Protocol
A standard way of controlling hardware and/or software that enables connection, communication and data transfer.
See Also: NTCIP, Communication Protocol
-
product
Clock Synchronization
Analog Devices Clock synchronizers are designed for wired networking applications, providing the clock redundancy functionality needed to maximize system uptime. Our technology supports clock synchronization with common standards, including 1 pulse per second (PPS) output signal from a GPS receiver. GPS signals are broadly available and utilize an extremely stable atomic clock as its time base, but they are often noisy. Systems rely on the IEEE1588 timing protocol to establish synchronous communications across the wired network, including synchronous Ethernet and synchronous digital hierarchy (SDH) to optical transport network (OTN) mapping/demapping. The IEEE1588 protocol has emerged as the preferred method for Clock synchronizing systems throughout both computer networks and local area networks (LAN).
-
product
Development Switch
TTESwitch Lab Space
The TTESwitch Lab Space supports laboratory testing efforts of Time-Triggered Ethernet applications; user development costs can be reduced by using the internal TTESwitch Controller HiRel ASIC that is also used in flight equipment. With advanced features like speeds of up to 1 Gbit/s, flexible physical layer configuration and three supported traffic classes, it is the optimal switching solution for a large variety of application areas. TTEthernet is a fault-tolerant, real-time communication protocol for safety-relevant systems integrating Ethernet and TTEthernet data flows onto one physical infrastructure.
-
product
Plug & Play JTAG/SWD Microcontroller Debugger with Built In GDB Server & UART
Black Magic Probe V2.3
In most cases Black Magic Debug takes the form of a firmware for the Black Magic Probe hardware, and implements a GNU DeBugger (GDB) server.The Black Magic GDB server features: - Automatic target detection- No need for target specific configuration scripts- All protocol and target specific control is done through GDB monitor commands- No “software in the middle” like OpenOCD required- Easily scriptable thanks to the GDB scripting capabilities- Interface to the host computer is a standard USB CDC ACM device (virtual serial port), which does not require special drivers on Linux or OS X.- Targets ARM Cortex-M and Cortex-A based microcontrollers- Provides full debugging functionality, including: watchpoints, flash memory breakpoints, memory and register examination, flash memory programming, etc.- [Semihosting / Host IO support] as well as [Serial Wire Debug TRACESWO support].- Implements USB DFU class for easy firmware upgrade as updates become available.- Works with Windows, Linux and Mac environments.
-
product
Envision Analyzer & Generator
MIPI C-PHY/D-PHY
The Envision X14 Analyzer capture utility provides deep analysis for MIPI camera and display protocols over C-PHY and D-PHY layers. The X14 Analyzer can be positioned either as an endpoint to test a CSI-2 or DSI-2 stream or tapped in between a CSI-2 or DSI-2 device and host for passive monitoring and analysis. The Envision X14 ensures fast Time-to-Insight through its rich set of innovative features for debug analysis and identifying and resolving elusive protocol errors.
-
product
cRIO-9805, 4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO
786993-01
4-Port, 802.1AS Ethernet Switch Expansion Module for CompactRIO - The cRIO-9805 is a 4-port Ethernet switch that provides additional ports with 802.1AS network synchronization capability over the 1000 Base-TX network interface. This module supports TCP/IP and UDP network protocols in DHCP + link-local, DHCP, static, and link-local network IP configurations. The cRIO-9805 auto-negotiates communication rates of 10, 100, or 1000 Mbps with its four internally switched ports.
-
product
Free Serial-TCP (More Than Just A Device Server)
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and speed. The Serial-TCP program (more than just a Device Server) bridges your existing Serial COM port and TCP/IP without the need for changing existing protocol. It works seamlessly and transparently, just like passive RS232 / RS485 / RS422 converters, repeaters, and hubs, while the difference is that one requires installation of cables and converters with limited distance; and the other simply makes use of the existing computers and networks with an unlimited transmission distance
-
product
Operator Panels
Advantech offers operator panels including WebOP-2000T and WebOP-3000T series that come with RISC processors to satisfy the stringent standards required in the automation market, With support for over 450 PLC industrial communication protocols can fulfill the needs of different applications.
-
product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Signal Converters
On one hand, there are signal converters which transform an input frequency range into an analog signal. These signal converters are very easy to program and control. Other signal converters can transform analog input signals into analog normalized signals with galvanic insulation. Due to the fact that these signal converters can be freely graduated, they offer endless possibilities and 110 combinations can be selected by means of a DIP switch. Other kinds of signal converters can be connected to devices with RS-232, RS-485 or RS-422 protocols.
-
product
Network Surveillance System
The network backbone contains a wealth of information that can be monitored and collected to support diagnostic, troubleshooting, and fraud prevention activities. Surveillance of network characteristics is becoming more important than ever before. Few important aspects of network surveillance include, Performance Monitoring, Security, Fraud Prevention, Physical Layer monitoring, Billing Verification, Remote Protocol Analysis, Failure Prediction, Traffic Engineering, Call Quality Monitoring and Troubleshooting.
-
product
Fortimus
The digital Fortimus accelerometer delivers sensor performance and the capabilities of the Minimus digitiser in one compact unit. Featuring a touchscreen LCD, Wi-Fi connectivity, Power over Ethernet and Precision Time Protocol, the Fortimus is the ultimate plug-and-play accelerometer
-
product
HTTP Sniffer
EffeTech HTTP Sniffer is a HTTP packet sniffer, protocol analyzer and file reassembly software based on windows platform. Unlike most other sniffers, it is dedicated to capture IP packets containing HTTP protocol, rebuild the HTTP sessions, and reassemble files sent through HTTP protocol. Its smart real-time analyzer enables on-the-fly content viewing while capture, analyze, parse and decode HTTP protocol.
-
product
PXI-7953, Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780340-01
Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7852 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7852 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
-
product
PCIe-6537B, 32-Channel, 50 MHz, 200 MB/s Digital I/O Device
782631-01
32-Channel, 50 MHz, 200 MB/s Digital I/O Device - The PCIe-6537 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
System for the Analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel
SierraNet T328
The SierraNet T328 system provides for analysis of 10/25/40/50/100Gbps Ethernet and Gen 6 (32GFC) Fibre Channel data capture and protocol verification for developers & protocol test engineers in LAN, SAN, NAS and other Ethernet and Fibre Channel applications. Available with eight SFP28 FlexPorts™ for maximum configuration and utility, the SierraNet T328 includes an easy to use, customizable software interface, large capture buffers, and the most advanced T.A.P4 capture, triggering and filtering capabilities in the industry.
-
product
NI-6585B , 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
784060-01
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
product
Conversion Tools
Tester Data Link
VCD/eVCD to tester conversion (via STIL)WGL/TDL to tester conversion (via STIL)Most flexibility to handle complex devices functionality Support protocol definitionUtilize advanced tester features (Such as Xmode, concurrent test etc’… )High Performance Fast run time
-
product
WaveMaster 8000HD High Bandwidth Oscilloscopes
WaveMaster 8000HD Series
WaveMaster 8000HD is the only high speed oscilloscope designed for all stages of product development, whether first-silicon characterization, link validation over channels, or debugging across the entire the protocol stack. No other high speed oscilloscope supports more engineering tasks with more unique tools.
-
product
Factory Automation Projects
Precision Development Consulting Inc
CVD Tool supplier SECS Interface, HSMS Protocol Implementation for a Cell Controller Software Company, Tool Integration in customer fabs for cleaning tool supplier
-
product
Ethernet Testing Network Performance
Networked Communication Solutions, LLC
Xena Networks and Veryx Technologies have created an innovative Ethernet test platform that combines Xena’s high performance, wire-speed Ethernet test hardware with Veryx’s broad portfolio of IP & Ethernet functional and conformance test suites. The result: an affordable, high-performance platform for IP & Ethernet load stress, protocol conformance & functional verification testing.
-
product
Bus Analyzer
FireSpy® 9432bT/9832bT
The FireSpy9432bT and FireSpy9832bT bus analyzer is world’s only 9-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy9432bT/9832bT are the most advanced 1394 test equipment in the market. The FireSpy9432bT/9832bT in fact combine nine FireSpy analyzers in one single instrument. They comprise a significantly more powerful on-board processor and improved connectivity to the host.
-
product
2 Channels, ARINC 568/579 Communications
AR2
The AR2 module provides an ARINC 568/579 communications interface with 2 channels. Channel 1 is Rx and Tx for ARINC 568 and channel 2 is programmable as either Rx or Tx for ARINC 579. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer.
-
product
Remote I/O
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.Remote IO - NuDAM modules provide direct communication with various sensors, including performing signal conditioning, scaling, linearization and conversion to obtain temperature, pressure, flow, voltage, and current measurements. The new ND6100 series modules use Modbus/RTU remote data transmission protocols, providing customers with a comprehensive product portfolio. ADLINK's serial communication cards provide a PCI/PCIe interface and support RS-232 and CAN communication interfaces, allowing customers to choose the most suitable communication card for various automation equipment needs.
-
product
Board
ARINC-708
The Weather Radar protocol consists of 1600-bit ARINC-708 words, which, when interpreted and plotted together, form a picture of weather patterns in the surrounding area. The various weather conditions are indicated by the colors displayed.
-
product
Ethernet/InfiniBand Switch
VPX6-6802
Curtiss-Wright Defense Solutions
The VPX6-6802 is a combined Data Plane and Control Plane high-performance switch for small, mid-size and large 6U VPX systems. As part of the Curtiss-Wright Fabric40™ family of high-speed VPX modules, the VPX6-6802 6U OpenVPX Ethernet & InfiniBand Switch provides centralized switching functionality for HPEC systems and supports both Ethernet and InfiniBand protocols on the Data Plane.
-
product
VB-8054 , 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument
785037-01
4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
product
BRI, PRI and PSTN FXS Simulator
emutel Max
emutel Max is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Max can emulate different country specific networks by adding network personality cards " networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Max.
-
product
Interface
RMAC-VME
Designed for laboratory simulation and production test applications, the Modular Avionics Controller (RMAC) is an intelligent, high performance 6U VME product supporting ARINC protocols and other serial communications. As an evolutionary follow-on product to the successful VME-AIC product line, the RMAC-VME provides a single integrated interface to multiple avionics protocols on VMEbus platforms.
