-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 50 GHz, 50 Ω, SMA-2.4, Remote Mount, Failsafe
42-780B-552-E
Relay
The 40-780B-552-E (PXI) and 42-780B-552-E (PXIe) are dual failsafe SPDT 50 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Standard 1.59 (40.40) - 7.00 (198.50) High Frequency Probe
CSP-30TS-011
High Frequency Probe
Nominal Impedance (Ohms): 50Current Capacity (Amps) @ 20° C: 1.00Bandwidth @ -1dB (GHz): 35.00Recommended Travel (mil): 67Recommended Travel (mm): 1.70Full Travel (mil): 100Full Travel (mm): 2.54Overall Length (mil): 1,003Overall Length (mm): 25.48Rec. Mounting Hole Size (mil): 213Rec. Mounting Hole Size (mm): 5.40Test Center (mil): 375Test Center (mm): 9.53
-
Product
MXA Signal Analyzer, Multi-touch, 10 Hz to 50 GHz
N9020B
Signal Analyzer
Quickly adapt to evolving test requirements of wireless devices Shorten test times with hardware-accelerated power measurements, rapid display updates and marker peak searches and fast sweeps Simplify testing with one-button measurements from X-Series applications Capture elusive or transient signals with full-band real-time spectrum analysis
-
Product
Single Sideband IQ Modulators To 16 GHz
-
Single Sideband Modulators incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce either an upper (RF + IF) or lower (RF - IF) sideband when driven by a carrier signal and modulation input signal. Depending on the phase relationship of the signals injected into the MOD.I and MOD.Q ports, the modulator will pass either the upper or lower sideband through to the output while rejecting the other.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-014
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Adapter, 2.4 mm (f) to 2.4 mm (f), DC to 50 GHz
11900B
Coax Adapter
The Keysight 11900B is a metrology-grade, 2.4 mm female to 2.4 mm female adapter with dc to 50 GHz operation.
-
Product
Oscilloscope 25 GHz, 4 Channels
UXR0254B
Oscilloscope
UXR0254B Infiniium UXR-Series is the 25 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope.
-
Product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
-
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-788-121-E
Multiplexer Module
The 40-788-121-E (PXI) and 42-788-121-E (PXIe) are single failsafe SP10T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
CobaltFx 9 GHz 4' FET RF Cable Kit
-
This is a Set of 4 cables, standard length 4 ft, for one extender: ULC50SMSM.4 cable (4)
-
Product
15" XGA Elkhart Lake Thin-Client Terminal With Intel® Atom™/ Celeron® Processor
TPC-315 EHL
Panel PC
Industrial-grade 15" XGA TFT LCD with 70K lifetime and LED backlight.Intel® Elkhart Lake (EHL) Atom™ 6425E 2.00 GHz quad-core / Celeron® J6412 2.00 GHz quad-core processor with 4 GB DDR4 SDRAM.True-flat touchscreen with 5-wire resistive touch control and IP66-rated front panel.Wide operating temperature range (-20 ~ 60 °C/-4 ~ 140 °F).Front-facing LED indicators to show operating status.Built-in Advantech iDoor technology; SSD/HDD bay and VESA mount.Compact, fanless system with aluminum alloy front bezel and chassis grounding protection.Supports Advantech’s SNMP Subagent software.Supports Advantech’s WISE-PaaS/RMM remote management software.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
788167-33
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
PXI-2599, 26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
778572-99
Relay
26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2599 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2599 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
Frontend - Frequency Extension to D-Band (110 GHz to 175 GHz)
FE170ST
-
The R&S®FE170ST is ideal for early subterahertz and 6G research. By extending the frequency ranges for the R&S®SMW200A and R&S®SMM100A to the D band (110 GHz to 175 GHz) engineers can access the range they need and develop the next generation of mobile communications. The easy-to-use, fully-calibrated solution is compatible with our signal generator, analyzer and oscilloscope environments. Plug it in and start designing the next generation of mobile communications today.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-215-014
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
10 MHz to 33 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2063XA
Power Sensor
The Keysight L2063XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz LAN peak power sensor.
-
Product
Coaxial Switches
-
An electromechanical switch made primarily for routing microwave signals/RF energy from one point to another within a transmission line. Coaxial switches can be used in either an industrial environment or in the lab. These electromechanical devices are also used for RF testing equipment and in large RF communication systems and networks. Coaxial switches vary by port configuration, switch type, maximum frequency, isolation, insertion loss, voltage standing wave ratio (VSWR) and package type. Coaxial switches are able to route RF signals over a broad bandwidth from DC to 40 GHz, and are now offered with the Low PIM option which will improve Passive Intermodulation levels from -110dBc (standard switch) to -160dBc.
-
Product
GPS Signal Splitter 16 Way, N Type Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS160
-
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy Type N Female (Jack) Low PIM
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 50 GHz, 50 Ω, SMA-2.4, Failsafe, Remote Mount
40-782B-551-E
Switch Module
The 40-782B-551-E (PXI) and 42-782B-551-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
Product
Fanless Embedded System With Intel® Celeron® N3350 2.4 GHz/ Pentium® N4200 2.5 GHz, HDMI, VGA, 2 GbE LAN, 6 USB And 3 COM
eBOX625-312-FL
-
The eBOX625-312-FL is powered by the Intel® Celeron® processor N3350 or Intel® Pentium® processor quad-core N4200. It has one 204-pin DDR3L-1866 SO-DIMM socket for up to 8GB of memory. With wide operating temperatures and rich I/O interfaces, the rugged embedded box computer is well-suited for Industrial Internet of Things (IIoT), retail equipment, factory automation, and many more. Axiomtek's eBOX625-312-FL offers great customer value with a combination of rich features, good computing performance, flexible connectivity options and effective pricing. It is designed with anti-vibration of up to 3Grms and a wide operating temperature range with non-turbo mode from -20°C to +65°C (-4°F to +149°F). Furthermore, this low power embedded system adopts an IP40-rated rugged aluminum extrusion and steel case, allowing it to withstand operations in harsh and hazardous environments.
-
Product
E-Series Average Power Sensor
E9301B
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm10 MHz to 6 GHz frequency coverage for Wireless Comms formats Low SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Infiniium EXR-Series Oscilloscope: 500 MHz, 4 Channels
EXR054A
Oscilloscope
EXR054A Infiniium EXR-Series, 500 MHz on all 4 channels, options for 7 instruments integrated in one, hardware accelerated plotting, and fully upgradeable to 2.5 GHz and 8 channels
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 3 GHz, 50 Ω, N-Type, Terminated, Remote Mount, Failsafe
42-785C-562-TE
Multiplexer Module
The 40-785C-562-TE (PXI) and 42-785C-562-TE (PXIe) are dual failsafe SP6T 3 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
LXI Microwave Matrix
60-891-006
Matrix Switch Module
The 60-891-006 is a compact 50 Ω microwave switching matrix with added loop-back functionallity and a maximum bandwidth of 18 GHz. It is ideal for constructing complex microwave switching systems for many applications.
-
Product
Step Attenuator
RSC
Attenuator
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
Product
Modulation Distortion Up To 26.5 GHz
S930702B
-
S930702B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 26.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930702B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Logic Analyzer Module With State Mode Up To 4Gb/s
U4164A
-
The U4164A logic analyzer provides industry’s highest data rate state mode (up to 4 Gb/s), highest deep trace timing mode (up to 10 GHz), and deepest memory (up to 400 Mb), enabling validation and debug of DDR4 or LPDDR4 at data rates over 3.5 Gb/s.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-010-013
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
