Product

Standard Directional Gyroscopes

4000B-series

-

Sigma Tek, Inc.

4000B-series - Sigma Tek, Inc.

The 4000B is our standard air-driven directional gyro. As the aircraft turns left or right, gears on the sensing unit and dial shaft translate this rotation into rotation of the instrument’s vertical dial. Left turns produce clockwise dial rotation and right turns produce counter-clockwise rotation. The gyro is controlled by a heading selector knob located on the lower left of the instrument. Pressing and turning the knob first disengages the dial shaft and then resets the dial to a new heading, which results in a new course indication. Releasing the selector knob re-engages the dial shaft. The on-course position of the pointer is always at the top of the azimuth circle (0° on the dial with the aircraft headed north).

Product

Standard Mechanical Calibration Kit, DC To 9 GHz, Type-N, 50 Ohm

85032F

-

Keysight Technologies

85032F - Keysight Technologies

The Keysight 85032F calibration kit contains precision 50 ohm type-N standards used to calibrate Keysight network analyzers. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 9 GHz.

Product

Standard Gain Horn Antennas

-

Schwarzbeck Mess Elektronik

Schwarzbeck Mess Elektronik

Linear polarized Broadband Horn Antenna (Brass with Plastic mounting body) for Receive and Transmit Applications.

Product

Sematech Analysis and SEMI Standards Analysis

-

Rocky Mountain Laboratories, Inc.

Rocky Mountain Laboratories, Inc.

Rocky Mountain Laboratories, Inc. provides SEMI Standards analyses that conform to the following SEMATECH and SEMI Standards for testing of passivated 316L stainless steel components being considered for installation into a high-purity gas distribution system:SEMASPEC #90120401B-STD (SEM Analysis)SEMASPEC #90120402B-STD (EDS Analysis)SEMASPEC #90120403B-STD (XPS Analysis)SEMASPEC #91060573B-STD (Auger (AES) Analysis)SEMI F60-0306 (based on F60-0301) (XPS Analysis)SEMI F72-1102 (Auger (AES) Analysis)

Product

Standard Digital Isolators

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices’ digital isolators enable designers to implement robust solutions with our magnetically isolated iCoupler products with the flexibility of up to 6 channels. Products meet stringent safety standards including the ability to isolate IS-IS with our intrinsically safe certified digital isolators which enable designs in hazardous areas. And automotive certified versions are also available. Utilizing the iCoupler® and isoPower® technologies, these isolation solutions enable designs without the constraints found in optocouplers.

Product

Standard Voltage 9 Pin D-Type Cables - Calibration Cables for Pickering Products

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The cable assemblies below are suitable for use with Pickering precision resistor cards and modules that utilize 9-pin D-type calibration port connector.

Product

Additional Products: Standard Voltage 50 Pin D-Type Connectors

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.

Product

Standard Transmitter

Tipix 2200

-

IRIS Instruments

Tipix 2200 - IRIS Instruments

The TIPIX 2200 is a transmitter purposely designed for deep Induced Polarisation or Resistivity sounding investigations. This transmitter is generally used together with V-Fullwavers or Elrec Pro receivers. This entry-level instrument has been designed for an ease of use and for a good productivity together with a strong protection against misuse. This very robust device has proven to be reliable even in very cold weather (up to -40°C) or in wet environment. It is able to inject up to 2200W in the soil and to inject up to 13A, so that it is suitable, even on conductive soils, to measure resistivity and IP at medium range depths. It is powered by standard generator.

Product

Absolute Contamination Standards (ACS)

-

VLSI Standards, Inc.

VLSI Standards, Inc.

The Absolute Contamination Standard (ACS) is used to calibrate instruments which size and detect particles on the surface of bare silicon wafers. Use ACS to characterize particles, before particles characterize products.

Product

Resistance Standards

-

Measurements International Ltd.

Measurements International Ltd.

Resistance Standards

Product

Standard Memory Grypper Sockets

-

Ironwood Electronics

Ironwood Electronics

Standard Memory Grypper Sockets

Product

Windows Embedded Standard

-

Advantech Co. Ltd.

Advantech Co. Ltd.

Componentized operating system lets you create a custom operating system image to deliver the necessary functionality for the device. Provide device users with a unique and powerful branded experience.

Product

Conformance Calibration Standard Test Card for GS1-128 Symbol Verifiers

AI-CCS-128-E Rev B

-

Applied Image, Inc.

AI-CCS-128-E Rev B - Applied Image, Inc.

This test card is ideal for testing of verifiers, scanners, and other GS1-128 barcode reading equipment. It also can serve as an excellent training aid to ensure new operators are using the proper methodology and are proven competent in the use of verifiers.