Protocol
A standard way of controlling hardware and/or software that enables connection, communication and data transfer.
See Also: NTCIP, Communication Protocol
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
Firmware for High-speed HDLC Mode
OP-FW10
-
OP-FW10 is firmware to upgrade protocol analyzer LE-7200/LE-3200 to dedicated analyzer that is specialized for High-speed HDLC communication up to 10Mbps. By installing this OP-FW10 to LE-7200/LE-3200, HDLC measurement processing such as the trigger and filter that were processed by software of the analyzer can be replaced to the hardware processing by FPGA built in the analyzer. Therefore, a maximum speed of HDLC supported is vastly improved. After installation of OP-FW10, You can switch to the usual firmware that supports multi protocol by pressing “SHIFT” and “0” keys at the same time when turning on the power of the analyzer. Therefore, it saves you trouble to reinstall firmware.
-
Product
1211a Optical Receiver/Distribution
-
Precise Time and Frequency, Inc.
To complement the range of high quality frequency and timing references, Precise Time and Frequency, LLC. has now introduced a new Optical Time Code Receiver, with Auto Switching, a full complement of time code outputs, and Ethernet/RS232 remote monitoring/control interface.In addition to the auto switching capability, the new ptf 1211A delivers up to thirty six channels of Time Code outputs, including re-transmission of the optical input. The unit can accept a pair of inputs (usually from separate primary and backup sources), and provides monitoring of both the inputs and outputs for signal integrity.If the primary input fails, the unit will automatically switch to the backup input and indicate a primary signal fault.Full remote monitoring and control via RS232 and Ethernet interfaces includes telnet, http (web browser), and SNMP protocols.
-
Product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-02
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7846 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
PXIe-7865, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
787355-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 160T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7865 features flexibility of timing and synchronization with a user-programmable FPGA for onboard processing and direct control over I/O signals. The PXIe-7865 provides 24 analog output, 2 analog input, and 32, 5V input-tolerant digital I/O channels connected to a Kintex-7 160T FPGA to help you design applications for hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. You can use the dedicated A/D converter (ADC) for independent timing, individual channel triggering, and multirate sampling. Additionally, the PXIe-7865 includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
BRI and PRI Simulator
emutel Ultra
-
emutel Ultra is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Ultra can emulate different country specific networks by adding network personality cards & networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Ultra.
-
Product
Midi Logger
GLT400
-
*Transferring data to PLC via Modbus/TCP protocol*DC Power only for -20 to +60 operation*Supports WEB server, FTP server and FTP client network functions for remote monitoring and controlling*High Isolation inputs to ensure signals are not corrupted by noise from other channels*Connect as a remote terminal unit of GL840
-
Product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Interface Card
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
High-Speed Digital Bus Test Instruments
-
Teradyne and AIT instruments test legacy and newer digital buses.The enormous variety of digital buses used in defense and aerospace applications requires comprehensive, yet efficient testing.Teradyne and AIT COTS instruments meet these challenging bus test requirements for legacy and standardized buses, as well as evolving digital buses that have faster speeds, larger data volumes, and increasingly complex protocols requiring real-time test and emulation.
-
Product
RS-232 Passive Tap Module
EZ-TAP™
-
Stratus Engineering’s EZ-Tap hardware module is a low-cost hardware bus analyzer and protocol analyzer solution that uses a traditional dual COM port approach to RS232 interface monitoring.
-
Product
Multibus Development and Test Tool for ECUs and Networks
CANoe
-
The versatile software tool for development, testing and analysis of ECUs and entire networks. Bus systems: CAN, CAN FD, LIN, MOST, FlexRay, Ethernet, WLAN, Car2x ITS G5, AFDX, J1708, ARINC429 > Protocols: TCP/IP, SOME/IP, CANopen, J1939, ISO 11783, J1587, MCnet, GMLAN, K-Line, CANaerospace and ARINC 825. Others upon request.
-
Product
QSPI Protocol Exerciser and Analyzer
PGY-QSPI-EX-PD
-
Prodigy Technovations Pvt. Ltd.
QSPI Protocol Analyzer (PGY-QSPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-QSPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective QSPI designs for its specifications by configuring the PGY-QSPI-EX-PD as Master/Slave, generating QSPI traffic and decoding the QSPI protocol decode packets.
-
Product
4-Ch Digital Storage Oscilloscope
2194
-
The 2194 combines performance and value all in one portable solution. This oscilloscope provides 100 MHz of bandwidth in a 4-channel configuration with a maximum sample rate of 1 GSa/s and a maximum memory depth of 14 Mpts. The 2194 comes equipped with a 7" widescreen display and extensive features including segmented acquisition, FTT and serial decoding for five different communication protocols. This model is the ideal solution for educational settings and hobbyists.
-
Product
RF Over IP
RFoIP
-
Quintech Electronics and Communications Inc.
A software tool or a feature of a hardware system that allows users to design, control, and manage the routing of Radio Frequency (RF) signals that have been converted into digital data packets and transmitted over an Internet Protocol (IP) network.
-
Product
Carrier Board for Hilscher Fieldbus
SF1-STUDIO
-
SF1-STUDIO is optimized for Hilscher real-time Ethernet & fieldbus modules. Many popular protocols are supported. Ethernet, mezzanine modules are available for EtherCAT, EtherNet/IP, Open-Modbus/TCP, POWERLINK, PROFINET IO, Sercos, and VARAN.
-
Product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
Interface Card
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Wi-Fi/Bluetooth/IoT Wireless Measurement Solution
MP5200
-
*One-to-four parallel high-speed non-signaling test*Support Wi-Fi 802.11ax latest standard*Support Bluetooth V1.x/V2.x/V3.x EDR/BLE V4.x/V5.1 measurement*Support IoT protocol NB-IoT, Zigbee, single-channel GNSS...etc
-
Product
MIL-STD-1553 Interface Board
EXC-4000VME/MCH-x / EXC-4000VXI/MCH-x
-
The EXC-1553VME/MCH and EXC-1553VXI/MCH cards are based on a MIL-STD 1553 certified "Summit" chip used in many flight critical systems. Each dual redundant channel supports both MIL-STD-1553A and MIL-STD 1553B protocols. Up to eight channels may be programmed individually to operate as a Bus Controller, Remote Terminal, Bus Monitor, or Remote Terminal / Concurrent Bus Monitor. The 32 K x 16 of RAM allotted to each channel for the storage of data and control parameters may be updated in real time.
-
Product
PXI-7851, Virtex-5 LX30 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780339-01
Multifunction Reconfigurable I/O
Virtex-5 LX30 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7851 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7851 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
Mixed Signal Oscilloscope: 20 GHz, 4 Analog Plus 16 Digital Channels
MSOV204A
Oscilloscope
20 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Software Development Projects
-
Precision Development Consulting Inc
Automation of new process tool prototype in startup environment, Complex R&D Gasbox Automation, Semiconductor System Control Software, Wafer Transfer Control Software, 300mm Factory Automation, Complete port of Spectrometer software to windows, HSMS Protocol
-
Product
Infrared Gas Detector
iTrans2
-
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
-
Product
Battery Testing System
C8000
-
The Cadex C8000 stands in a class by itself in flexibility and affordable price. Test SMBus batteries, monitor cell balance and capture load signatures to observe batteries with a unique load protocol. Add a thermal chamber, an external load bank, a safety circuit and alarm to form a command center and you begin realizing the unique qualities of this fine battery testing system.
-
Product
Protocol Analyzer and Exerciser
-
Keysight's protocol test solutions for each technology typically consists of both protocol analyzer application as well as a stimulus solution, such as an exerciser or traffic generator. Keysight's protocol test solutions combine multi-protocol analysis, traffic generation, performance and conformance verification to debug, validate and optimize your designs using high speed protocol standards.
-
Product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
SD Card
SD Card v.3.0 / eMMC v.4.51 IP Family
-
Designed for embedded applications that require high performance, small form factor, and high storage capacity, eMMC provides the support for embedded mass storage memory on embedded host systems. The eMMC protocol simplifies the access to NAND flash memories (such as MLC) to the host by hiding the functional differences among suppliers. Compliant to the latest JEDEC eMMC specifications, Arasan’s eMMC IP supports power-on-booting without the upper level software driver. The explicit sleep mode allows the host to instruct the controller to directly enter the sleep mode. The interface supports interface voltage of either 1.8V or 3.3V.
-
Product
DALI 0-10v Converter
-
The DALI 0-10V Converter converts DALI signal to the Analog 0-10V protocol.
-
Product
SSD Test System
-
The Neosem’s SSD test system combines advanced SSDtest hardware, software and environmental chamber into a single platform and supports all popular storage interfaces including PCIe, SAS & SATA and fast emerging protocols such as NVMe and AHCI.
-
Product
Multi-Layer Analyzer
GPON Xpert™
-
The GPON Xpert multi-layer analyzer is a unique protocol analyzer for G-PON products. GPON Xpert is a modular tool designed for R&D, laboratory and field application engineers engaged in the development, testing and deployment of G-PON standard-compliant solutions. GPON Xpert verifies the interoperability of G-PON products offered by different vendors, and indicates compliance of any combination of OLT and ONT/ONU modems to the G-PON standard.
-
Product
Packet Sniffer
EtherDetect
-
EtherDetect Packet Sniffer is an easy for use and award-winning packet sniffer and network protocol analyzer, which provides a connection-oriented view for analyzing packets more effectively. With the handy tool, all you need to do is to set up the filter, start capturing, and view connections, packets as well as data on the fly.
