
The Keysight 8495B dc to 18 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 70 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Coaxial Termination, DC to 2 GHz
909C
-
The Keysight 909C is a precision, low-reflection dc to 2 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 909C may be ordered with an APC-7, type-N male, or type-N female connector.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 18 GHz, 50 Ω, SMA, Failsafe
42-784B-123
Multiplexer Module
The 40-784B-123 (PXI) and 42-784B-123 (PXIe) are triple failsafe SP4T 18 GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 1.25 GS/s, 500 MHz Bandwidth
DN2.221-04
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
Pulse Modulator IM-20
-
*Wide Frequency Range: 10 MHz...20 GHz*High Pause Power Mitigation: ≥ 70 dB*Signal Radio Impulse < 10 ns*Parallel Data Input*Input/Output Modulator Ports
