PXI Backplanes
-
Product
PXI 4-Slot BRIC Matrix, 138x8, 1-Pole (3 sub-cards)
40-560B-021-138X8
Matrix Switch Module
The 40-560B-021-138x8 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI BRIC4 FIBO Matrix Dual 93x4 2pin brkout
40-592A-013
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
High Performance 50 MHz Dynamic Digital I/O PXI Subsystem
GX5960 Series
Digital I/O Module
The GX5960 digital subsystem represents the highest level of performance available for PXI-based digital instrumentation and features high performance pin electronics and a timing generator / sequencer in a compact, 6U PXI form factor. The GX5960 series consists of the GX5961 clock generator board with 16 driver / sensor channels and the GX5964 driver / sensor board which supports 32 bi-directional I/O channels. Up to 528 digital I/O channels can be supported by the GX5960 digital subsystem. Each digital channel features a wide drive / sense voltage range of -14 V to +26 V (maximum swing of 24 volts) which can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and a load value (with commutation voltage level) – offering the user complete flexibility when creating test programs and fixtures for multiple UUTs. In addition, each channel offers a parametric measurement unit (PMU) for DC measurements.
-
Product
PXI High Density Multiplexer, 5-Bank, 32-Channel, 1-Pole
40-615A-005
Multiplexer Module
The 40-615A-005 is a 5-bank, 32-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
Dual 4 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-761A-002
Multiplexer Module
The 40-761A-002 terminated dual 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI Triple SPDT RF Switch 3GHz 50 MCX
40-870-103
Switch Module
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI 20Amp 28Volt 4xSPST Automotive Relay
40-180-111
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
Fault Insertion Unit
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI 8 Slot BRIC 132x4 2-pole (3 sub-cards)
40-562A-122-132X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Dual Transfer Switch 18GHz 50Ω SMA
40-782-522
Switch Module
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-034-HI
Programmable Resistor Module
The 40-230-034-HI (PXI) and 42-230-034-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 102kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Microwave Multiplexer, Single SP4T, 26.5GHz, 50Ω, SMA
40-785C-431
Microwave Multiplexer
The 40-785C-431 (PXI) and 42-785C-431 (PXIe) are single SP4T 26.5GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI 2 Amp Multiplexer, Dual 8-Channel, 2-Pole
40-635A-106
Multiplexer Module
The 40-635A-106 is a dual 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
4-Slot BRIC, 168x12, 1 Pole, PXI Matrix (4 Sub-cards)
40-559-401-168x12
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 44x8, 1 Sub-card
40-567A-101
Matrix Switch Module
The 40-567A-101 is a PXI 1-pole 44x8 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 100VDC/70VAC. The 40-567A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 3A Power MUX BRIC, 24-Channel, 12-Pole
40-571-306
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI 8-Slot BRIC Matrix, 110x8 1-Pole (5 sub-cards)
40-562B-121-110X8
Matrix Switch Module
The 40-562B-121-110X8 is a high density BRIC8 matrix module with a size of 110x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4-Slot BRIC Matrix, 264x4 1-Pole (6 sub-cards)
40-562B-021-264X4
Matrix Switch Module
The 40-562B-021-264X4 is a high density BRIC4 matrix module with a size of 264x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Very High Density Versatile 2-Pole, 2 Amp Multiplexer
40-613A-002
Multiplexer Module
The 40-613A Very High Density Versatile 2-pole Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves.
-
Product
PXI Triple SP4T Multiplexer 18GHz 50 SMA
40-784A-123
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Matrix Switch Module
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
PXI Dual 10x4 Matrix 2A 1 Pole
40-546-001
Matrix Switch Module
Model 40-546-001 is a high density dual 1-pole 10x4 power matrix module. It is also available in single 10x4, single 10x8 or single 20x4 relay formats: Typical applications include power routing in Functional ATE systems, specifically automotive electronics, for example testing of Engine Management Units.
-
Product
PXI High Density Multiplexer, 5-Bank, 16-Channel, 1-Pole
40-615A-015
Multiplexer Module
The 40-615A-015 is a 5-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI Monitored Multiplexer, Quad 16-Channel, 1-Pole
40-619-004
Multiplexer Module
The 40-619-004 is a high density PXI 2 A multiplexer module in quad 16-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 102kΩ
40-251-140
Programmable Resistor Module
The 40-251-140 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 102kΩ with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
4-Slot BRIC, 128x16, 1 Pole, PXI Matrix (4 Sub-cards)
40-559-401-128x16
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 264x4 2-pole (6 sub-cards)
40-562A-122-264X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXIe-5113, 500 MHz, 3 GS/s, 8-Bit PXI Oscilloscope
786405-11
Oscilloscope
PXIe, 500 MHz, 3 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5113 oscilloscope has two channels that sample up to 3 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 500 MHz of analog bandwidth.
-
Product
PXI Digital I/O Modules
-
Pickering's PXI Digital I/O Modules are suitable for operating external devices or for interfacing with external logic. Two choices of output drivers are available:*TTL for interacting with external logic*Output channels for operating external devices with voltages to 60VDC and current to 2A
-
Product
PXI 12-Slot BRIC Matrix, 85x32 1-Pole (17 sub-cards)
40-562B-321-85X32
Matrix Switch Module
The 40-562B-321-85X32 is a high density BRIC12 matrix module with a size of 85x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
