Product

European Standard for Remote Reading of Measuring Devices

M-Bus

-

HMS Networks

M-Bus - HMS Networks

M-Bus (Meter-Bus) is a European standard for remote reading of measuring devices. M-Bus is predominantly used in buildings, for example in electricity meters, gas meters, water meters or other types of consumption meters. It is also used for various sensors and actuators.

Product

Standard Attitude Gyroscopes

5000B-series

-

Sigma Tek, Inc.

5000B-series - Sigma Tek, Inc.

The 5000B is an air-driven gyro that has a pictorial horizon mask and fixed airplane. The mask moves to indicate climb, dive, and bank. Bank and pitch attitudes are displayed so that the pilot’s sensing of the gyro indication is the same as the interpretation of the relation between the wings of the aircraft and the natural horizon during visual flight.

Product

Cesium Vapour Magnetometer

ENVI Cs

-

Scintrex Limited

ENVI Cs - Scintrex Limited

The ENVI Cs is a continuous reading magnetometer with high sensitivity with integrated navigational GPS and a versatile design that offers the user the ability to maximize productivity.

Product

Additional Products: Standard Voltage 9 Pin D-Type Cables - Connector to Connector

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.

Product

Standard Voltage 50 Pin D-Type Cables - Connector to Connector for Pickering

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 50-pin D-type connector.

Product

Standard Precision GNSS Module

AIW-212

-

Advantech Co. Ltd.

AIW-212 - Advantech Co. Ltd.

Half size mini-PCIe form factorStandard Precision GNSS L1 band92 channel support u-blox NEO-M9N engine (GPS, GLONASS, BeiDou, Galileo, QZSS andSBAS)USB 2.0 communication interfaceAccuracy 2m CEPOperating temperature: -40°C ~ +85°C / -40°F ~ 185°F

Product

Resistivity Standard

-

VLSI Standards, Inc.

VLSI Standards, Inc.

Resistivity Standards are bare silicon wafers available in 3 in, 8 in and 12 in sizes. The silicon is p-type (Boron) doped to nominal resistivity values, from 0.002 ohm.cm to 75 ohm.cm as available on the 3" model.

Product

Open Network Standards

ControlNet

-

HMS Networks

ControlNet - HMS Networks

ControlNet is one of three open network standards (DeviceNet, ControlNet and EtherNet/IP), all of which use a common application layer, the "Common Industrial Protocol" (CIP). The Family of CIP Networks is specified and published by ODVA (Open DeviceNet Vendor Association - http://www.odva.org) and CI (ControlNet International - http://www.controlnet.org).

Product

Automatic Battery with Filters with Standard Contactors

BATLVF1200

-

Lifasa - International Capacitors, SA

BATLVF1200 - Lifasa - International Capacitors, SA

LIFASA automatic capacitor banks are used for centralizedcompensation of power factor in low voltage instalations

Product

GFS Primary Gravimetric Flow Standard

-

Fluke Calibration

Fluke Calibration

The GFS dynamic gravimetric mass flow calibration system allows users to maintain the accuracy and traceability of molblocs or other high precision devices using the same primary reference used by Fluke Calibration. GFS is a true mass flow reference suitable for use in premier measurement institutes who require the lowest measurement uncertainty.

Product

Standard Voltage 37 Pin D-Type Cables - Connector to Unterminated

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.

Product

Standard Optical Interleaver

-

Optoplex Corporation

Optoplex Corporation

An innovative technique for expanding the number of channels per fiber involves an optical device, called an optical interleaver. For example, in most DWDM equipment, the standard channel spacing is 100 GHz. But spacing the signal-carrying frequencies every 50 or even 25 GHz can double or even quadruple the number of channels per fiber. This job is accomplished by an optical interleaver. Such a device takes two multiplexed signals with 100-GHz spacing and interleaves them, creating a DWDM signal with channels spaced 50 GHz apart. The process can be repeated, creating even denser composite signals with 25-GHz or 12.5-GHz spacing. The signals at the receiving end are recovered with the same devices used as splitters or optical de-interleavers. Thus, devices and/or networks can be upgraded without requiring that all devices be upgraded, or network bandwidth can be increased.

Product

Frequency Standards

-

Precision Test Systems Ltd.

Precision Test Systems Ltd.

Precision Test manufacturers a complete range of frequency standards.  This includes rubidium and OXCO models either free running or controlled by an external reference (GPS, GLONASS, Galileo, 1pps, 5 MHz, 10 MHz, IRIG-B etc).  Output frequencies typically 1 MHz, 5 MHz, 10 MHz, 10.23 MHz, 13 MHz, 100 MHz or bespoke frequency.

Product

Decade Resistance Substituter Lab Standard

HARS-LX Series

-

IET Labs

HARS-LX Series - IET Labs

The HARS-LX substituter is a precision resistance source with excellent characteristics of accuracy, stability, temperature coefficient, and power coefficient. All these features serve to make it a laboratory resistance standard, exceeded in performance only by stand-alone standard resistors.

Product

Software Development Standards Compliance Solution

-

Parasoft Corp.

Parasoft Corp.

The most comprehensive development compliance solution; FDA, DO-178B/C, MISRA, JSF, PCI-DSS, ISO, IEC, and more. ntegrate compliance policies into the SDLC and team workflow. Accurately and consistently automate verification and validation tasks

Product

Intex Beam Gauge & Standard Contacts

-

Bowers Group

Bowers Group

Developed to measure both internal and external diameters and lengths, the Intex gauge's aluminium extrusion beam gives it a rigid yet lightweight quality, making it ideal for shop-floor environments. The simple release of a locking thumbscrew enables the gauge's measuring direction to be changed quickly and easily.