-
product
For Overhead Distribution Line Current Tester With Power Flow Direction Record
MHR-600
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Measuring and recording the average current values & power flow directions in the setting interval.・Easy to use, as an indirect hot-line work tool.・Memorized data can be outputted to USB memoryafter measurement.・For 6.6KV circuit, protection level IP64.
-
product
10-16 DB Directional Couplers From 0.5 To 50 GHz
Single directional couplers within this series operate from 0.5 MHz to 50 GHz and are available in standard values of 10, 13 and 16 dB. They fulfill narrow and broadband requirements with coupling tolerances of +/- 1 to 1.25 dB. These couplers are optimized for best matching and high directivity with flat coupling response.
-
product
8 SE Or 4 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-8-4C
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
6U VPX Direct RF Processing System
VP460
The VP460 is designed to enable customers to begin development of their next generation systems using revolutionary new processor technology. It is in alignment with the SOSA™ Technical Standard to provide the interoperability required by the US Air Force, Army and Navy.
-
product
Voltage and Current Amplifier
CMS 356
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
product
High Power Single And Dual Directional Couplers
Pulsar Microwave manufactures a line of single and dual directional couplers specifically designed for high power operation. There are various narrow and broadband designs from 0.1 MHz to 10 GHz. These directional couplers come in standard values of 30, 35, 40 and 50 dB with coupling tolerance of +/- 1 dB.The high power directional couplers have low insertion loss. Coupling flatness is maintained at +/- 1 dB or less among models. Most units hold a mainline VSWR of 1.2:1 or better throughout the operating frequency range. Pulsar Microwave has designs up to 2.5 kW input power. Typical directivity is 20 dB or more.Standard outlines are available with SMA or N type female connectors. For higher power ratings, typically the mainline will use N connectors with SMA on the coupled ports.
-
product
High Voltage Surge Current Monitors
HVSCM
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
product
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse
T3CP50-50
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse.
-
product
LXI Reed Relay Matrix - Dual 128x4 Plugin, Direct Y Access, 12 Analog Buses
65-221-001
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
Process / Voltage / Current
Calibrator high precision process signals able to measure and generate current and voltage.
-
product
Automated Leakage Current Tester
LINECHEK® II Series
Our LINECHEK II Leakage Current Tester is designed for medical device manufacturers. With a feature set built around maximizing the efficiency of the Leakage Current test, LINECHEK II satisfies medical application requirements demanding up to 40 Amps of continuous line current. Use it on the bench or in a rack, from the front panel or via a PC interface to ensure your medical device is ready for global deployment.
-
-
product
AC DC Current and Voltage Converters
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
product
PXI/PXIe Wide Current Range Matrix Module, 6x8, 2-Pole, Y Loop-thru
40-514-001
The 40-514-001 (PXI) and 42-514-001 (PXIe) are low density matrices in 6x8 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
AC/DC Current Probe, 50 MHz, 15A
1147B
The 1147B is ideal for capturing transient current signals such as those found in motor controllers, switching power supplies, inverters and current amplifiers driving inductive loads.
-
product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
42-514-104
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Direct Liquid Injection System
VC Series
The VC Series is able to rapidly vaporize pure water or other liquid sources without carrier gas, which enables you to construct a more compact vaporization system.
-
product
AC Current Probe 100 mV/A, 60A, 11 Hz LF Bandwidth, 5MHz HF Bandwidth, 1m cable
T3RC0060-LF
AC Current Probe 100 mV/A, 60A, 11 Hz LF Bandwidth, 5MHz HF Bandwidth, 1m cable.
-
product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
41-752A-901
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
High Current DC Load
3350F Series
3350F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232、USB and LAN interface.
-
product
Current
ACI’s comprehensive current sensor line includes transmitters, switches, and relays—and the technical support to solve the most challenging applications
-
product
Through Hole type AC Current Sensor
CT-6S
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
product
Calibrator, Calibrated w/D & U, Current, 185 mm, 78 mm, 38 mm
72-6694 CAL DU
The 72-6694 CAL DU from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
-
product
Wireless Connectivity AC Clamp Meter with 4000 count / NCV / SPT / Max. 400A AC Current
MS-W364
This is a external wireless connectivity Digital Clamp Meter with 4000 Count, True RMS, auto and manual measurement.
-
product
Current Transformer
ST-9RCT
Standard Electric Works Co., Ltd
● Primary Current Rating (Amp) : 800~2000
-
product
AC Current Probe 1 mV/A, 6,000A, 0.055 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil
T3RC6000-LF
AC Current Probe 1 mV/A, 6,000A, 0.055 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil.
-
product
Current Measurement Board
MS 1814
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
product
High Current Comparators And Power Supplies
Designed in 3D, this custom unit fills the gap between the comparator manufacturers and the production floor. Vidac Solutions does not manufacture CT Comparators, but this unit (and others like it) are used to provide the complex high-current switching, buss-work, source current supply into an enclosure that fits into the production line and provides a safe, ergonomic and easy to use machine for the operators.
