-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Type 39, E-Frame with a 4-slot 6U P&G VPX BP, 600 watt PSU
39E04ASXC8Y2VCF0
-
The Type 39 E-Frame test platform supports 4-slot test & development platform for 6U VPX and OpenVPX™ boards.
-
Product
Rail Pressure Tester
RPT-5
-
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
Product
110V / 100 Amp Load
BD12-110P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 110V battery systems and is extremely costeffective.
-
Product
Powered NIM Crate
NIMpact 300W
-
NIMpact crates are low cost crates that meet EUR4100 and CE specifications. They are outfitted with a 300W power supply with overload and over temperature protection. 5U NIMpact crates are without fan tray.
-
Product
USB/GPIB Interface High-Speed USB 2.0
82357B
-
Easily connect to GBIP instruments from a USB port; no switches, no PC cards, and no external power supplies required.
-
-
Product
Pitot / Static Tester
ADSE 743
-
The ADSE 743 caters fully for all aircraft types and the different electrical power supplies.
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781421-12
Matrix Switch Module
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Signal Amplifier
ZET 412
-
The Signal amplifier ZET 412 with pseudo-galvanic separation is intended for amplification of input signals from various primary transducers and their transmission to the measuring unit (e.g., ZET 210 ADC/DAC unit) as well as for power supply of the connected sensors.
-
Product
Digital Demultiplexers
-
Advanced Science and Novel Technology, Co., Inc.
24:48 digital demultiplexer (DMUX) with SSTL1.5 input and output interfaces.Supports data rates from 1.0Mbps to 2.0Gbps.User-controllable independent internal delays for data and clock signals.1.5V I2C control interface with a user-defined 3-bit chip address.Preset function for synchronization of multiple parallel devices.Full-rate output copy of external high-speed clock input signal.Two pairs of clock divided-by-2 and synchronous clock enable outputs for supporting the tree-type demultiplexation structure.Additional synchronous clock divided-by-4 output.Dual power supply of +3.0V and +1.5V.Industrial temperature range.Low power consumption of 2.1W at 2.0Gbps.Available in custom 256-pin BGA package (13mm x 13mm x 2.5mm).
-
Product
Intelligent Pressure Calibrator
-
Huaxin Instrument (Beijing) Co., Ltd
Here at Huaxin, we offer a selection of HS602 and HX601B intelligent pressure calibrators. They are high pressure, single range digital pressure calibrators with HART communication capability. Composed of high precision measurement chip, 24V DC power supply, battery charging protection circuit, HART communication module and intelligent digital pressure module, these two pressure calibrators provide a pressure calibration solution for gauges, transmitters, and switches over a wide pressure range.
-
Product
ISP Programmer Superpro Is01
-
Features:Until now,Support IC manufacturer, pcs devices and keeps growing.1)High speed thanks to the flexible hardware engine. Programming speed adjustable for complicated application environments brought by user target board, length of ISP cable etc.2)Stand-alone and PC-Hosted (USB2.0 High Speed) dual mode;3)Supports ISP programming of devices with I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 and any other serial port.4)ATE interface;5)Over-current and ESD protection to protect your equipment;6)DLL and API for easy integration into customers’ system.Hardware Specifications:1) ISP cable integrates I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 interfaces。2) VDD (0-5.5V /0.5A) and Vpp (0-15V / 0.2A) lines provided to power the target board and the target devices.3) Cable driver circuit supports target devices of voltage level 1.5-5V and is ESD protected.4) USB 2.0 (high speed) interface for PC hosted mode and management of project files on SD card.5) A 20 Characters x 4 lines LCD and a 6-key keypad are built with it for stand-alone operation. In stand-alone mode project files are stored on the SD card (up to 16GB). The number of the project files is limited only by the capacity of the SD card.6) ATE interface is built for easy external hardware control. 6 lines SEL0-SEL5 are for project selection (maximum 64 files); 2 command lines START and STOP; 3 STATUS lines PASS, FAIL and BUSY. All signals are optical-isolated.7) A universal AC adaptor of DC12V/2A is included for power supply.8)WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility.Software Specifications:1) Supports almost all devices with ISP interface.2) Supports Jam and Staple files from ACTEL and ALTERA; Direct C files from ACTEL.3) Programming speed selectable (High, Normal and Low) for complicated applications such as different cable lengths, different target load characters.4) Dynamic buffer function. Application examples include device S/N, MAC address, frequency or transducer calibration etc.5) File format on SD: FAT16, FAT32.6) Functions for IP protection: Project security, SD security, batch control, administration management etc. 7) API and DLL provided for easy integration into customers’ system like ICT and ATE.8) Software provides the features for multiple units to work concurrently controlled by USB HUB.Applications:1)R&D application like in-circuit test and debug.2)Volume production. Devices may be programmed after the board is fully assembled. One example is the serial number writing to an on-board serial device.3)Field application. Comes with portability, stand-alone mode and mobile data storage media (SD card), it is suitable for field test, debug and data acquisition.4)Third application modules. Friend s/w interface (DLL and Virtual Com communication command set) and h/w interface ( ATE and USB) are provided and make it very easy for customers to integrate ISP01 as a functional module into their systems. One example is the ICT equipment. With this integration user can finish in-circuit test and in-circuit programming in one step.
-
Product
Powered NIM Crate
NIM Compact 150W
-
The WIENER NIM compact series is the low-cost entry into the NIM world. This is achieved by combining the economic steel-aluminum UEN 04 bin with a very compact 150W slot power supply. The result is a lightweight NIM crate with reduced depth. To be compatible to all NIM modules the UEP15 provides all standard (6) DC voltages as well as 115V AC.
-
Product
AC to AC Power Supplies, Output 0 to 25 VAC, 3000 AMPS, 75 KW, P/N 5955C
-
- AC to AC Power Supply, 84 KVA, 1 PH, 60 Hz, P/N 5955C- Input: 240 VAC, 350 Amps- Output: 0 to 25 VAC, 3000 Amps max- Back to back SCR is used to adjust the output voltage- Start / Stop push button- Power ON Light- Voltmeter and Ammeter are included to monitor output voltage and current- Indoor enclosure: 42″H x 32″W x 22″D- Estimated weight: (TBD)
-
Product
DC Voltage Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
DC test systems are used to test components and complete systems found in electrical power supply systems and operating on DC voltage.
-
Product
Electronic Loads
-
Electronic loads are indispensable tools in several fields of electrochemistry, for example in the research of batteries and fuel cells. Using an additional external power supply you easily can extend an EL to a two-quadrant potentiostat you need e.g. in the field of electrolysis.
-
Product
DC System Power Supply, 6 V, 100 A, 600 W
N5741A
Power Supply
The single output, 600 W N5741A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current
-
Product
Absolute Optical Encoder Kit Version
A2K
-
The A2K absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2K reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
Product
IR LightSource
-
Universal LightSources emit Infrared (IR) radiant energy and are designed for the testing of IR(infrared) sensors used in remotely-controlled products.The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
Product
Multipin Industrial Connectors
-
Radiall VanSystem designs and produces circular electrical connectors for professional applications and harsh environments to support a wide range of fields including: railways (in rolling-stock as well as signaling applications), machine tools, automation, construction sites, research, power supply, extractive industries, plant engineering. In addition to connectors with screw or bayonet coupling complying with the MIL-DTL-5015 standard, Radiall VanSystem designs and manufactures non-standard interconnection solutions for special applications.
-
Product
DC Power Supply
PW-7033
-
*Portable type, small size design*Overload protection*3 sets output: 0~32V/0~3A x 2 + 5V/3A*Parallel: 0~64V/0~3A or + 32V ~ -32V/0~3A*Series: 0~32V/0~6A*3 digits, 4 sets LED display, Green is display for voltage, Red is display for current, easy to read, no mistakes.
-
Product
Test Line • Equipment For Testing For Function
-
The test equipment is used for qualitative functional testing of discharge power supply units and / or ionization units from the static line and air line (discharge). The devices are usually operated with a single button and indicate via LED, whether the device under review functions properly.
-
Product
Autoranging System DC Power Supply, 80 V, 510 A, 15000 W, 208 VAC
N8931A
DC Power Supply
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
Product
Ground Leads Continuity Tester
-
Weshine Electric Manufacturing Co., Ltd
1. The new power supply technology is adopted in the grounding down lead conduction tester.2. It has the characteristics of small size, light weight, large output current, good repeatability, strong anti-interference ability and protection function. 3. The whole machine is controlled by single chip microcomputer, which has a high degree of automation. 4. The instrument has high precision and easy operation. The maximum current is 10A.
-
Product
MPOD Universal Low And High Voltage Power Supply System
MPOD--LVHV
-
In addition to the well established 6-, 8- and 12- channel "medium power" low voltage power supplies of the PL506, PL508, PL512- and MARATON - series WIENER presents with Mpod a new, universal multi-channel low voltage (LV) / high voltage (HV) power supply system.
-
Product
2 PICMG® CPU, 7 PCI™, 1 ISA Slots Backplane
HPCI-9S7U
Backplane
- Segment: 1- Slots: 2 PICMG® CPU, 7 PCI™, 1 ISA- Supports AT, ATX power supplies- Dimensions: 213.4 mm x 259.1 mm
-
Product
Autoranging System DC Power Supply, 80 V, 340 A, 10000 W, 400 VAC
N8945A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
GPIB Analog Interfaces
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
30A, 100MHz High Sensitivity Current Probe
CP031A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
